config SCSI_AHA152X
tristate "Adaptec AHA152X/2825 support"
depends on ISA && SCSI && !64BIT
+ select SCSI_SPI_ATTRS
---help---
This is a driver for the AHA-1510, AHA-1520, AHA-1522, and AHA-2825
SCSI host adapters. It also works for the AVA-1505, but the IRQ etc.
config SCSI_AACRAID
tristate "Adaptec AACRAID support"
depends on SCSI && PCI
+ help
+ This driver supports a variety of Dell, HP, Adaptec, IBM and
+ ICP storage products. For a list of supported products, refer
+ to <file:Documentation/scsi/aacraid.txt>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called aacraid.
+
source "drivers/scsi/aic7xxx/Kconfig.aic7xxx"
If unsure, say N.
config SCSI_SATA_VITESSE
- tristate "VITESSE VSC-7174 SATA support"
+ tristate "VITESSE VSC-7174 / INTEL 31244 SATA support"
depends on SCSI_SATA && PCI
help
- This option enables support for Vitesse VSC7174 Serial ATA.
+ This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA.
If unsure, say N.
config SCSI_DMX3191D
tristate "DMX3191D SCSI support"
depends on PCI && SCSI
+ select SCSI_SPI_ATTRS
help
This is support for Domex DMX3191D SCSI Host Adapters.
config SCSI_DTC3280
tristate "DTC3180/3280 SCSI support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
help
This is support for DTC 3180/3280 SCSI Host Adapters. Please read
the SCSI-HOWTO, available from
config SCSI_GENERIC_NCR5380
tristate "Generic NCR5380/53c400 SCSI PIO support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
---help---
This is a driver for the old NCR 53c80 series of SCSI controllers
on boards using PIO. Most boards such as the Trantor T130 fit this
config SCSI_GENERIC_NCR5380_MMIO
tristate "Generic NCR5380/53c400 SCSI MMIO support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
---help---
This is a driver for the old NCR 53c80 series of SCSI controllers
on boards using memory mapped I/O.
config SCSI_PPA
tristate "IOMEGA parallel port (ppa - older drives)"
- depends on SCSI && PARPORT
+ depends on SCSI && PARPORT_PC
---help---
This driver supports older versions of IOMEGA's parallel port ZIP
drive (a 100 MB removable media device).
config SCSI_IMM
tristate "IOMEGA parallel port (imm - newer drives)"
- depends on SCSI && PARPORT
+ depends on SCSI && PARPORT_PC
---help---
This driver supports newer versions of IOMEGA's parallel port ZIP
drive (a 100 MB removable media device).
config SCSI_IZIP_EPP16
bool "ppa/imm option - Use slow (but safe) EPP-16"
- depends on PARPORT && (SCSI_PPA || SCSI_IMM)
+ depends on SCSI_PPA || SCSI_IMM
---help---
EPP (Enhanced Parallel Port) is a standard for parallel ports which
allows them to act as expansion buses that can handle up to 64
config SCSI_IZIP_SLOW_CTR
bool "ppa/imm option - Assume slow parport control register"
- depends on PARPORT && (SCSI_PPA || SCSI_IMM)
+ depends on SCSI_PPA || SCSI_IMM
help
Some parallel ports are known to have excessive delays between
changing the parallel port control register and good data being
memory using PCI DAC cycles.
config SCSI_SYM53C8XX_DEFAULT_TAGS
- int "default tagged command queue depth"
+ int "Default tagged command queue depth"
depends on SCSI_SYM53C8XX_2
default "16"
help
exceed CONFIG_SCSI_SYM53C8XX_MAX_TAGS.
config SCSI_SYM53C8XX_MAX_TAGS
- int "maximum number of queued commands"
+ int "Maximum number of queued commands"
depends on SCSI_SYM53C8XX_2
default "64"
help
possible. The driver supports up to 256 queued commands per device.
This value is used as a compiled-in hard limit.
-config SCSI_SYM53C8XX_IOMAPPED
- bool "use port IO"
+config SCSI_SYM53C8XX_MMIO
+ bool "Use memory mapped IO"
depends on SCSI_SYM53C8XX_2
+ default y
help
- If you say Y here, the driver will use port IO to access
- the card. This is significantly slower then using memory
- mapped IO. Most people should answer N.
+ Memory mapped IO is faster than Port IO. Most people should
+ answer Y here, but some machines may have problems. If you have
+ to answer N here, please report the problem to the maintainer.
config SCSI_IPR
tristate "IBM Power Linux RAID adapter support"
config SCSI_PAS16
tristate "PAS16 SCSI support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
---help---
This is support for a SCSI host adapter. It is explained in section
3.10 of the SCSI-HOWTO, available from
To compile this driver as a module, choose M here: the
module will be called qlogicfas.
-config SCSI_QLOGIC_FC
- tristate "Qlogic ISP FC SCSI support"
- depends on PCI && SCSI
- help
- This is a driver for the QLogic ISP2100 SCSI-FCP host adapter.
-
- To compile this driver as a module, choose M here: the
- module will be called qlogicfc.
-
config SCSI_QLOGIC_FC_FIRMWARE
bool "Include loadable firmware in driver"
depends on SCSI_QLOGIC_FC
config SCSI_T128
tristate "Trantor T128/T128F/T228 SCSI support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
---help---
This is support for a SCSI host adapter. It is explained in section
3.11 of the SCSI-HOWTO, available from
config ATARI_SCSI
tristate "Atari native SCSI support"
depends on ATARI && SCSI && BROKEN
+ select SCSI_SPI_ATTRS
---help---
If you have an Atari with built-in NCR5380 SCSI controller (TT,
Falcon, ...) say Y to get it supported. Of course also, if you have
config MAC_SCSI
bool "Macintosh NCR5380 SCSI"
depends on MAC && SCSI=y
+ select SCSI_SPI_ATTRS
help
This is the NCR 5380 SCSI controller included on most of the 68030
based Macintoshes. If you have one of these say Y and read the
config MVME147_SCSI
bool "WD33C93 SCSI driver for MVME147"
depends on MVME147 && SCSI=y
+ select SCSI_SPI_ATTRS
help
Support for the on-board SCSI controller on the Motorola MVME147
single-board computer.
config MVME16x_SCSI
bool "NCR53C710 SCSI driver for MVME16x"
depends on MVME16x && SCSI && BROKEN
+ select SCSI_SPI_ATTRS
help
The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710
SCSI controller chip. Almost everyone using one of these boards
config BVME6000_SCSI
bool "NCR53C710 SCSI driver for BVME6000"
depends on BVME6000 && SCSI && BROKEN
+ select SCSI_SPI_ATTRS
help
The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710
SCSI controller chip. Almost everyone using one of these boards
config SUN3_SCSI
tristate "Sun3 NCR5380 SCSI"
depends on SUN3 && SCSI && BROKEN
+ select SCSI_SPI_ATTRS
help
This option will enable support for the OBIO (onboard io) NCR5380
SCSI controller found in the Sun 3/50 and 3/60, as well as for
config ZFCP
tristate "FCP host bus adapter driver for IBM eServer zSeries"
- depends on ARCH_S390 && QDIO && SCSI
+ depends on S390 && QDIO && SCSI
select SCSI_FC_ATTRS
help
If you want to access SCSI devices attached to your IBM eServer