* under either the MPL or the GPL. */
/*
- * v0.01 -> v0.02 - 21/3/2001 - Jean II
- * o Allow to use regular ethX device name instead of dldwdX
- * o Warning on IBSS with ESSID=any for firmware 6.06
- * o Put proper range.throughput values (optimistic)
- * o IWSPY support (IOCTL and stat gather in Rx path)
- * o Allow setting frequency in Ad-Hoc mode
- * o Disable WEP setting if !has_wep to work on old firmware
- * o Fix txpower range
- * o Start adding support for Samsung/Compaq firmware
- *
- * v0.02 -> v0.03 - 23/3/2001 - Jean II
- * o Start adding Symbol support - need to check all that
- * o Fix Prism2/Symbol WEP to accept 128 bits keys
- * o Add Symbol WEP (add authentication type)
- * o Add Prism2/Symbol rate
- * o Add PM timeout (holdover duration)
- * o Enable "iwconfig eth0 key off" and friends (toggle flags)
- * o Enable "iwconfig eth0 power unicast/all" (toggle flags)
- * o Try with an Intel card. It report firmware 1.01, behave like
- * an antiquated firmware, however on windows it says 2.00. Yuck !
- * o Workaround firmware bug in allocate buffer (Intel 1.01)
- * o Finish external renaming to orinoco...
- * o Testing with various Wavelan firmwares
- *
- * v0.03 -> v0.04 - 30/3/2001 - Jean II
- * o Update to Wireless 11 -> add retry limit/lifetime support
- * o Tested with a D-Link DWL 650 card, fill in firmware support
- * o Warning on Vcc mismatch (D-Link 3.3v card in Lucent 5v only slot)
- * o Fixed the Prism2 WEP bugs that I introduced in v0.03 :-(
- * It works on D-Link *only* after a tcpdump. Weird...
- * And still doesn't work on Intel card. Grrrr...
- * o Update the mode after a setport3
- * o Add preamble setting for Symbol cards (not yet enabled)
- * o Don't complain as much about Symbol cards...
- *
- * v0.04 -> v0.04b - 22/4/2001 - David Gibson
- * o Removed the 'eth' parameter - always use ethXX as the
- * interface name instead of dldwdXX. The other was racy
- * anyway.
- * o Clean up RID definitions in hermes.h, other cleanups
- *
- * v0.04b -> v0.04c - 24/4/2001 - Jean II
- * o Tim Hurley <timster AT seiki.bliztech.com> reported a D-Link card
- * with vendor 02 and firmware 0.08. Added in the capabilities...
- * o Tested Lucent firmware 7.28, everything works...
- *
- * v0.04c -> v0.05 - 3/5/2001 - Benjamin Herrenschmidt
- * o Spin-off Pcmcia code. This file is renamed orinoco.c,
- * and orinoco_cs.c now contains only the Pcmcia specific stuff
- * o Add Airport driver support on top of orinoco.c (see airport.c)
- *
- * v0.05 -> v0.05a - 4/5/2001 - Jean II
- * o Revert to old Pcmcia code to fix breakage of Ben's changes...
- *
- * v0.05a -> v0.05b - 4/5/2001 - Jean II
- * o add module parameter 'ignore_cis_vcc' for D-Link @ 5V
- * o D-Link firmware doesn't support multicast. We just print a few
- * error messages, but otherwise everything works...
- * o For David : set/getport3 works fine, just upgrade iwpriv...
- *
- * v0.05b -> v0.05c - 5/5/2001 - Benjamin Herrenschmidt
- * o Adapt airport.c to latest changes in orinoco.c
- * o Remove deferred power enabling code
- *
- * v0.05c -> v0.05d - 5/5/2001 - Jean II
- * o Workaround to SNAP decapsulate frame from Linksys AP
- * original patch from : Dong Liu <dliu AT research.bell-labs.com>
- * (note : the memcmp bug was mine - fixed)
- * o Remove set_retry stuff, no firmware support it (bloat--).
- *
- * v0.05d -> v0.06 - 25/5/2001 - Jean II
- * Original patch from "Hong Lin" <alin AT redhat.com>,
- * "Ian Kinner" <ikinner AT redhat.com>
- * and "David Smith" <dsmith AT redhat.com>
- * o Init of priv->tx_rate_ctrl in firmware specific section.
- * o Prism2/Symbol rate, upto should be 0xF and not 0x15. Doh !
