#define VS
#endif
-#define IWLWIFI_VERSION "1.2.22k" VD VS
+#define IWLWIFI_VERSION "1.2.23k" VD VS
#define DRV_COPYRIGHT "Copyright(c) 2003-2007 Intel Corporation"
#define DRV_VERSION IWLWIFI_VERSION
BUG_ON((fix_size > TFD_MAX_PAYLOAD_SIZE) &&
!(cmd->meta.flags & CMD_SIZE_HUGE));
+
+ if (iwl3945_is_rfkill(priv)) {
+ IWL_DEBUG_INFO("Not sending command - RF KILL");
+ return -EIO;
+ }
+
if (iwl3945_queue_space(q) < ((cmd->meta.flags & CMD_ASYNC) ? 2 : 1)) {
IWL_ERROR("No space for Tx\n");
return -ENOSPC;
memcpy(mac, priv->eeprom.mac_address, 6);
}
+/*
+ * Clear the OWNER_MSK, to establish driver (instead of uCode running on
+ * embedded controller) as EEPROM reader; each read is a series of pulses
+ * to/from the EEPROM chip, not a single event, so even reads could conflict
+ * if they weren't arbitrated by some ownership mechanism. Here, the driver
+ * simply claims ownership, which should be safe when this function is called
+ * (i.e. before loading uCode!).
+ */
+static inline int iwl3945_eeprom_acquire_semaphore(struct iwl3945_priv *priv)
+{
+ _iwl3945_clear_bit(priv, CSR_EEPROM_GP, CSR_EEPROM_GP_IF_OWNER_MSK);
+ return 0;
+}
+
/**
* iwl3945_eeprom_init - read EEPROM contents
*
*/
int iwl3945_eeprom_init(struct iwl3945_priv *priv)
{
- __le16 *e = (__le16 *)&priv->eeprom;
+ u16 *e = (u16 *)&priv->eeprom;
u32 gp = iwl3945_read32(priv, CSR_EEPROM_GP);
u32 r;
int sz = sizeof(priv->eeprom);
IWL_ERROR("Time out reading EEPROM[%d]", addr);
return -ETIMEDOUT;
}
- e[addr / 2] = cpu_to_le16(r >> 16);
+ e[addr / 2] = le16_to_cpu((__force __le16)(r >> 16));
}
return 0;
#endif
/* drop all data frame if we are not associated */
- if (!iwl3945_is_associated(priv) && !priv->assoc_id &&
+ if ((!iwl3945_is_associated(priv) ||
+ ((priv->iw_mode == IEEE80211_IF_TYPE_STA) && !priv->assoc_id)) &&
((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_DATA)) {
IWL_DEBUG_DROP("Dropping - !iwl3945_is_associated\n");
goto drop_unlock;
* Conversion assumes that levels are voltages (20*log), not powers (10*log). */
int iwl3945_calc_db_from_ratio(int sig_ratio)
{
- /* Anything above 1000:1 just report as 60 dB */
- if (sig_ratio > 1000)
+ /* 1000:1 or higher just report as 60 dB */
+ if (sig_ratio >= 1000)
return 60;
- /* Above 100:1, divide by 10 and use table,
+ /* 100:1 or higher, divide by 10 and use table,
* add 20 dB to make up for divide by 10 */
- if (sig_ratio > 100)
+ if (sig_ratio >= 100)
return (20 + (int)ratio2dB[sig_ratio/10]);
/* We shouldn't see this */
int reclaim;
unsigned long flags;
u8 fill_rx = 0;
- u32 count = 0;
+ u32 count = 8;
/* uCode's read index (stored in shared DRAM) indicates the last Rx
* buffer that the driver may process (last buffer filled by ucode). */
#ifdef CONFIG_IWL3945_DEBUG
if (iwl3945_debug_level & (IWL_DL_ISR)) {
/* NIC fires this, but we don't use it, redundant with WAKEUP */
- if (inta & CSR_INT_BIT_MAC_CLK_ACTV)
- IWL_DEBUG_ISR("Microcode started or stopped.\n");
+ if (inta & CSR_INT_BIT_SCD)
+ IWL_DEBUG_ISR("Scheduler finished to transmit "
+ "the frame/frames.\n");
/* Alive notification via Rx interrupt will do the real work */
if (inta & CSR_INT_BIT_ALIVE)
}
#endif
/* Safely ignore these bits for debug checks below */
- inta &= ~(CSR_INT_BIT_MAC_CLK_ACTV | CSR_INT_BIT_ALIVE);
+ inta &= ~(CSR_INT_BIT_SCD | CSR_INT_BIT_ALIVE);
/* HW RF KILL switch toggled (4965 only) */
