/*
- * An I2C driver for the Ricoh RS5C372 RTC
+ * An I2C driver for Ricoh RS5C372 and RV5C38[67] RTCs
*
* Copyright (C) 2005 Pavel Mironchik <pmironchik@optifacio.net>
* Copyright (C) 2006 Tower Technologies
#include <linux/rtc.h>
#include <linux/bcd.h>
-#define DRV_VERSION "0.3"
+#define DRV_VERSION "0.5"
-/* Addresses to scan */
-static unsigned short normal_i2c[] = { /* 0x32,*/ I2C_CLIENT_END };
-
-/* Insmod parameters */
-I2C_CLIENT_INSMOD;
+/*
+ * Ricoh has a family of I2C based RTCs, which differ only slightly from
+ * each other. Differences center on pinout (e.g. how many interrupts,
+ * output clock, etc) and how the control registers are used. The '372
+ * is significant only because that's the one this driver first supported.
+ */
#define RS5C372_REG_SECS 0
#define RS5C372_REG_MINS 1
#define RS5C372_REG_HOURS 2
#define RS5C372_REG_MONTH 5
#define RS5C372_REG_YEAR 6
#define RS5C372_REG_TRIM 7
+# define RS5C372_TRIM_XSL 0x80
+# define RS5C372_TRIM_MASK 0x7F
+
+#define RS5C_REG_ALARM_A_MIN 8 /* or ALARM_W */
+#define RS5C_REG_ALARM_A_HOURS 9
+#define RS5C_REG_ALARM_A_WDAY 10
+
+#define RS5C_REG_ALARM_B_MIN 11 /* or ALARM_D */
+#define RS5C_REG_ALARM_B_HOURS 12
+#define RS5C_REG_ALARM_B_WDAY 13 /* (ALARM_B only) */
+
+#define RS5C_REG_CTRL1 14
+# define RS5C_CTRL1_AALE (1 << 7) /* or WALE */
+# define RS5C_CTRL1_BALE (1 << 6) /* or DALE */
+# define RV5C387_CTRL1_24 (1 << 5)
+# define RS5C372A_CTRL1_SL1 (1 << 5)
+# define RS5C_CTRL1_CT_MASK (7 << 0)
+# define RS5C_CTRL1_CT0 (0 << 0) /* no periodic irq */
+# define RS5C_CTRL1_CT4 (4 << 0) /* 1 Hz level irq */
+#define RS5C_REG_CTRL2 15
+# define RS5C372_CTRL2_24 (1 << 5)
+# define RS5C_CTRL2_XSTP (1 << 4)
+# define RS5C_CTRL2_CTFG (1 << 2)
+# define RS5C_CTRL2_AAFG (1 << 1) /* or WAFG */
+# define RS5C_CTRL2_BAFG (1 << 0) /* or DAFG */
+
+
+/* to read (style 1) or write registers starting at R */
+#define RS5C_ADDR(R) (((R) << 4) | 0)
+
+
+enum rtc_type {
+ rtc_undef = 0,
+ rtc_rs5c372a,
+ rtc_rs5c372b,
+ rtc_rv5c386,
+ rtc_rv5c387a,
+};
-#define RS5C372_TRIM_XSL 0x80
-#define RS5C372_TRIM_MASK 0x7F
+/* REVISIT: this assumes that:
+ * - we're in the 21st century, so it's safe to ignore the century
+ * bit for rv5c38[67] (REG_MONTH bit 7);
+ * - we should use ALARM_A not ALARM_B (may be wrong on some boards)
+ */
+struct rs5c372 {
+ struct i2c_client *client;
+ struct rtc_device *rtc;
+ enum rtc_type type;
+ unsigned time24:1;
+ unsigned has_irq:1;
+ char buf[17];
+ char *regs;
+};
-#define RS5C372_REG_BASE 0
+static int rs5c_get_regs(struct rs5c372 *rs5c)
+{
+ struct i2c_client *client = rs5c->client;
+ struct i2c_msg msgs[] = {
+ { client->addr, I2C_M_RD, sizeof rs5c->buf, rs5c->buf },
+ };
+
+ /* This implements the third reading method from the datasheet, using
+ * an internal address that's reset after each transaction (by STOP)
+ * to 0x0f ... so we read extra registers, and skip the first one.