- * o Spectrum card always need cor_reset (for every reset)
- * o Fix cor_reset to not lose bit 7 in the register
- * o flush_stale_links to remove zombie Pcmcia instances
- * o Ack previous hermes event before reset
- * Me (with my little hands)
- * o Allow orinoco.c to call cor_reset via priv->card_reset_handler
- * o Add priv->need_card_reset to toggle this feature
- * o Fix various buglets when setting WEP in Symbol firmware
- * Now, encryption is fully functional on Symbol cards. Youpi !
- *
- * v0.06 -> v0.06b - 25/5/2001 - Jean II
- * o IBSS on Symbol use port_mode = 4. Please don't ask...
- *
- * v0.06b -> v0.06c - 29/5/2001 - Jean II
- * o Show first spy address in /proc/net/wireless for IBSS mode as well
- *
- * v0.06c -> v0.06d - 6/7/2001 - David Gibson
- * o Change a bunch of KERN_INFO messages to KERN_DEBUG, as per Linus'
- * wishes to reduce the number of unnecessary messages.
- * o Removed bogus message on CRC error.
- * o Merged fixes for v0.08 Prism 2 firmware from William Waghorn
- * <willwaghorn AT yahoo.co.uk>
- * o Slight cleanup/re-arrangement of firmware detection code.
- *
- * v0.06d -> v0.06e - 1/8/2001 - David Gibson
- * o Removed some redundant global initializers (orinoco_cs.c).
- * o Added some module metadata
- *
- * v0.06e -> v0.06f - 14/8/2001 - David Gibson
- * o Wording fix to license
- * o Added a 'use_alternate_encaps' module parameter for APs which need an
- * oui of 00:00:00. We really need a better way of handling this, but
- * the module flag is better than nothing for now.
- *
- * v0.06f -> v0.07 - 20/8/2001 - David Gibson
- * o Removed BAP error retries from hermes_bap_seek(). For Tx we now
- * let the upper layers handle the retry, we retry explicitly in the
- * Rx path, but don't make as much noise about it.
- * o Firmware detection cleanups.
- *
- * v0.07 -> v0.07a - 1/10/3001 - Jean II
- * o Add code to read Symbol firmware revision, inspired by latest code
- * in Spectrum24 by Lee John Keyser-Allen - Thanks Lee !
- * o Thanks to Jared Valentine <hidden AT xmission.com> for "providing" me
- * a 3Com card with a recent firmware, fill out Symbol firmware
- * capabilities of latest rev (2.20), as well as older Symbol cards.
- * o Disable Power Management in newer Symbol firmware, the API
- * has changed (documentation needed).
- *
- * v0.07a -> v0.08 - 3/10/2001 - David Gibson
- * o Fixed a possible buffer overrun found by the Stanford checker (in
- * dldwd_ioctl_setiwencode()). Can only be called by root anyway, so not
- * a big problem.
- * o Turned has_big_wep on for Intersil cards. That's not true for all of
- * them but we should at least let the capable ones try.
- * o Wait for BUSY to clear at the beginning of hermes_bap_seek(). I
- * realized that my assumption that the driver's serialization
- * would prevent the BAP being busy on entry was possibly false, because
- * things other than seeks may make the BAP busy.
- * o Use "alternate" (oui 00:00:00) encapsulation by default.
- * Setting use_old_encaps will mimic the old behaviour, but I think we
- * will be able to eliminate this.
- * o Don't try to make __initdata const (the version string). This can't
- * work because of the way the __initdata sectioning works.
- * o Added MODULE_LICENSE tags.
- * o Support for PLX (transparent PCMCIA->PCI bridge) cards.
- * o Changed to using the new type-fascist min/max.
- *
- * v0.08 -> v0.08a - 9/10/2001 - David Gibson
- * o Inserted some missing acknowledgements/info into the Changelog.
- * o Fixed some bugs in the normalization of signal level reporting.
- * o Fixed bad bug in WEP key handling on Intersil and Symbol firmware,
- * which led to an instant crash on big-endian machines.
- *
- * v0.08a -> v0.08b - 20/11/2001 - David Gibson
- * o Lots of cleanup and bugfixes in orinoco_plx.c
- * o Cleanup to handling of Tx rate setting.
- * o Removed support for old encapsulation method.
- * o Removed old "dldwd" names.
- * o Split RID constants into a new file hermes_rid.h
- * o Renamed RID constants to match linux-wlan-ng and prism2.o
- * o Bugfixes in hermes.c
- * o Poke the PLX's INTCSR register, so it actually starts
- * generating interrupts. These cards might actually work now.