if (inta & CSR_INT_BIT_RF_KILL) {
IWL_DEBUG_ISR("ISR inta 0x%08x, enabled 0x%08x, fh 0x%08x\n",
inta, inta_mask, inta_fh);
+ inta &= ~CSR_INT_BIT_SCD;
+
/* iwl3945_irq_tasklet() will service interrupts and re-enable them */
- tasklet_schedule(&priv->irq_tasklet);
+ if (likely(inta || inta_fh))
+ tasklet_schedule(&priv->irq_tasklet);
unplugged:
spin_unlock(&priv->lock);
return 0;
}
+/*
+ * iwl3945_free_channel_map - undo allocations in iwl3945_init_channel_map
+ */
+static void iwl3945_free_channel_map(struct iwl3945_priv *priv)
+{
+ kfree(priv->channel_info);
+ priv->channel_count = 0;
+}
+
/* For active scan, listen ACTIVE_DWELL_TIME (msec) on each channel after
* sending probe req. This should be set long enough to hear probe responses
* from more than one AP. */
scan_ch->tpc.tx_gain = ((1 << 5) | (5 << 3));
/* NOTE: if we were doing 6Mb OFDM for scans we'd use
* power level:
- * scan_ch->tpc.tx_gain = ((1<<5) | (2 << 3)) | 3;
+ * scan_ch->tpc.tx_gain = ((1 << 5) | (2 << 3)) | 3;
*/
}
return 0;
}
+/*
+ * iwl3945_free_geos - undo allocations in iwl3945_init_geos
+ */
+static void iwl3945_free_geos(struct iwl3945_priv *priv)
+{
+ kfree(priv->modes);
+ kfree(priv->ieee_channels);
+ kfree(priv->ieee_rates);
+ clear_bit(STATUS_GEO_CONFIGURED, &priv->status);
+}
+
/******************************************************************************
*
* uCode download functions
static void iwl3945_dealloc_ucode_pci(struct iwl3945_priv *priv)
{
- if (priv->ucode_code.v_addr != NULL) {
- pci_free_consistent(priv->pci_dev,
- priv->ucode_code.len,
- priv->ucode_code.v_addr,
- priv->ucode_code.p_addr);
- priv->ucode_code.v_addr = NULL;
- }
- if (priv->ucode_data.v_addr != NULL) {
- pci_free_consistent(priv->pci_dev,
- priv->ucode_data.len,
- priv->ucode_data.v_addr,
- priv->ucode_data.p_addr);
- priv->ucode_data.v_addr = NULL;
- }
- if (priv->ucode_data_backup.v_addr != NULL) {
- pci_free_consistent(priv->pci_dev,
- priv->ucode_data_backup.len,
- priv->ucode_data_backup.v_addr,
- priv->ucode_data_backup.p_addr);
- priv->ucode_data_backup.v_addr = NULL;
- }
- if (priv->ucode_init.v_addr != NULL) {
- pci_free_consistent(priv->pci_dev,
- priv->ucode_init.len,
- priv->ucode_init.v_addr,
- priv->ucode_init.p_addr);
- priv->ucode_init.v_addr = NULL;
- }
- if (priv->ucode_init_data.v_addr != NULL) {
- pci_free_consistent(priv->pci_dev,
- priv->ucode_init_data.len,
- priv->ucode_init_data.v_addr,
- priv->ucode_init_data.p_addr);
- priv->ucode_init_data.v_addr = NULL;
- }
- if (priv->ucode_boot.v_addr != NULL) {
- pci_free_consistent(priv->pci_dev,
- priv->ucode_boot.len,
- priv->ucode_boot.v_addr,
- priv->ucode_boot.p_addr);
- priv->ucode_boot.v_addr = NULL;
- }
+ iwl_free_fw_desc(priv->pci_dev, &priv->ucode_code);
+ iwl_free_fw_desc(priv->pci_dev, &priv->ucode_data);
+ iwl_free_fw_desc(priv->pci_dev, &priv->ucode_data_backup);
+ iwl_free_fw_desc(priv->pci_dev, &priv->ucode_init);
+ iwl_free_fw_desc(priv->pci_dev, &priv->ucode_init_data);
+ iwl_free_fw_desc(priv->pci_dev, &priv->ucode_boot);
}
/**
iwl3945_write32(priv, CSR_RESET, 0);
}
-static int iwl3945_alloc_fw_desc(struct pci_dev *pci_dev, struct fw_desc *desc)
-{
- desc->v_addr = pci_alloc_consistent(pci_dev, desc->len, &desc->p_addr);
- return (desc->v_addr != NULL) ? 0 : -ENOMEM;
-}
-
/**
* iwl3945_read_ucode - Read uCode images from disk file.