+ *
+ * The first method doesn't work with the iop3xx adapter driver, on at
+ * least 80219 chips; this works around that bug.
+ */
+ if ((i2c_transfer(client->adapter, msgs, 1)) != 1) {
+ dev_warn(&client->dev, "can't read registers\n");
+ return -EIO;
+ }
-static int rs5c372_attach(struct i2c_adapter *adapter);
-static int rs5c372_detach(struct i2c_client *client);
-static int rs5c372_probe(struct i2c_adapter *adapter, int address, int kind);
+ dev_dbg(&client->dev,
+ "%02x %02x %02x (%02x) %02x %02x %02x (%02x), "
+ "%02x %02x %02x, %02x %02x %02x; %02x %02x\n",
+ rs5c->regs[0], rs5c->regs[1], rs5c->regs[2], rs5c->regs[3],
+ rs5c->regs[4], rs5c->regs[5], rs5c->regs[6], rs5c->regs[7],
+ rs5c->regs[8], rs5c->regs[9], rs5c->regs[10], rs5c->regs[11],
+ rs5c->regs[12], rs5c->regs[13], rs5c->regs[14], rs5c->regs[15]);
-struct rs5c372 {
- u8 reg_addr;
- u8 regs[17];
- struct i2c_msg msg[1];
- struct i2c_client client;
- struct rtc_device *rtc;
-};
+ return 0;
+}
-static struct i2c_driver rs5c372_driver = {
- .driver = {
- .name = "rs5c372",
- },
- .attach_adapter = &rs5c372_attach,
- .detach_client = &rs5c372_detach,
-};
+static unsigned rs5c_reg2hr(struct rs5c372 *rs5c, unsigned reg)
+{
+ unsigned hour;
-static int rs5c372_get_datetime(struct i2c_client *client, struct rtc_time *tm)
+ if (rs5c->time24)
+ return BCD2BIN(reg & 0x3f);
+
+ hour = BCD2BIN(reg & 0x1f);
+ if (hour == 12)
+ hour = 0;
+ if (reg & 0x20)
+ hour += 12;
+ return hour;
+}
+
+static unsigned rs5c_hr2reg(struct rs5c372 *rs5c, unsigned hour)
{
+ if (rs5c->time24)
+ return BIN2BCD(hour);
+
+ if (hour > 12)
+ return 0x20 | BIN2BCD(hour - 12);
+ if (hour == 12)
+ return 0x20 | BIN2BCD(12);
+ if (hour == 0)
+ return BIN2BCD(12);
+ return BIN2BCD(hour);
+}
- struct rs5c372 *rs5c372 = i2c_get_clientdata(client);
- u8 *buf = &(rs5c372->regs[1]);
+static int rs5c372_get_datetime(struct i2c_client *client, struct rtc_time *tm)
+{
+ struct rs5c372 *rs5c = i2c_get_clientdata(client);
+ int status = rs5c_get_regs(rs5c);
- /* this implements the 3rd reading method, according
- * to the datasheet. rs5c372 defaults to internal
- * address 0xF, so 0x0 is in regs[1]
- */
+ if (status < 0)
+ return status;
- if ((i2c_transfer(client->adapter, rs5c372->msg, 1)) != 1) {
- dev_err(&client->dev, "%s: read error\n", __FUNCTION__);
- return -EIO;
- }
+ tm->tm_sec = BCD2BIN(rs5c->regs[RS5C372_REG_SECS] & 0x7f);
+ tm->tm_min = BCD2BIN(rs5c->regs[RS5C372_REG_MINS] & 0x7f);