- * o Update to wireless extensions v12 (Jean II)
- * o Support for tallies and inquire command (Jean II)
- * o Airport updates for newer PPC kernels (BenH)
- *
- * v0.08b -> v0.09 - 21/12/2001 - David Gibson
- * o Some new PCI IDs for PLX cards.
- * o Removed broken attempt to do ALLMULTI reception. Just use
- * promiscuous mode instead
- * o Preliminary work for list-AP (Jean II)
- * o Airport updates from (BenH)
- * o Eliminated racy hw_ready stuff
- * o Fixed generation of fake events in irq handler. This should
- * finally kill the EIO problems (Jean II & dgibson)
- * o Fixed breakage of bitrate set/get on Agere firmware (Jean II)
- *
- * v0.09 -> v0.09a - 2/1/2002 - David Gibson
- * o Fixed stupid mistake in multicast list handling, triggering
- * a BUG()
- *
- * v0.09a -> v0.09b - 16/1/2002 - David Gibson
- * o Fixed even stupider mistake in new interrupt handling, which
- * seriously broke things on big-endian machines.
- * o Removed a bunch of redundant includes and exports.
- * o Removed a redundant MOD_{INC,DEC}_USE_COUNT pair in airport.c
- * o Don't attempt to do hardware level multicast reception on
- * Intersil firmware, just go promisc instead.
- * o Typo fixed in hermes_issue_cmd()
- * o Eliminated WIRELESS_SPY #ifdefs
- * o Status code reported on Tx exceptions
- * o Moved netif_wake_queue() from ALLOC interrupts to TX and TXEXC
- * interrupts, which should fix the timeouts we're seeing.
- *
- * v0.09b -> v0.10 - 25 Feb 2002 - David Gibson
- * o Removed nested structures used for header parsing, so the
- * driver should now work without hackery on ARM
- * o Fix for WEP handling on Intersil (Hawk Newton)
- * o Eliminated the /proc/hermes/ethXX/regs debugging file. It
- * was never very useful.
- * o Make Rx errors less noisy.
- *
- * v0.10 -> v0.11 - 5 Apr 2002 - David Gibson
- * o Laid the groundwork in hermes.[ch] for devices which map
- * into PCI memory space rather than IO space.
- * o Fixed bug in multicast handling (cleared multicast list when
- * leaving promiscuous mode).
- * o Relegated Tx error messages to debug.
- * o Cleaned up / corrected handling of allocation lengths.
- * o Set OWNSSID in IBSS mode for WinXP interoperability (jimc).
- * o Change to using alloc_etherdev() for structure allocations.
- * o Check for and drop undersized packets.
- * o Fixed a race in stopping/waking the queue. This should fix
- * the timeout problems (Pavel Roskin)
- * o Reverted to netif_wake_queue() on the ALLOC event.
- * o Fixes for recent Symbol firmwares which lack AP density
- * (Pavel Roskin).
- *
- * v0.11 -> v0.11a - 29 Apr 2002 - David Gibson
- * o Handle different register spacing, necessary for Prism 2.5
- * PCI adaptors (Steve Hill).
- * o Cleaned up initialization of card structures in orinoco_cs
- * and airport. Removed card->priv field.
- * o Make response structure optional for hermes_docmd_wait()
- * Pavel Roskin)
- * o Added PCI id for Nortel emobility to orinoco_plx.c.
- * o Cleanup to handling of Symbol's allocation bug. (Pavel Roskin)
- * o Cleanups to firmware capability detection.
- * o Arrange for orinoco_pci.c to override firmware detection.
- * We should be able to support the PCI Intersil cards now.
- * o Cleanup handling of reset_cor and hard_reset (Pavel Roskin).
- * o Remove erroneous use of USER_BAP in the TxExc handler (Jouni
- * Malinen).
- * o Makefile changes for better integration into David Hinds
- * pcmcia-cs package.
- *
- * v0.11a -> v0.11b - 1 May 2002 - David Gibson
- * o Better error reporting in orinoco_plx_init_one()
- * o Fixed multiple bad kfree() bugs introduced by the
- * alloc_orinocodev() changes.
- *
- * v0.11b -> v0.12 - 19 Jun 2002 - David Gibson
- * o Support changing the MAC address.
- * o Correct display of Intersil firmware revision numbers.
- * o Entirely revised locking scheme. Should be both simpler and
- * better.
- * o Merged some common code in orinoco_plx, orinoco_pci and
- * airport by creating orinoco_default_{open,stop,reset}()
- * which are used as the dev->open, dev->stop, priv->reset
- * callbacks if none are specified when alloc_orinocodev() is
- * called.