*
* 1) unmodified from disk
* 2) backup cache for save/restore during power-downs */
priv->ucode_code.len = inst_size;
- iwl3945_alloc_fw_desc(priv->pci_dev, &priv->ucode_code);
+ iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_code);
priv->ucode_data.len = data_size;
- iwl3945_alloc_fw_desc(priv->pci_dev, &priv->ucode_data);
+ iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_data);
priv->ucode_data_backup.len = data_size;
- iwl3945_alloc_fw_desc(priv->pci_dev, &priv->ucode_data_backup);
+ iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_data_backup);
if (!priv->ucode_code.v_addr || !priv->ucode_data.v_addr ||
!priv->ucode_data_backup.v_addr)
/* Initialization instructions and data */
if (init_size && init_data_size) {
priv->ucode_init.len = init_size;
- iwl3945_alloc_fw_desc(priv->pci_dev, &priv->ucode_init);
+ iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_init);
priv->ucode_init_data.len = init_data_size;
- iwl3945_alloc_fw_desc(priv->pci_dev, &priv->ucode_init_data);
+ iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_init_data);
if (!priv->ucode_init.v_addr || !priv->ucode_init_data.v_addr)
goto err_pci_alloc;
/* Bootstrap (instructions only, no data) */
if (boot_size) {
priv->ucode_boot.len = boot_size;
- iwl3945_alloc_fw_desc(priv->pci_dev, &priv->ucode_boot);
+ iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_boot);
if (!priv->ucode_boot.v_addr)
goto err_pci_alloc;
/* Clear out the uCode error bit if it is set */
clear_bit(STATUS_FW_ERROR, &priv->status);
- rc = iwl3945_init_channel_map(priv);
- if (rc) {
- IWL_ERROR("initializing regulatory failed: %d\n", rc);
- return;
- }
-
- iwl3945_init_geos(priv);
- iwl3945_reset_channel_flag(priv);
-
if (iwl3945_is_rfkill(priv))
return;
STATUS_RF_KILL_HW |
test_bit(STATUS_RF_KILL_SW, &priv->status) <<
STATUS_RF_KILL_SW |
+ test_bit(STATUS_GEO_CONFIGURED, &priv->status) <<
+ STATUS_GEO_CONFIGURED |
test_bit(STATUS_IN_SUSPEND, &priv->status) <<
STATUS_IN_SUSPEND;
goto exit;
STATUS_RF_KILL_HW |
test_bit(STATUS_RF_KILL_SW, &priv->status) <<
STATUS_RF_KILL_SW |
+ test_bit(STATUS_GEO_CONFIGURED, &priv->status) <<
+ STATUS_GEO_CONFIGURED |
test_bit(STATUS_IN_SUSPEND, &priv->status) <<
STATUS_IN_SUSPEND |
test_bit(STATUS_FW_ERROR, &priv->status) <<
if (test_bit(STATUS_RF_KILL_SW, &priv->status)) {
IWL_WARNING("Radio disabled by SW RF kill (module "
"parameter)\n");
- return 0;
+ return -ENODEV;
}
if (!priv->ucode_data_backup.v_addr || !priv->ucode_data.v_addr) {
return -EIO;
}
+ /* If platform's RF_KILL switch is NOT set to KILL */
+ if (iwl3945_read32(priv, CSR_GP_CNTRL) &
+ CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW)
+ clear_bit(STATUS_RF_KILL_HW, &priv->status);
+ else {
+ set_bit(STATUS_RF_KILL_HW, &priv->status);
+ if (!test_bit(STATUS_IN_SUSPEND, &priv->status)) {
+ IWL_WARNING("Radio disabled by HW RF Kill switch\n");
+ return -ENODEV;
+ }
+ }
+
iwl3945_write32(priv, CSR_INT, 0xFFFFFFFF);
rc = iwl3945_hw_nic_init(priv);
memcpy(priv->ucode_data_backup.v_addr, priv->ucode_data.v_addr,
priv->ucode_data.len);