+ tm->tm_hour = rs5c_reg2hr(rs5c, rs5c->regs[RS5C372_REG_HOURS]);
- tm->tm_sec = BCD2BIN(buf[RS5C372_REG_SECS] & 0x7f);
- tm->tm_min = BCD2BIN(buf[RS5C372_REG_MINS] & 0x7f);
- tm->tm_hour = BCD2BIN(buf[RS5C372_REG_HOURS] & 0x3f);
- tm->tm_wday = BCD2BIN(buf[RS5C372_REG_WDAY] & 0x07);
- tm->tm_mday = BCD2BIN(buf[RS5C372_REG_DAY] & 0x3f);
+ tm->tm_wday = BCD2BIN(rs5c->regs[RS5C372_REG_WDAY] & 0x07);
+ tm->tm_mday = BCD2BIN(rs5c->regs[RS5C372_REG_DAY] & 0x3f);
/* tm->tm_mon is zero-based */
- tm->tm_mon = BCD2BIN(buf[RS5C372_REG_MONTH] & 0x1f) - 1;
+ tm->tm_mon = BCD2BIN(rs5c->regs[RS5C372_REG_MONTH] & 0x1f) - 1;
/* year is 1900 + tm->tm_year */
- tm->tm_year = BCD2BIN(buf[RS5C372_REG_YEAR]) + 100;
+ tm->tm_year = BCD2BIN(rs5c->regs[RS5C372_REG_YEAR]) + 100;
dev_dbg(&client->dev, "%s: tm is secs=%d, mins=%d, hours=%d, "
"mday=%d, mon=%d, year=%d, wday=%d\n",
- __FUNCTION__,
+ __func__,
tm->tm_sec, tm->tm_min, tm->tm_hour,
tm->tm_mday, tm->tm_mon, tm->tm_year, tm->tm_wday);
- return 0;
+ /* rtc might need initialization */
+ return rtc_valid_tm(tm);
}
static int rs5c372_set_datetime(struct i2c_client *client, struct rtc_time *tm)
{
- unsigned char buf[8] = { RS5C372_REG_BASE };
+ struct rs5c372 *rs5c = i2c_get_clientdata(client);
+ unsigned char buf[8];
- dev_dbg(&client->dev,
- "%s: secs=%d, mins=%d, hours=%d "
+ dev_dbg(&client->dev, "%s: tm is secs=%d, mins=%d, hours=%d "
"mday=%d, mon=%d, year=%d, wday=%d\n",
- __FUNCTION__, tm->tm_sec, tm->tm_min, tm->tm_hour,
+ __func__,
+ tm->tm_sec, tm->tm_min, tm->tm_hour,
tm->tm_mday, tm->tm_mon, tm->tm_year, tm->tm_wday);
+ buf[0] = RS5C_ADDR(RS5C372_REG_SECS);
buf[1] = BIN2BCD(tm->tm_sec);
buf[2] = BIN2BCD(tm->tm_min);
- buf[3] = BIN2BCD(tm->tm_hour);
+ buf[3] = rs5c_hr2reg(rs5c, tm->tm_hour);
buf[4] = BIN2BCD(tm->tm_wday);
buf[5] = BIN2BCD(tm->tm_mday);
buf[6] = BIN2BCD(tm->tm_mon + 1);
buf[7] = BIN2BCD(tm->tm_year - 100);
if ((i2c_master_send(client, buf, 8)) != 8) {
- dev_err(&client->dev, "%s: write error\n", __FUNCTION__);
+ dev_err(&client->dev, "%s: write error\n", __func__);
return -EIO;
}
return 0;
}
+#if defined(CONFIG_RTC_INTF_PROC) || defined(CONFIG_RTC_INTF_PROC_MODULE)
+#define NEED_TRIM
+#endif
+
+#if defined(CONFIG_RTC_INTF_SYSFS) || defined(CONFIG_RTC_INTF_SYSFS_MODULE)
+#define NEED_TRIM
+#endif
+
+#ifdef NEED_TRIM
static int rs5c372_get_trim(struct i2c_client *client, int *osc, int *trim)
{
struct rs5c372 *rs5c372 = i2c_get_clientdata(client);
- u8 tmp = rs5c372->regs[RS5C372_REG_TRIM + 1];