- * o Removed orinoco_plx_interrupt() and orinoco_pci_interrupt().
- * They didn't do anything.
- *
- * v0.12 -> v0.12a - 4 Jul 2002 - David Gibson
- * o Some rearrangement of code.
- * o Numerous fixups to locking and rest handling, particularly
- * for PCMCIA.
- * o This allows open and stop net_device methods to be in
- * orinoco.c now, rather than in the init modules.
- * o In orinoco_cs.c link->priv now points to the struct
- * net_device not to the struct orinoco_private.
- * o Added a check for undersized SNAP frames, which could cause
- * crashes.
- *
- * v0.12a -> v0.12b - 11 Jul 2002 - David Gibson
- * o Fix hw->num_init testing code, so num_init is actually
- * incremented.
- * o Fix very stupid bug in orinoco_cs which broke compile with
- * CONFIG_SMP.
- * o Squashed a warning.
- *
- * v0.12b -> v0.12c - 26 Jul 2002 - David Gibson
- * o Change to C9X style designated initializers.
- * o Add support for 3Com AirConnect PCI.
- * o No longer ignore the hard_reset argument to
- * alloc_orinocodev(). Oops.
- *
- * v0.12c -> v0.13beta1 - 13 Sep 2002 - David Gibson
- * o Revert the broken 0.12* locking scheme and go to a new yet
- * simpler scheme.
- * o Do firmware resets only in orinoco_init() and when waking
- * the card from hard sleep.
- *
- * v0.13beta1 -> v0.13 - 27 Sep 2002 - David Gibson
- * o Re-introduced full resets (via schedule_task()) on Tx
- * timeout.
- *
- * v0.13 -> v0.13a - 30 Sep 2002 - David Gibson
- * o Minor cleanups to info frame handling. Add basic support
- * for linkstatus info frames.
- * o Include required kernel headers in orinoco.h, to avoid
- * compile problems.
- *
- * v0.13a -> v0.13b - 10 Feb 2003 - David Gibson
- * o Implemented hard reset for Airport cards
- * o Experimental suspend/resume implementation for orinoco_pci
- * o Abolished /proc debugging support, replaced with a debugging
- * iwpriv. Now it's ugly and simple instead of ugly and complex.
- * o Bugfix in hermes.c if the firmware returned a record length
- * of 0, we could go clobbering memory.
- * o Bugfix in orinoco_stop() - it used to fail if hw_unavailable
- * was set, which was usually true on PCMCIA hot removes.
- * o Track LINKSTATUS messages, silently drop Tx packets before
- * we are connected (avoids confusing the firmware), and only
- * give LINKSTATUS printk()s if the status has changed.
- *
- * v0.13b -> v0.13c - 11 Mar 2003 - David Gibson
- * o Cleanup: use dev instead of priv in various places.
- * o Bug fix: Don't ReleaseConfiguration on RESET_PHYSICAL event
- * if we're in the middle of a (driver initiated) hard reset.
- * o Bug fix: ETH_ZLEN is supposed to include the header
- * (Dionysus Blazakis & Manish Karir)
- * o Convert to using workqueues instead of taskqueues (and
- * backwards compatibility macros for pre 2.5.41 kernels).
- * o Drop redundant (I think...) MOD_{INC,DEC}_USE_COUNT in
- * airport.c
- * o New orinoco_tmd.c init module from Joerg Dorchain for
- * TMD7160 based PCI to PCMCIA bridges (similar to
- * orinoco_plx.c).
- *
- * v0.13c -> v0.13d - 22 Apr 2003 - David Gibson
- * o Make hw_unavailable a counter, rather than just a flag, this
- * is necessary to avoid some races (such as a card being
- * removed in the middle of orinoco_reset().
- * o Restore Release/RequestConfiguration in the PCMCIA event handler
- * when dealing with a driver initiated hard reset. This is
- * necessary to prevent hangs due to a spurious interrupt while
- * the reset is in progress.
- * o Clear the 802.11 header when transmitting, even though we
- * don't use it. This fixes a long standing bug on some
- * firmwares, which seem to get confused if that isn't done.
- * o Be less eager to de-encapsulate SNAP frames, only do so if
- * the OUI is 00:00:00 or 00:00:f8, leave others alone. The old
- * behaviour broke CDP (Cisco Discovery Protocol).
- * o Use dev instead of priv for free_irq() as well as
- * request_irq() (oops).
