#define ENE_TEST_C9 0xc9 /* 8bit */
#define ENE_TEST_C9_TLTENABLE 0x02
-#ifdef CONFIG_CARDBUS
-
/*
* Texas Instruments CardBus controller overrides.
*/
}
}
+
+/* Returns true value if the second slot of a two-slot controller is empty */
+static int ti12xx_2nd_slot_empty(struct yenta_socket *socket)
+{
+ struct pci_dev *func;
+ struct yenta_socket *slot2;
+ int devfn;
+ unsigned int state;
+ int ret = 1;
+
+ /* catch the two-slot controllers */
+ switch (socket->dev->device) {
+ case PCI_DEVICE_ID_TI_1220:
+ case PCI_DEVICE_ID_TI_1221:
+ case PCI_DEVICE_ID_TI_1225:
+ case PCI_DEVICE_ID_TI_1251A:
+ case PCI_DEVICE_ID_TI_1251B:
+ case PCI_DEVICE_ID_TI_1420:
+ case PCI_DEVICE_ID_TI_1450:
+ case PCI_DEVICE_ID_TI_1451A:
+ case PCI_DEVICE_ID_TI_1520:
+ case PCI_DEVICE_ID_TI_1620:
+ case PCI_DEVICE_ID_TI_4520:
+ case PCI_DEVICE_ID_TI_4450:
+ case PCI_DEVICE_ID_TI_4451:
+ /*
+ * there are way more, but they need to be added in yenta_socket.c
+ * and pci_ids.h first anyway.
+ */
+ break;
+
+ /* single-slot controllers have the 2nd slot empty always :) */
+ default:
+ return 1;
+ }
+
+ /* get other slot */
+ devfn = socket->dev->devfn & ~0x07;
+ func = pci_get_slot(socket->dev->bus,
+ (socket->dev->devfn & 0x07) ? devfn : devfn | 0x01);
+ if (!func)
+ return 1;
+
+ slot2 = pci_get_drvdata(func);
+ if (!slot2)
+ goto out;
+
+ /* check state */
+ yenta_get_status(&socket->socket, &state);
+ if (state & SS_DETECT) {
+ ret = 0;
+ goto out;
+ }
+
+out:
+ pci_dev_put(func);
+ return ret;
+}
+
+/*
+ * TI specifiy parts for the power hook.
+ *
+ * some TI's with some CB's produces interrupt storm on power on. it has been
+ * seen with atheros wlan cards on TI1225 and TI1410. solution is simply to
+ * disable any CB interrupts during this time.
+ */
+static int ti12xx_power_hook(struct pcmcia_socket *sock, int operation)
+{
+ struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
+ u32 mfunc, devctl, sysctl;
+ u8 gpio3;
+
+ /* only POWER_PRE and POWER_POST are interesting */
+ if ((operation != HOOK_POWER_PRE) && (operation != HOOK_POWER_POST))
+ return 0;
+
+ devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
+ sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
+ mfunc = config_readl(socket, TI122X_MFUNC);
+
+ /*
+ * all serial/tied: only disable when modparm set. always doing it
+ * would mean a regression for working setups 'cos it disables the
+ * interrupts for both both slots on 2-slot controllers
+ * (and users of single slot controllers where it's save have to
+ * live with setting the modparm, most don't have to anyway)
+ */
+ if (((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) &&
+ (pwr_irqs_off || ti12xx_2nd_slot_empty(socket))) {
+ switch (socket->dev->device) {
+ case PCI_DEVICE_ID_TI_1250:
+ case PCI_DEVICE_ID_TI_1251A:
+ case PCI_DEVICE_ID_TI_1251B:
+ case PCI_DEVICE_ID_TI_1450:
+ case PCI_DEVICE_ID_TI_1451A:
+ case PCI_DEVICE_ID_TI_4450:
+ case PCI_DEVICE_ID_TI_4451:
+ /* these chips have no IRQSER setting in MFUNC3 */
+ break;
+
+ default:
+ if (operation == HOOK_POWER_PRE)
+ mfunc = (mfunc & ~TI122X_MFUNC3_MASK);
+ else
+ mfunc = (mfunc & ~TI122X_MFUNC3_MASK) | TI122X_MFUNC3_IRQSER;
+ }
+
+ return 0;
+ }
+
+ /* do the job differently for func0/1 */
+ if ((PCI_FUNC(socket->dev->devfn) == 0) ||
+ ((sysctl & TI122X_SCR_INTRTIE) &&
+ (pwr_irqs_off || ti12xx_2nd_slot_empty(socket)))) {
+ /* some bridges are different */
+ switch (socket->dev->device) {
+ case PCI_DEVICE_ID_TI_1250:
+ case PCI_DEVICE_ID_TI_1251A:
+ case PCI_DEVICE_ID_TI_1251B:
+ case PCI_DEVICE_ID_TI_1450:
+ /* those oldies use gpio3 for INTA */
+ gpio3 = config_readb(socket, TI1250_GPIO3_CONTROL);
+ if (operation == HOOK_POWER_PRE)
+ gpio3 = (gpio3 & ~TI1250_GPIO_MODE_MASK) | 0x40;
+ else
+ gpio3 &= ~TI1250_GPIO_MODE_MASK;
+ config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3);
+ break;
+
+ default:
+ /* all new bridges are the same */
+ if (operation == HOOK_POWER_PRE)
+ mfunc &= ~TI122X_MFUNC0_MASK;
+ else
+ mfunc |= TI122X_MFUNC0_INTA;
+ config_writel(socket, TI122X_MFUNC, mfunc);
+ }
+ } else {
+ switch (socket->dev->device) {
+ case PCI_DEVICE_ID_TI_1251A:
+ case PCI_DEVICE_ID_TI_1251B:
+ case PCI_DEVICE_ID_TI_1450:
+ /* those have INTA elsewhere and INTB in MFUNC0 */
+ if (operation == HOOK_POWER_PRE)
+ mfunc &= ~TI122X_MFUNC0_MASK;
+ else
+ mfunc |= TI125X_MFUNC0_INTB;
+ config_writel(socket, TI122X_MFUNC, mfunc);
+
+ break;
+
+ default:
+ /* all new bridges are the same */
+ if (operation == HOOK_POWER_PRE)
+ mfunc &= ~TI122X_MFUNC1_MASK;
+ else
+ mfunc |= TI122X_MFUNC1_INTB;
+ config_writel(socket, TI122X_MFUNC, mfunc);
+ }
+ }
+
+ return 0;
+}
+
static int ti12xx_override(struct yenta_socket *socket)
{
u32 val, val_orig;
else
ti12xx_irqroute_func1(socket);
+ /* install power hook */
+ socket->socket.power_hook = ti12xx_power_hook;
+
return ti_override(socket);
}
return ti12xx_override(socket);
}
-#endif /* CONFIG_CARDBUS */
-
#endif /* _LINUX_TI113X_H */
projects / linux-2.6 / blobdiff