+ /* We return success when we resume from suspend and rf_kill is on. */
+ if (test_bit(STATUS_RF_KILL_HW, &priv->status))
+ return 0;
+
for (i = 0; i < MAX_HW_RESTARTS; i++) {
iwl3945_clear_stations_table(priv);
* that based on the direct_mask added to each channel entry */
scan->tx_cmd.len = cpu_to_le16(
iwl3945_fill_probe_req(priv, (struct ieee80211_mgmt *)scan->data,
- IWL_MAX_SCAN_SIZE - sizeof(scan), 0));
+ IWL_MAX_SCAN_SIZE - sizeof(*scan), 0));
scan->tx_cmd.tx_flags = TX_CMD_FLG_SEQ_CTL_MSK;
scan->tx_cmd.sta_id = priv->hw_setting.bcast_sta_id;
scan->tx_cmd.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE;
}
}
- IWL_DEBUG_INFO("Start UP work.\n");
- __iwl3945_up(priv);
+ ret = __iwl3945_up(priv);
- priv->is_open = 1;
mutex_unlock(&priv->mutex);
+ if (ret)
+ goto out_release_irq;
+
+ IWL_DEBUG_INFO("Start UP work.\n");
+
+ if (test_bit(STATUS_IN_SUSPEND, &priv->status))
+ return 0;
+
/* Wait for START_ALIVE from ucode. Otherwise callbacks from
* mac80211 will not be run successfully. */
ret = wait_event_interruptible_timeout(priv->wait_command_queue,
}
}
+ priv->is_open = 1;
IWL_DEBUG_MAC80211("leave\n");
return 0;
free_irq(priv->pci_dev->irq, priv);
out_disable_msi:
pci_disable_msi(priv->pci_dev);
+ pci_disable_device(priv->pci_dev);
+ priv->is_open = 0;
+ IWL_DEBUG_MAC80211("leave - failed\n");
return ret;
}
IWL_DEBUG_MAC80211("enter\n");
- /* stop mac, cancel any scan request and clear
- * RXON_FILTER_ASSOC_MSK BIT
- */
+ if (!priv->is_open) {
+ IWL_DEBUG_MAC80211("leave - skip\n");
+ return;
+ }
+
priv->is_open = 0;
if (iwl3945_is_ready_rf(priv)) {
+ /* stop mac, cancel any scan request and clear
+ * RXON_FILTER_ASSOC_MSK BIT
+ */
mutex_lock(&priv->mutex);
iwl3945_scan_cancel_timeout(priv, 100);
cancel_delayed_work(&priv->post_associate);
{
int rc = 0;
- if (priv->status & STATUS_EXIT_PENDING)
+ if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
/* The following should be done only at AP bring up */
mutex_unlock(&priv->mutex);
IWL_DEBUG_MAC80211("leave\n");
-
}
static int iwl3945_mac_hw_scan(struct ieee80211_hw *hw, u8 *ssid, size_t len)
IWL_DEBUG_INFO("MAC address: %s\n", print_mac(mac, priv->mac_addr));
SET_IEEE80211_PERM_ADDR(priv->hw, priv->mac_addr);
+ err = iwl3945_init_channel_map(priv);
+ if (err) {
+ IWL_ERROR("initializing regulatory failed: %d\n", err);
+ goto out_remove_sysfs;
+ }
+
+ err = iwl3945_init_geos(priv);
+ if (err) {
+ IWL_ERROR("initializing geos failed: %d\n", err);
+ goto out_free_channel_map;
+ }
+ iwl3945_reset_channel_flag(priv);
+
iwl3945_rate_control_register(priv->hw);
err = ieee80211_register_hw(priv->hw);
if (err) {
IWL_ERROR("Failed to register network device (error %d)\n", err);
- goto out_remove_sysfs;
+ goto out_free_geos;
}
priv->hw->conf.beacon_int = 100;
return 0;
+ out_free_geos:
+ iwl3945_free_geos(priv);
+ out_free_channel_map:
+ iwl3945_free_channel_map(priv);
out_remove_sysfs:
sysfs_remove_group(&pdev->dev.kobj, &iwl3945_attribute_group);
pci_disable_device(pdev);
pci_set_drvdata(pdev, NULL);
- kfree(priv->channel_info);
