config SCSI_AACRAID
tristate "Adaptec AACRAID support"
depends on SCSI && PCI
+ help
+ This driver supports a variety of Dell, HP, Adaptec, IBM and
+ ICP storage products. For a list of supported products, refer
+ to <file:Documentation/scsi/aacraid.txt>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called aacraid.
+
source "drivers/scsi/aic7xxx/Kconfig.aic7xxx"
If unsure, say N.
config SCSI_SATA_VITESSE
- tristate "VITESSE VSC-7174 SATA support"
+ tristate "VITESSE VSC-7174 / INTEL 31244 SATA support"
depends on SCSI_SATA && PCI
help
- This option enables support for Vitesse VSC7174 Serial ATA.
+ This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA.
If unsure, say N.
config SCSI_PPA
tristate "IOMEGA parallel port (ppa - older drives)"
- depends on SCSI && PARPORT
+ depends on SCSI && PARPORT_PC
---help---
This driver supports older versions of IOMEGA's parallel port ZIP
drive (a 100 MB removable media device).
config SCSI_IMM
tristate "IOMEGA parallel port (imm - newer drives)"
- depends on SCSI && PARPORT
+ depends on SCSI && PARPORT_PC
---help---
This driver supports newer versions of IOMEGA's parallel port ZIP
drive (a 100 MB removable media device).
config SCSI_IZIP_EPP16
bool "ppa/imm option - Use slow (but safe) EPP-16"
- depends on PARPORT && (SCSI_PPA || SCSI_IMM)
+ depends on SCSI_PPA || SCSI_IMM
---help---
EPP (Enhanced Parallel Port) is a standard for parallel ports which
allows them to act as expansion buses that can handle up to 64
config SCSI_IZIP_SLOW_CTR
bool "ppa/imm option - Assume slow parport control register"
- depends on PARPORT && (SCSI_PPA || SCSI_IMM)
+ depends on SCSI_PPA || SCSI_IMM
help
Some parallel ports are known to have excessive delays between
changing the parallel port control register and good data being
memory using PCI DAC cycles.
config SCSI_SYM53C8XX_DEFAULT_TAGS
- int "default tagged command queue depth"
+ int "Default tagged command queue depth"
depends on SCSI_SYM53C8XX_2
default "16"
help
exceed CONFIG_SCSI_SYM53C8XX_MAX_TAGS.
config SCSI_SYM53C8XX_MAX_TAGS
- int "maximum number of queued commands"
+ int "Maximum number of queued commands"
depends on SCSI_SYM53C8XX_2
default "64"
help
possible. The driver supports up to 256 queued commands per device.
This value is used as a compiled-in hard limit.
-config SCSI_SYM53C8XX_IOMAPPED
- bool "use port IO"
+config SCSI_SYM53C8XX_MMIO
+ bool "Use memory mapped IO"
depends on SCSI_SYM53C8XX_2
+ default y
help
- If you say Y here, the driver will use port IO to access
- the card. This is significantly slower then using memory
- mapped IO. Most people should answer N.
+ Memory mapped IO is faster than Port IO. Most people should
+ answer Y here, but some machines may have problems. If you have
+ to answer N here, please report the problem to the maintainer.
config SCSI_IPR
tristate "IBM Power Linux RAID adapter support"
To compile this driver as a module, choose M here: the
module will be called qlogicfas.
-config SCSI_QLOGIC_FC
- tristate "Qlogic ISP FC SCSI support"
- depends on PCI && SCSI
- help
- This is a driver for the QLogic ISP2100 SCSI-FCP host adapter.
-
- To compile this driver as a module, choose M here: the
- module will be called qlogicfc.
-
config SCSI_QLOGIC_FC_FIRMWARE
bool "Include loadable firmware in driver"
depends on SCSI_QLOGIC_FC
config ZFCP
tristate "FCP host bus adapter driver for IBM eServer zSeries"
- depends on ARCH_S390 && QDIO && SCSI
+ depends on S390 && QDIO && SCSI
select SCSI_FC_ATTRS
help
If you want to access SCSI devices attached to your IBM eServer