+ u8 tmp = rs5c372->regs[RS5C372_REG_TRIM];
if (osc)
*osc = (tmp & RS5C372_TRIM_XSL) ? 32000 : 32768;
if (trim) {
- *trim = tmp & RS5C372_TRIM_MASK;
- dev_dbg(&client->dev, "%s: raw trim=%x\n", __FUNCTION__, *trim);
+ dev_dbg(&client->dev, "%s: raw trim=%x\n", __func__, tmp);
+ tmp &= RS5C372_TRIM_MASK;
+ if (tmp & 0x3e) {
+ int t = tmp & 0x3f;
+
+ if (tmp & 0x40)
+ t = (~t | (s8)0xc0) + 1;
+ else
+ t = t - 1;
+
+ tmp = t * 2;
+ } else
+ tmp = 0;
+ *trim = tmp;
}
return 0;
}
+#endif
static int rs5c372_rtc_read_time(struct device *dev, struct rtc_time *tm)
{
return rs5c372_set_datetime(to_i2c_client(dev), tm);
}
+#if defined(CONFIG_RTC_INTF_DEV) || defined(CONFIG_RTC_INTF_DEV_MODULE)
+
+static int
+rs5c_rtc_ioctl(struct device *dev, unsigned int cmd, unsigned long arg)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct rs5c372 *rs5c = i2c_get_clientdata(client);
+ unsigned char buf[2];
+ int status;
+
+ buf[1] = rs5c->regs[RS5C_REG_CTRL1];
+ switch (cmd) {
+ case RTC_UIE_OFF:
+ case RTC_UIE_ON:
+ /* some 327a modes use a different IRQ pin for 1Hz irqs */
+ if (rs5c->type == rtc_rs5c372a
+ && (buf[1] & RS5C372A_CTRL1_SL1))
+ return -ENOIOCTLCMD;
+ case RTC_AIE_OFF:
+ case RTC_AIE_ON:
+ /* these irq management calls only make sense for chips
+ * which are wired up to an IRQ.
+ */
+ if (!rs5c->has_irq)
+ return -ENOIOCTLCMD;
+ break;
+ default:
+ return -ENOIOCTLCMD;
+ }
+
+ status = rs5c_get_regs(rs5c);
+ if (status < 0)
+ return status;
+
+ buf[0] = RS5C_ADDR(RS5C_REG_CTRL1);
+ switch (cmd) {
+ case RTC_AIE_OFF: /* alarm off */
+ buf[1] &= ~RS5C_CTRL1_AALE;
+ break;
+ case RTC_AIE_ON: /* alarm on */
+ buf[1] |= RS5C_CTRL1_AALE;
+ break;
+ case RTC_UIE_OFF: /* update off */
+ buf[1] &= ~RS5C_CTRL1_CT_MASK;
+ break;
+ case RTC_UIE_ON: /* update on */
+ buf[1] &= ~RS5C_CTRL1_CT_MASK;
+ buf[1] |= RS5C_CTRL1_CT4;
+ break;
+ }
+ if ((i2c_master_send(client, buf, 2)) != 2) {
+ printk(KERN_WARNING "%s: can't update alarm\n",
+ rs5c->rtc->name);
+ status = -EIO;
+ } else
+ rs5c->regs[RS5C_REG_CTRL1] = buf[1];
+ return status;
+}
+
+#else
+#define rs5c_rtc_ioctl NULL
+#endif
+
+
+/* NOTE: Since RTC_WKALM_{RD,SET} were originally defined for EFI,
+ * which only exposes a polled programming interface; and since
+ * these calls map directly to those EFI requests; we don't demand
+ * we have an IRQ for this chip when we go through this API.
+ *
+ * The older x86_pc derived RTC_ALM_{READ,SET} calls require irqs
+ * though, managed through RTC_AIE_{ON,OFF} requests.