- * o Attempt to reset rather than giving up if we get too many
- * IRQs.
- * o Changed semantics of __orinoco_down() so it can be called
- * safely with hw_unavailable set. It also now clears the
- * linkstatus (since we're going to have to reassociate).
- *
- * v0.13d -> v0.13e - 12 May 2003 - David Gibson
- * o Support for post-2.5.68 return values from irq handler.
- * o Fixed bug where underlength packets would be double counted
- * in the rx_dropped statistics.
- * o Provided a module parameter to suppress linkstatus messages.
- *
- * v0.13e -> v0.14alpha1 - 30 Sep 2003 - David Gibson
- * o Replaced priv->connected logic with netif_carrier_on/off()
- * calls.
- * o Remove has_ibss_any and never set the CREATEIBSS RID when
- * the ESSID is empty. Too many firmwares break if we do.
- * o 2.6 merges: Replace pdev->slot_name with pci_name(), remove
- * __devinitdata from PCI ID tables, use free_netdev().
- * o Enabled shared-key authentication for Agere firmware (from
- * Robert J. Moore <Robert.J.Moore AT allanbank.com>
- * o Move netif_wake_queue() (back) to the Tx completion from the
- * ALLOC event. This seems to prevent/mitigate the rolling
- * error -110 problems at least on some Intersil firmwares.
- * Theoretically reduces performance, but I can't measure it.
- * Patch from Andrew Tridgell <tridge AT samba.org>
- *
- * v0.14alpha1 -> v0.14alpha2 - 20 Oct 2003 - David Gibson
- * o Correctly turn off shared-key authentication when requested
- * (bugfix from Robert J. Moore).
- * o Correct airport sleep interfaces for current 2.6 kernels.
- * o Add code for key change without disabling/enabling the MAC
- * port. This is supposed to allow 802.1x to work sanely, but
- * doesn't seem to yet.
- *
* TODO
- * o New wireless extensions API (patch from Moustafa
- * Youssef, updated by Jim Carter and Pavel Roskin).
* o Handle de-encapsulation within network layer, provide 802.11
* headers (patch from Thomas 'Dent' Mirlacher)
- * o RF monitor mode support
* o Fix possible races in SPY handling.
* o Disconnect wireless extensions from fundamental configuration.
* o (maybe) Software WEP support (patch from Stano Meduna).
module_param(ignore_disconnect, int, 0644);
MODULE_PARM_DESC(ignore_disconnect, "Don't report lost link to the network layer");
+static int force_monitor; /* = 0 */
+module_param(force_monitor, int, 0644);
+MODULE_PARM_DESC(force_monitor, "Allow monitor mode for all firmware versions");
+
/********************************************************************/
/* Compile time configuration and compatibility stuff */
/********************************************************************/
u16 ethertype;
} __attribute__ ((packed));
+/* Rx frame header except compatibility 802.3 header */
struct hermes_rx_descriptor {
+ /* Control */
u16 status;
u32 time;
u8 silence;
u8 rate;
u8 rxflow;
u32 reserved;
+
+ /* 802.11 header */
+ u16 frame_ctl;
+ u16 duration_id;
+ u8 addr1[ETH_ALEN];
+ u8 addr2[ETH_ALEN];
+ u8 addr3[ETH_ALEN];
+ u16 seq_ctl;
+ u8 addr4[ETH_ALEN];
+
+ /* Data length */
+ u16 data_len;
} __attribute__ ((packed));
/********************************************************************/
priv->createibss = 1;
}
break;
+ case IW_MODE_MONITOR:
+ priv->port_type = 3;
+ priv->createibss = 0;
+ break;
default:
printk(KERN_ERR "%s: Invalid priv->iw_mode in set_port_type()\n",
priv->ndev->name);
return 1;
}
- if (! netif_carrier_ok(dev)) {
+ if (! netif_carrier_ok(dev) || (priv->iw_mode == IW_MODE_MONITOR)) {
/* Oops, the firmware hasn't established a connection,
silently drop the packet (this seems to be the
safest approach). */
}
}
+/*
+ * orinoco_rx_monitor - handle received monitor frames.
