pci_write_config_byte(pdev, 0xa, 6);
pci_write_config_byte(pdev, 0x40, tmp);
- pdev->class = 0x010601;
+ pdev->class = PCI_CLASS_STORAGE_SATA_AHCI;
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_sb600_sata);
* bridge. Unfortunately, this device has no subvendor/subdevice ID. So it
* becomes necessary to do this tweak in two steps -- I've chosen the Host
* bridge as trigger.
+ *
+ * Note that we used to unhide the SMBus that way on Toshiba laptops
+ * (Satellite A40 and Tecra M2) but then found that the thermal management
+ * was done by SMM code, which could cause unsynchronized concurrent
+ * accesses to the SMBus registers, with potentially bad effects. Thus you
+ * should be very careful when adding new entries: if SMM is accessing the
+ * Intel SMBus, this is a very good reason to leave it hidden.
*/
static int asus_hides_smbus;
case 0x099c: /* HP Compaq nx6110 */
asus_hides_smbus = 1;
}
- } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_TOSHIBA)) {
- if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB)
- switch(dev->subsystem_device) {
- case 0x0001: /* Toshiba Satellite A40 */
- asus_hides_smbus = 1;
- }
- else if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
- switch(dev->subsystem_device) {
- case 0x0001: /* Toshiba Tecra M2 */
- asus_hides_smbus = 1;
- }
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) {
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch(dev->subsystem_device) {
* do this early on to make the additional device appear during
* the PCI scanning.
*/
-
-static void quirk_jmicron_dualfn(struct pci_dev *pdev)
+static void quirk_jmicron_ata(struct pci_dev *pdev)
{
- u32 conf;
+ u32 conf1, conf5, class;
u8 hdr;
/* Only poke fn 0 */
if (PCI_FUNC(pdev->devfn))
return;
- switch(pdev->device) {
- case PCI_DEVICE_ID_JMICRON_JMB365:
- case PCI_DEVICE_ID_JMICRON_JMB366:
- /* Redirect IDE second PATA port to the right spot */
- pci_read_config_dword(pdev, 0x80, &conf);
- conf |= (1 << 24);
- /* Fall through */
- pci_write_config_dword(pdev, 0x80, conf);
- case PCI_DEVICE_ID_JMICRON_JMB361:
- case PCI_DEVICE_ID_JMICRON_JMB363:
- pci_read_config_dword(pdev, 0x40, &conf);
- /* Enable dual function mode, AHCI on fn 0, IDE fn1 */
- /* Set the class codes correctly and then direct IDE 0 */
- conf &= ~0x000FF200; /* Clear bit 9 and 12-19 */
- conf |= 0x00C2A102; /* Set 1, 8, 13, 15, 17, 22, 23 */
- pci_write_config_dword(pdev, 0x40, conf);
-
- /* Reconfigure so that the PCI scanner discovers the
- device is now multifunction */
-
- pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr);
- pdev->hdr_type = hdr & 0x7f;
- pdev->multifunction = !!(hdr & 0x80);
+ pci_read_config_dword(pdev, 0x40, &conf1);
+ pci_read_config_dword(pdev, 0x80, &conf5);
- break;
+ conf1 &= ~0x00CFF302; /* Clear bit 1, 8, 9, 12-19, 22, 23 */
+ conf5 &= ~(1 << 24); /* Clear bit 24 */
+
+ switch (pdev->device) {
+ case PCI_DEVICE_ID_JMICRON_JMB360:
+ /* The controller should be in single function ahci mode */
+ conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */
+ break;
+
+ case PCI_DEVICE_ID_JMICRON_JMB365:
+ case PCI_DEVICE_ID_JMICRON_JMB366:
+ /* Redirect IDE second PATA port to the right spot */
+ conf5 |= (1 << 24);
+ /* Fall through */
+ case PCI_DEVICE_ID_JMICRON_JMB361:
+ case PCI_DEVICE_ID_JMICRON_JMB363:
+ /* Enable dual function mode, AHCI on fn 0, IDE fn1 */
+ /* Set the class codes correctly and then direct IDE 0 */
+ conf1 |= 0x00C2A102; /* Set 1, 8, 13, 15, 17, 22, 23 */
+ break;
+
+ case PCI_DEVICE_ID_JMICRON_JMB368:
+ /* The controller should be in single function IDE mode */
+ conf1 |= 0x00C00000; /* Set 22, 23 */
+ break;
}
-}
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, quirk_jmicron_dualfn);
-DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, quirk_jmicron_dualfn);
+
+ pci_write_config_dword(pdev, 0x40, conf1);
+ pci_write_config_dword(pdev, 0x80, conf5);
+
+ /* Update pdev accordingly */
+ pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr);
+ pdev->hdr_type = hdr & 0x7f;
+ pdev->multifunction = !!(hdr & 0x80);
+
+ pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class);
+ pdev->class = class >> 8;
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
#endif
*/
static void __devinit quirk_pcie_pxh(struct pci_dev *dev)
{
- disable_msi_mode(dev, pci_find_capability(dev, PCI_CAP_ID_MSI),
- PCI_CAP_ID_MSI);
+ pci_msi_off(dev);
+
dev->no_msi = 1;
printk(KERN_WARNING "PCI: PXH quirk detected, "
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm);
+/*
+ * Toshiba TC86C001 IDE controller reports the standard 8-byte BAR0 size
+ * but the PIO transfers won't work if BAR0 falls at the odd 8 bytes.
+ * Re-allocate the region if needed...
+ */
+static void __init quirk_tc86c001_ide(struct pci_dev *dev)
+{
+ struct resource *r = &dev->resource[0];
+
+ if (r->start & 0x8) {
+ r->start = 0;
+ r->end = 0xf;
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA_2,
+ PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE,
+ quirk_tc86c001_ide);
+
static void __devinit quirk_netmos(struct pci_dev *dev)
{
unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4;