#ifndef __iwl_4965_hw_h__
#define __iwl_4965_hw_h__
+/*
+ * uCode queue management definitions ...
+ * Queue #4 is the command queue for 3945 and 4965; map it to Tx FIFO chnl 4.
+ * The first queue used for block-ack aggregation is #7 (4965 only).
+ * All block-ack aggregation queues should map to Tx DMA/FIFO channel 7.
+ */
+#define IWL_CMD_QUEUE_NUM 4
+#define IWL_CMD_FIFO_NUM 4
+#define IWL_BACK_QUEUE_FIRST_ID 7
+
+/* Tx rates */
+#define IWL_CCK_RATES 4
+#define IWL_OFDM_RATES 8
+
+#define IWL_HT_RATES 16
+
+#define IWL_MAX_RATES (IWL_CCK_RATES+IWL_OFDM_RATES+IWL_HT_RATES)
+
+/* Time constants */
+#define SHORT_SLOT_TIME 9
+#define LONG_SLOT_TIME 20
+
+/* RSSI to dBm */
+#define IWL_RSSI_OFFSET 44
+
+/*
+ * EEPROM related constants, enums, and structures.
+ */
+
+/*
+ * EEPROM access time values:
+ *
+ * Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG,
+ * then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit
+ * CSR_EEPROM_REG_BIT_CMD (0x2).
+ * Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1).
+ * When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec.
+ * Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG.
+ */
+#define IWL_EEPROM_ACCESS_TIMEOUT 5000 /* uSec */
+#define IWL_EEPROM_ACCESS_DELAY 10 /* uSec */
+
+/*
+ * Regulatory channel usage flags in EEPROM struct iwl4965_eeprom_channel.flags.
+ *
+ * IBSS and/or AP operation is allowed *only* on those channels with
+ * (VALID && IBSS && ACTIVE && !RADAR). This restriction is in place because
+ * RADAR detection is not supported by the 4965 driver, but is a
+ * requirement for establishing a new network for legal operation on channels
+ * requiring RADAR detection or restricting ACTIVE scanning.
+ *
+ * NOTE: "WIDE" flag does not indicate anything about "FAT" 40 MHz channels.
+ * It only indicates that 20 MHz channel use is supported; FAT channel
+ * usage is indicated by a separate set of regulatory flags for each
+ * FAT channel pair.
+ *
+ * NOTE: Using a channel inappropriately will result in a uCode error!
+ */
+enum {
+ EEPROM_CHANNEL_VALID = (1 << 0), /* usable for this SKU/geo */
+ EEPROM_CHANNEL_IBSS = (1 << 1), /* usable as an IBSS channel */
+ /* Bit 2 Reserved */
+ EEPROM_CHANNEL_ACTIVE = (1 << 3), /* active scanning allowed */
+ EEPROM_CHANNEL_RADAR = (1 << 4), /* radar detection required */
+ EEPROM_CHANNEL_WIDE = (1 << 5), /* 20 MHz channel okay */
+ EEPROM_CHANNEL_NARROW = (1 << 6), /* 10 MHz channel (not used) */
+ EEPROM_CHANNEL_DFS = (1 << 7), /* dynamic freq selection candidate */
+};
+
+/* SKU Capabilities */
+#define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE (1 << 0)
+#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE (1 << 1)
+
+/* *regulatory* channel data format in eeprom, one for each channel.
+ * There are separate entries for FAT (40 MHz) vs. normal (20 MHz) channels. */
+struct iwl4965_eeprom_channel {
+ u8 flags; /* EEPROM_CHANNEL_* flags copied from EEPROM */
+ s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */
+} __attribute__ ((packed));
+
+/* 4965 has two radio transmitters (and 3 radio receivers) */
+#define EEPROM_TX_POWER_TX_CHAINS (2)
+
+/* 4965 has room for up to 8 sets of txpower calibration data */
+#define EEPROM_TX_POWER_BANDS (8)
+
+/* 4965 factory calibration measures txpower gain settings for
+ * each of 3 target output levels */
+#define EEPROM_TX_POWER_MEASUREMENTS (3)
+
+/* 4965 driver does not work with txpower calibration version < 5.
+ * Look for this in calib_version member of struct iwl4965_eeprom. */
+#define EEPROM_TX_POWER_VERSION_NEW (5)
+
+
+/*
+ * 4965 factory calibration data for one txpower level, on one channel,
+ * measured on one of the 2 tx chains (radio transmitter and associated
+ * antenna). EEPROM contains:
+ *
+ * 1) Temperature (degrees Celsius) of device when measurement was made.
+ *
+ * 2) Gain table index used to achieve the target measurement power.
+ * This refers to the "well-known" gain tables (see iwl-4965-hw.h).
+ *
+ * 3) Actual measured output power, in half-dBm ("34" = 17 dBm).
+ *
+ * 4) RF power amplifier detector level measurement (not used).