+ *
+ * Arguments:
+ * dev network device
+ * rxfid received FID
+ * desc rx descriptor of the frame
+ *
+ * Call context: interrupt
+ */
+static void orinoco_rx_monitor(struct net_device *dev, u16 rxfid,
+ struct hermes_rx_descriptor *desc)
+{
+ u32 hdrlen = 30; /* return full header by default */
+ u32 datalen = 0;
+ u16 fc;
+ int err;
+ int len;
+ struct sk_buff *skb;
+ struct orinoco_private *priv = netdev_priv(dev);
+ struct net_device_stats *stats = &priv->stats;
+ hermes_t *hw = &priv->hw;
+
+ len = le16_to_cpu(desc->data_len);
+
+ /* Determine the size of the header and the data */
+ fc = le16_to_cpu(desc->frame_ctl);
+ switch (fc & IEEE80211_FCTL_FTYPE) {
+ case IEEE80211_FTYPE_DATA:
+ if ((fc & IEEE80211_FCTL_TODS)
+ && (fc & IEEE80211_FCTL_FROMDS))
+ hdrlen = 30;
+ else
+ hdrlen = 24;
+ datalen = len;
+ break;
+ case IEEE80211_FTYPE_MGMT:
+ hdrlen = 24;
+ datalen = len;
+ break;
+ case IEEE80211_FTYPE_CTL:
+ switch (fc & IEEE80211_FCTL_STYPE) {
+ case IEEE80211_STYPE_PSPOLL:
+ case IEEE80211_STYPE_RTS:
+ case IEEE80211_STYPE_CFEND:
+ case IEEE80211_STYPE_CFENDACK:
+ hdrlen = 16;
+ break;
+ case IEEE80211_STYPE_CTS:
+ case IEEE80211_STYPE_ACK:
+ hdrlen = 10;
+ break;
+ }
+ break;
+ default:
+ /* Unknown frame type */
+ break;
+ }
+
+ /* sanity check the length */
+ if (datalen > IEEE80211_DATA_LEN + 12) {
+ printk(KERN_DEBUG "%s: oversized monitor frame, "
+ "data length = %d\n", dev->name, datalen);
+ err = -EIO;
+ stats->rx_length_errors++;
+ goto update_stats;
+ }
+
+ skb = dev_alloc_skb(hdrlen + datalen);
+ if (!skb) {
+ printk(KERN_WARNING "%s: Cannot allocate skb for monitor frame\n",
+ dev->name);
+ err = -ENOMEM;
+ goto drop;
+ }
+
+ /* Copy the 802.11 header to the skb */
+ memcpy(skb_put(skb, hdrlen), &(desc->frame_ctl), hdrlen);
+ skb->mac.raw = skb->data;
+
+ /* If any, copy the data from the card to the skb */
+ if (datalen > 0) {
+ err = hermes_bap_pread(hw, IRQ_BAP, skb_put(skb, datalen),
+ ALIGN(datalen, 2), rxfid,
+ HERMES_802_2_OFFSET);
+ if (err) {
+ printk(KERN_ERR "%s: error %d reading monitor frame\n",
+ dev->name, err);
+ goto drop;
+ }
+ }
+
+ skb->dev = dev;
+ skb->ip_summed = CHECKSUM_NONE;
+ skb->pkt_type = PACKET_OTHERHOST;
+ skb->protocol = __constant_htons(ETH_P_802_2);
+
+ dev->last_rx = jiffies;
+ stats->rx_packets++;
+ stats->rx_bytes += skb->len;
+
+ netif_rx(skb);
+ return;
+
+ drop:
+ dev_kfree_skb_irq(skb);
+ update_stats:
+ stats->rx_errors++;
+ stats->rx_dropped++;
+}
+
static void __orinoco_ev_rx(struct net_device *dev, hermes_t *hw)
{
struct orinoco_private *priv = netdev_priv(dev);
struct net_device_stats *stats = &priv->stats;
struct iw_statistics *wstats = &priv->wstats;
struct sk_buff *skb = NULL;
- u16 rxfid, status;
- int length, data_len, data_off;
- char *p;
+ u16 rxfid, status, fc;
+ int length;
struct hermes_rx_descriptor desc;
- struct header_struct hdr;
- struct ethhdr *eh;
+ struct ethhdr *hdr;
int err;
rxfid = hermes_read_regn(hw, RXFID);
if (err) {
printk(KERN_ERR "%s: error %d reading Rx descriptor. "
"Frame dropped.\n", dev->name, err);
- stats->rx_errors++;
- goto drop;
+ goto update_stats;
}
status = le16_to_cpu(desc.status);
- if (status & HERMES_RXSTAT_ERR) {
- if (status & HERMES_RXSTAT_UNDECRYPTABLE) {
- wstats->discard.code++;
- DEBUG(1, "%s: Undecryptable frame on Rx. Frame dropped.\n",
- dev->name);
- } else {