+ */
+
+static int rs5c_read_alarm(struct device *dev, struct rtc_wkalrm *t)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct rs5c372 *rs5c = i2c_get_clientdata(client);
+ int status;
+
+ status = rs5c_get_regs(rs5c);
+ if (status < 0)
+ return status;
+
+ /* report alarm time */
+ t->time.tm_sec = 0;
+ t->time.tm_min = BCD2BIN(rs5c->regs[RS5C_REG_ALARM_A_MIN] & 0x7f);
+ t->time.tm_hour = rs5c_reg2hr(rs5c, rs5c->regs[RS5C_REG_ALARM_A_HOURS]);
+ t->time.tm_mday = -1;
+ t->time.tm_mon = -1;
+ t->time.tm_year = -1;
+ t->time.tm_wday = -1;
+ t->time.tm_yday = -1;
+ t->time.tm_isdst = -1;
+
+ /* ... and status */
+ t->enabled = !!(rs5c->regs[RS5C_REG_CTRL1] & RS5C_CTRL1_AALE);
+ t->pending = !!(rs5c->regs[RS5C_REG_CTRL2] & RS5C_CTRL2_AAFG);
+
+ return 0;
+}
+
+static int rs5c_set_alarm(struct device *dev, struct rtc_wkalrm *t)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct rs5c372 *rs5c = i2c_get_clientdata(client);
+ int status;
+ unsigned char buf[4];
+
+ /* only handle up to 24 hours in the future, like RTC_ALM_SET */
+ if (t->time.tm_mday != -1
+ || t->time.tm_mon != -1
+ || t->time.tm_year != -1)
+ return -EINVAL;
+
+ /* REVISIT: round up tm_sec */
+
+ /* if needed, disable irq (clears pending status) */
+ status = rs5c_get_regs(rs5c);
+ if (status < 0)
+ return status;
+ if (rs5c->regs[RS5C_REG_CTRL1] & RS5C_CTRL1_AALE) {
+ buf[0] = RS5C_ADDR(RS5C_REG_CTRL1);
+ buf[1] = rs5c->regs[RS5C_REG_CTRL1] & ~RS5C_CTRL1_AALE;
+ if (i2c_master_send(client, buf, 2) != 2) {
+ pr_debug("%s: can't disable alarm\n", rs5c->rtc->name);
+ return -EIO;
+ }
+ rs5c->regs[RS5C_REG_CTRL1] = buf[1];
+ }
+
+ /* set alarm */
+ buf[0] = RS5C_ADDR(RS5C_REG_ALARM_A_MIN);
+ buf[1] = BIN2BCD(t->time.tm_min);
+ buf[2] = rs5c_hr2reg(rs5c, t->time.tm_hour);
+ buf[3] = 0x7f; /* any/all days */
+ if ((i2c_master_send(client, buf, 4)) != 4) {
+ pr_debug("%s: can't set alarm time\n", rs5c->rtc->name);
+ return -EIO;
+ }
+
+ /* ... and maybe enable its irq */
+ if (t->enabled) {
+ buf[0] = RS5C_ADDR(RS5C_REG_CTRL1);
+ buf[1] = rs5c->regs[RS5C_REG_CTRL1] | RS5C_CTRL1_AALE;
+ if ((i2c_master_send(client, buf, 2)) != 2)
+ printk(KERN_WARNING "%s: can't enable alarm\n",
+ rs5c->rtc->name);
+ rs5c->regs[RS5C_REG_CTRL1] = buf[1];
+ }
+
+ return 0;
+}
+
+#if defined(CONFIG_RTC_INTF_PROC) || defined(CONFIG_RTC_INTF_PROC_MODULE)
+
static int rs5c372_rtc_proc(struct device *dev, struct seq_file *seq)
{
int err, osc, trim;
err = rs5c372_get_trim(to_i2c_client(dev), &osc, &trim);
if (err == 0) {
- seq_printf(seq, "%d.%03d KHz\n", osc / 1000, osc % 1000);
- seq_printf(seq, "trim\t: %d\n", trim);
+ seq_printf(seq, "crystal\t\t: %d.%03d KHz\n",
+ osc / 1000, osc % 1000);
+ seq_printf(seq, "trim\t\t: %d\n", trim);
}
return 0;
}
+#else
+#define rs5c372_rtc_proc NULL
+#endif
+
static const struct rtc_class_ops rs5c372_rtc_ops = {
.proc = rs5c372_rtc_proc,
+ .ioctl = rs5c_rtc_ioctl,
.read_time = rs5c372_rtc_read_time,
.set_time = rs5c372_rtc_set_time,
+ .read_alarm = rs5c_read_alarm,
+ .set_alarm = rs5c_set_alarm,
};
+#if defined(CONFIG_RTC_INTF_SYSFS) || defined(CONFIG_RTC_INTF_SYSFS_MODULE)
+
static ssize_t rs5c372_sysfs_show_trim(struct device *dev,
struct device_attribute *attr, char *buf)
{
if (err)
return err;
- return sprintf(buf, "0x%2x\n", trim);