-
- kfree(priv->ieee_channels);
- kfree(priv->ieee_rates);
+ iwl3945_free_channel_map(priv);
+ iwl3945_free_geos(priv);
if (priv->ibss_beacon)
dev_kfree_skb(priv->ibss_beacon);
{
struct iwl3945_priv *priv = pci_get_drvdata(pdev);
- set_bit(STATUS_IN_SUSPEND, &priv->status);
-
- /* Take down the device; powers it off, etc. */
- iwl3945_down(priv);
-
- if (priv->mac80211_registered)
- ieee80211_stop_queues(priv->hw);
+ if (priv->is_open) {
+ set_bit(STATUS_IN_SUSPEND, &priv->status);
+ iwl3945_mac_stop(priv->hw);
+ priv->is_open = 1;
+ }
- pci_save_state(pdev);
- pci_disable_device(pdev);
pci_set_power_state(pdev, PCI_D3hot);
return 0;
}
-static void iwl3945_resume(struct iwl3945_priv *priv)
-{
- unsigned long flags;
-
- /* The following it a temporary work around due to the
- * suspend / resume not fully initializing the NIC correctly.
- * Without all of the following, resume will not attempt to take
- * down the NIC (it shouldn't really need to) and will just try
- * and bring the NIC back up. However that fails during the
- * ucode verification process. This then causes iwl3945_down to be
- * called *after* iwl3945_hw_nic_init() has succeeded -- which
- * then lets the next init sequence succeed. So, we've
- * replicated all of that NIC init code here... */
-
- iwl3945_write32(priv, CSR_INT, 0xFFFFFFFF);
-
- iwl3945_hw_nic_init(priv);
-
- iwl3945_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
- iwl3945_write32(priv, CSR_UCODE_DRV_GP1_CLR,
- CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
- iwl3945_write32(priv, CSR_INT, 0xFFFFFFFF);
- iwl3945_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
- iwl3945_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
-
- /* tell the device to stop sending interrupts */
- iwl3945_disable_interrupts(priv);
-
- spin_lock_irqsave(&priv->lock, flags);
- iwl3945_clear_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ);
-
- if (!iwl3945_grab_nic_access(priv)) {
- iwl3945_write_prph(priv, APMG_CLK_DIS_REG,
- APMG_CLK_VAL_DMA_CLK_RQT);
- iwl3945_release_nic_access(priv);
- }
- spin_unlock_irqrestore(&priv->lock, flags);
-
- udelay(5);
-
- iwl3945_hw_nic_reset(priv);
-
- /* Bring the device back up */
- clear_bit(STATUS_IN_SUSPEND, &priv->status);
- queue_work(priv->workqueue, &priv->up);
-}
-
static int iwl3945_pci_resume(struct pci_dev *pdev)
{
struct iwl3945_priv *priv = pci_get_drvdata(pdev);
- int err;
-
- printk(KERN_INFO "Coming out of suspend...\n");
pci_set_power_state(pdev, PCI_D0);
- err = pci_enable_device(pdev);
- pci_restore_state(pdev);
-
- /*
- * Suspend/Resume resets the PCI configuration space, so we have to
- * re-disable the RETRY_TIMEOUT register (0x41) to keep PCI Tx retries
- * from interfering with C3 CPU state. pci_restore_state won't help
- * here since it only restores the first 64 bytes pci config header.
- */
- pci_write_config_byte(pdev, 0x41, 0x00);
- iwl3945_resume(priv);
+ if (priv->is_open)
+ iwl3945_mac_start(priv->hw);
+ clear_bit(STATUS_IN_SUSPEND, &priv->status);
return 0;
}
projects / linux-2.6 / blobdiff