- stats->rx_crc_errors++;
- DEBUG(1, "%s: Bad CRC on Rx. Frame dropped.\n", dev->name);
- }
- stats->rx_errors++;
- goto drop;
+ if (status & HERMES_RXSTAT_BADCRC) {
+ DEBUG(1, "%s: Bad CRC on Rx. Frame dropped.\n",
+ dev->name);
+ stats->rx_crc_errors++;
+ goto update_stats;
}
- /* For now we ignore the 802.11 header completely, assuming
- that the card's firmware has handled anything vital */
+ /* Handle frames in monitor mode */
+ if (priv->iw_mode == IW_MODE_MONITOR) {
+ orinoco_rx_monitor(dev, rxfid, &desc);
+ return;
+ }
- err = hermes_bap_pread(hw, IRQ_BAP, &hdr, sizeof(hdr),
- rxfid, HERMES_802_3_OFFSET);
- if (err) {
- printk(KERN_ERR "%s: error %d reading frame header. "
- "Frame dropped.\n", dev->name, err);
- stats->rx_errors++;
- goto drop;
+ if (status & HERMES_RXSTAT_UNDECRYPTABLE) {
+ DEBUG(1, "%s: Undecryptable frame on Rx. Frame dropped.\n",
+ dev->name);
+ wstats->discard.code++;
+ goto update_stats;
}
- length = ntohs(hdr.len);
-
+ length = le16_to_cpu(desc.data_len);
+ fc = le16_to_cpu(desc.frame_ctl);
+
/* Sanity checks */
if (length < 3) { /* No for even an 802.2 LLC header */
/* At least on Symbol firmware with PCF we get quite a
lot of these legitimately - Poll frames with no
data. */
- stats->rx_dropped++;
- goto drop;
+ return;
}
if (length > IEEE802_11_DATA_LEN) {
printk(KERN_WARNING "%s: Oversized frame received (%d bytes)\n",
dev->name, length);
stats->rx_length_errors++;
- stats->rx_errors++;
- goto drop;
+ goto update_stats;
}
/* We need space for the packet data itself, plus an ethernet
if (!skb) {
printk(KERN_WARNING "%s: Can't allocate skb for Rx\n",
dev->name);
- goto drop;
+ goto update_stats;
}
- skb_reserve(skb, 2); /* This way the IP header is aligned */
+ /* We'll prepend the header, so reserve space for it. The worst
+ case is no decapsulation, when 802.3 header is prepended and
+ nothing is removed. 2 is for aligning the IP header. */
+ skb_reserve(skb, ETH_HLEN + 2);
+
+ err = hermes_bap_pread(hw, IRQ_BAP, skb_put(skb, length),
+ ALIGN(length, 2), rxfid,
+ HERMES_802_2_OFFSET);
+ if (err) {
+ printk(KERN_ERR "%s: error %d reading frame. "
+ "Frame dropped.\n", dev->name, err);
+ goto drop;
+ }
/* Handle decapsulation
* In most cases, the firmware tell us about SNAP frames.
* For some reason, the SNAP frames sent by LinkSys APs
* are not properly recognised by most firmwares.
* So, check ourselves */
- if (((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_1042) ||
- ((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_TUNNEL) ||
- is_ethersnap(&hdr)) {
+ if (length >= ENCAPS_OVERHEAD &&
+ (((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_1042) ||
+ ((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_TUNNEL) ||
+ is_ethersnap(skb->data))) {
/* These indicate a SNAP within 802.2 LLC within
802.11 frame which we'll need to de-encapsulate to
the original EthernetII frame. */
-
- if (length < ENCAPS_OVERHEAD) { /* No room for full LLC+SNAP */
- stats->rx_length_errors++;
- goto drop;
- }
-
- /* Remove SNAP header, reconstruct EthernetII frame */
- data_len = length - ENCAPS_OVERHEAD;
- data_off = HERMES_802_3_OFFSET + sizeof(hdr);
-
- eh = (struct ethhdr *)skb_put(skb, ETH_HLEN);
-
- memcpy(eh, &hdr, 2 * ETH_ALEN);
- eh->h_proto = hdr.ethertype;
+ hdr = (struct ethhdr *)skb_push(skb, ETH_HLEN - ENCAPS_OVERHEAD);
} else {