+ return sprintf(buf, "%d\n", trim);
}
static DEVICE_ATTR(trim, S_IRUGO, rs5c372_sysfs_show_trim, NULL);
}
static DEVICE_ATTR(osc, S_IRUGO, rs5c372_sysfs_show_osc, NULL);
-static int rs5c372_attach(struct i2c_adapter *adapter)
+static int rs5c_sysfs_register(struct device *dev)
+{
+ int err;
+
+ err = device_create_file(dev, &dev_attr_trim);
+ if (err)
+ return err;
+ err = device_create_file(dev, &dev_attr_osc);
+ if (err)
+ device_remove_file(dev, &dev_attr_trim);
+
+ return err;
+}
+
+static void rs5c_sysfs_unregister(struct device *dev)
{
- return i2c_probe(adapter, &addr_data, rs5c372_probe);
+ device_remove_file(dev, &dev_attr_trim);
+ device_remove_file(dev, &dev_attr_osc);
}
-static int rs5c372_probe(struct i2c_adapter *adapter, int address, int kind)
+#else
+static int rs5c_sysfs_register(struct device *dev)
+{
+ return 0;
+}
+
+static void rs5c_sysfs_unregister(struct device *dev)
+{
+ /* nothing */
+}
+#endif /* SYSFS */
+
+static struct i2c_driver rs5c372_driver;
+
+static int rs5c372_probe(struct i2c_client *client)
{
int err = 0;
- struct i2c_client *client;
struct rs5c372 *rs5c372;
+ struct rtc_time tm;
- dev_dbg(adapter->class_dev.dev, "%s\n", __FUNCTION__);
+ dev_dbg(&client->dev, "%s\n", __func__);
- if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) {
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
err = -ENODEV;
goto exit;
}
err = -ENOMEM;
goto exit;
}
- client = &rs5c372->client;
- /* I2C client */
- client->addr = address;
- client->driver = &rs5c372_driver;
- client->adapter = adapter;
+ rs5c372->client = client;
+ i2c_set_clientdata(client, rs5c372);
- strlcpy(client->name, rs5c372_driver.driver.name, I2C_NAME_SIZE);
+ /* we read registers 0x0f then 0x00-0x0f; skip the first one */
+ rs5c372->regs = &rs5c372->buf[1];
- i2c_set_clientdata(client, rs5c372);
+ err = rs5c_get_regs(rs5c372);
+ if (err < 0)
+ goto exit_kfree;
- rs5c372->msg[0].addr = address;
- rs5c372->msg[0].flags = I2C_M_RD;
- rs5c372->msg[0].len = sizeof(rs5c372->regs);
- rs5c372->msg[0].buf = rs5c372->regs;
+ if (strcmp(client->name, "rs5c372a") == 0)
+ rs5c372->type = rtc_rs5c372a;
+ else if (strcmp(client->name, "rs5c372b") == 0)
+ rs5c372->type = rtc_rs5c372b;
+ else if (strcmp(client->name, "rv5c386") == 0)
+ rs5c372->type = rtc_rv5c386;
+ else if (strcmp(client->name, "rv5c387a") == 0)
+ rs5c372->type = rtc_rv5c387a;
+ else {
+ rs5c372->type = rtc_rs5c372b;
+ dev_warn(&client->dev, "assuming rs5c372b\n");
+ }
- /* Inform the i2c layer */
- if ((err = i2c_attach_client(client)))
+ /* clock may be set for am/pm or 24 hr time */
+ switch (rs5c372->type) {
+ case rtc_rs5c372a:
+ case rtc_rs5c372b:
+ /* alarm uses ALARM_A; and nINTRA on 372a, nINTR on 372b.
+ * so does periodic irq, except some 327a modes.
+ */
+ if (rs5c372->regs[RS5C_REG_CTRL2] & RS5C372_CTRL2_24)
+ rs5c372->time24 = 1;
+ break;
+ case rtc_rv5c386:
+ case rtc_rv5c387a:
+ if (rs5c372->regs[RS5C_REG_CTRL1] & RV5C387_CTRL1_24)
+ rs5c372->time24 = 1;
+ /* alarm uses ALARM_W; and nINTRB for alarm and periodic
+ * irq, on both 386 and 387
+ */
+ break;
+ default:
+ dev_err(&client->dev, "unknown RTC type\n");
goto exit_kfree;
+ }
+
+ /* if the oscillator lost power and no other software (like
+ * the bootloader) set it up, do it here.
+ */
+ if (rs5c372->regs[RS5C_REG_CTRL2] & RS5C_CTRL2_XSTP) {
+ unsigned char buf[3];
+
+ rs5c372->regs[RS5C_REG_CTRL2] &= ~RS5C_CTRL2_XSTP;
+
+ buf[0] = RS5C_ADDR(RS5C_REG_CTRL1);
+ buf[1] = rs5c372->regs[RS5C_REG_CTRL1];
+ buf[2] = rs5c372->regs[RS5C_REG_CTRL2];
+
+ /* use 24hr mode */
+ switch (rs5c372->type) {
+ case rtc_rs5c372a:
+ case rtc_rs5c372b:
+ buf[2] |= RS5C372_CTRL2_24;
+ rs5c372->time24 = 1;
+ break;
+ case rtc_rv5c386:
+ case rtc_rv5c387a:
+ buf[1] |= RV5C387_CTRL1_24;
+ rs5c372->time24 = 1;
+ break;
+ default:
+ /* impossible */
+ break;
+ }
+
+ if ((i2c_master_send(client, buf, 3)) != 3) {
+ dev_err(&client->dev, "setup error\n");
+ goto exit_kfree;
+ }
+ rs5c372->regs[RS5C_REG_CTRL1] = buf[1];
+ rs5c372->regs[RS5C_REG_CTRL2] = buf[2];
+ }
- dev_info(&client->dev, "chip found, driver version " DRV_VERSION "\n");
+ if (rs5c372_get_datetime(client, &tm) < 0)
+ dev_warn(&client->dev, "clock needs to be set\n");
+
+ dev_info(&client->dev, "%s found, %s, driver version " DRV_VERSION "\n",
+ ({ char *s; switch (rs5c372->type) {
+ case rtc_rs5c372a: s = "rs5c372a"; break;
+ case rtc_rs5c372b: s = "rs5c372b"; break;
+ case rtc_rv5c386: s = "rv5c386"; break;
+ case rtc_rv5c387a: s = "rv5c387a"; break;
+ default: s = "chip"; break;
+ }; s;}),
+ rs5c372->time24 ? "24hr" : "am/pm"
+ );
+
+ /* REVISIT use client->irq to register alarm irq ... */
rs5c372->rtc = rtc_device_register(rs5c372_driver.driver.name,
&client->dev, &rs5c372_rtc_ops, THIS_MODULE);
if (IS_ERR(rs5c372->rtc)) {
err = PTR_ERR(rs5c372->rtc);
- goto exit_detach;
+ goto exit_kfree;
}
- err = device_create_file(&client->dev, &dev_attr_trim);
+ err = rs5c_sysfs_register(&client->dev);
if (err)
goto exit_devreg;
- err = device_create_file(&client->dev, &dev_attr_osc);
- if (err)
- goto exit_trim;
return 0;
-exit_trim:
- device_remove_file(&client->dev, &dev_attr_trim);
-
exit_devreg:
rtc_device_unregister(rs5c372->rtc);
-exit_detach:
- i2c_detach_client(client);
-
exit_kfree:
kfree(rs5c372);
return err;
}
-static int rs5c372_detach(struct i2c_client *client)
+static int rs5c372_remove(struct i2c_client *client)
{
- int err;
struct rs5c372 *rs5c372 = i2c_get_clientdata(client);
- if (rs5c372->rtc)
- rtc_device_unregister(rs5c372->rtc);
-
- if ((err = i2c_detach_client(client)))
- return err;
-
+ rtc_device_unregister(rs5c372->rtc);
+ rs5c_sysfs_unregister(&client->dev);
kfree(rs5c372);
return 0;
}
+static struct i2c_driver rs5c372_driver = {
+ .driver = {
+ .name = "rtc-rs5c372",
+ },
+ .probe = rs5c372_probe,
+ .remove = rs5c372_remove,
+};
+
static __init int rs5c372_init(void)
{
return i2c_add_driver(&rs5c372_driver);