- /* All other cases indicate a genuine 802.3 frame. No
- decapsulation needed. We just throw the whole
- thing in, and hope the protocol layer can deal with
- it as 802.3 */
- data_len = length;
- data_off = HERMES_802_3_OFFSET;
- /* FIXME: we re-read from the card data we already read here */
- }
-
- p = skb_put(skb, data_len);
- err = hermes_bap_pread(hw, IRQ_BAP, p, ALIGN(data_len, 2),
- rxfid, data_off);
- if (err) {
- printk(KERN_ERR "%s: error %d reading frame. "
- "Frame dropped.\n", dev->name, err);
- stats->rx_errors++;
- goto drop;
+ /* 802.3 frame - prepend 802.3 header as is */
+ hdr = (struct ethhdr *)skb_push(skb, ETH_HLEN);
+ hdr->h_proto = htons(length);
}
+ memcpy(hdr->h_dest, desc.addr1, ETH_ALEN);
+ if (fc & IEEE80211_FCTL_FROMDS)
+ memcpy(hdr->h_source, desc.addr3, ETH_ALEN);
+ else
+ memcpy(hdr->h_source, desc.addr2, ETH_ALEN);
dev->last_rx = jiffies;
skb->dev = dev;
skb->protocol = eth_type_trans(skb, dev);
skb->ip_summed = CHECKSUM_NONE;
+ if (fc & IEEE80211_FCTL_TODS)
+ skb->pkt_type = PACKET_OTHERHOST;
/* Process the wireless stats if needed */
orinoco_stat_gather(dev, skb, &desc);
return;
drop:
+ dev_kfree_skb_irq(skb);
+ update_stats:
+ stats->rx_errors++;
stats->rx_dropped++;
-
- if (skb)
- dev_kfree_skb_irq(skb);
- return;
}
/********************************************************************/
u16 newstatus;
int connected;
+ if (priv->iw_mode == IW_MODE_MONITOR)
+ break;
+
if (len != sizeof(linkstatus)) {
printk(KERN_WARNING "%s: Unexpected size for linkstatus frame (%d bytes)\n",
dev->name, len);
}
}
+ if (priv->iw_mode == IW_MODE_MONITOR) {
+ /* Enable monitor mode */
+ dev->type = ARPHRD_IEEE80211;
+ err = hermes_docmd_wait(hw, HERMES_CMD_TEST |
+ HERMES_TEST_MONITOR, 0, NULL);
+ } else {
+ /* Disable monitor mode */
+ dev->type = ARPHRD_ETHER;
+ err = hermes_docmd_wait(hw, HERMES_CMD_TEST |
+ HERMES_TEST_STOP, 0, NULL);
+ }
+ if (err)
+ return err;
+
/* Set promiscuity / multicast*/
priv->promiscuous = 0;
priv->mc_count = 0;
priv->has_pm = (firmver >= 0x40020); /* Don't work in 7.52 ? */
priv->ibss_port = 1;
priv->has_hostscan = (firmver >= 0x8000a);
+ priv->broken_monitor = (firmver >= 0x80000);
/* Tested with Agere firmware :
* 1.16 ; 4.08 ; 4.52 ; 6.04 ; 6.16 ; 7.28 => Jean II
case IW_MODE_INFRA:
break;
+ case IW_MODE_MONITOR:
+ if (priv->broken_monitor && !force_monitor) {
+ printk(KERN_WARNING "%s: Monitor mode support is "
+ "buggy in this firmware, not enabling\n",
+ dev->name);
+ err = -EOPNOTSUPP;
+ }
+ break;
+
default:
err = -EOPNOTSUPP;
break;
unsigned long flags;
int err = -EINPROGRESS; /* Call commit handler */
- /* We can only use this in Ad-Hoc demo mode to set the operating
- * frequency, or in IBSS mode to set the frequency where the IBSS
- * will be created - Jean II */
- if (priv->iw_mode != IW_MODE_ADHOC)
- return -EOPNOTSUPP;
+ /* In infrastructure mode the AP sets the channel */
+ if (priv->iw_mode == IW_MODE_INFRA)
+ return -EBUSY;
if ( (frq->e == 0) && (frq->m <= 1000) ) {
/* Setting by channel number */
if (orinoco_lock(priv, &flags) != 0)
return -EBUSY;
+
priv->channel = chan;
+ if (priv->iw_mode == IW_MODE_MONITOR) {
+ /* Fast channel change - no commit if successful */
+ hermes_t *hw = &priv->hw;
+ err = hermes_docmd_wait(hw, HERMES_CMD_TEST |
+ HERMES_TEST_SET_CHANNEL,
+ chan, NULL);
+ }
orinoco_unlock(priv, &flags);
return err;
projects / linux-2.6 / blobdiff