+ */
+struct iwl4965_eeprom_calib_measure {
+ u8 temperature; /* Device temperature (Celsius) */
+ u8 gain_idx; /* Index into gain table */
+ u8 actual_pow; /* Measured RF output power, half-dBm */
+ s8 pa_det; /* Power amp detector level (not used) */
+} __attribute__ ((packed));
+
+
+/*
+ * 4965 measurement set for one channel. EEPROM contains:
+ *
+ * 1) Channel number measured
+ *
+ * 2) Measurements for each of 3 power levels for each of 2 radio transmitters
+ * (a.k.a. "tx chains") (6 measurements altogether)
+ */
+struct iwl4965_eeprom_calib_ch_info {
+ u8 ch_num;
+ struct iwl4965_eeprom_calib_measure measurements[EEPROM_TX_POWER_TX_CHAINS]
+ [EEPROM_TX_POWER_MEASUREMENTS];
+} __attribute__ ((packed));
+
+/*
+ * 4965 txpower subband info.
+ *
+ * For each frequency subband, EEPROM contains the following:
+ *
+ * 1) First and last channels within range of the subband. "0" values
+ * indicate that this sample set is not being used.
+ *
+ * 2) Sample measurement sets for 2 channels close to the range endpoints.
+ */
+struct iwl4965_eeprom_calib_subband_info {
+ u8 ch_from; /* channel number of lowest channel in subband */
+ u8 ch_to; /* channel number of highest channel in subband */
+ struct iwl4965_eeprom_calib_ch_info ch1;
+ struct iwl4965_eeprom_calib_ch_info ch2;
+} __attribute__ ((packed));
+
+
+/*
+ * 4965 txpower calibration info. EEPROM contains:
+ *
+ * 1) Factory-measured saturation power levels (maximum levels at which
+ * tx power amplifier can output a signal without too much distortion).
+ * There is one level for 2.4 GHz band and one for 5 GHz band. These
+ * values apply to all channels within each of the bands.
+ *
+ * 2) Factory-measured power supply voltage level. This is assumed to be
+ * constant (i.e. same value applies to all channels/bands) while the
+ * factory measurements are being made.
+ *
+ * 3) Up to 8 sets of factory-measured txpower calibration values.
+ * These are for different frequency ranges, since txpower gain
+ * characteristics of the analog radio circuitry vary with frequency.
+ *
+ * Not all sets need to be filled with data;
+ * struct iwl4965_eeprom_calib_subband_info contains range of channels
+ * (0 if unused) for each set of data.
+ */
+struct iwl4965_eeprom_calib_info {
+ u8 saturation_power24; /* half-dBm (e.g. "34" = 17 dBm) */
+ u8 saturation_power52; /* half-dBm */
+ s16 voltage; /* signed */
+ struct iwl4965_eeprom_calib_subband_info band_info[EEPROM_TX_POWER_BANDS];
+} __attribute__ ((packed));
+
+
+/*
+ * 4965 EEPROM map
+ */
+struct iwl4965_eeprom {
+ u8 reserved0[16];
+#define EEPROM_DEVICE_ID (2*0x08) /* 2 bytes */
+ u16 device_id; /* abs.ofs: 16 */
+ u8 reserved1[2];
+#define EEPROM_PMC (2*0x0A) /* 2 bytes */
+ u16 pmc; /* abs.ofs: 20 */
+ u8 reserved2[20];
+#define EEPROM_MAC_ADDRESS (2*0x15) /* 6 bytes */
+ u8 mac_address[6]; /* abs.ofs: 42 */
+ u8 reserved3[58];
+#define EEPROM_BOARD_REVISION (2*0x35) /* 2 bytes */
+ u16 board_revision; /* abs.ofs: 106 */
+ u8 reserved4[11];
+#define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */
+ u8 board_pba_number[9]; /* abs.ofs: 119 */
+ u8 reserved5[8];
+#define EEPROM_VERSION (2*0x44) /* 2 bytes */
+ u16 version; /* abs.ofs: 136 */
+#define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */
+ u8 sku_cap; /* abs.ofs: 138 */
+#define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */
+ u8 leds_mode; /* abs.ofs: 139 */
+#define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */
+ u16 oem_mode;
+#define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */
+ u16 wowlan_mode; /* abs.ofs: 142 */
+#define EEPROM_LEDS_TIME_INTERVAL (2*0x48) /* 2 bytes */
+ u16 leds_time_interval; /* abs.ofs: 144 */
+#define EEPROM_LEDS_OFF_TIME (2*0x49) /* 1 bytes */
+ u8 leds_off_time; /* abs.ofs: 146 */
+#define EEPROM_LEDS_ON_TIME (2*0x49+1) /* 1 bytes */
+ u8 leds_on_time; /* abs.ofs: 147 */
+#define EEPROM_ALMGOR_M_VERSION (2*0x4A) /* 1 bytes */
+ u8 almgor_m_version; /* abs.ofs: 148 */
+#define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */
+ u8 antenna_switch_type; /* abs.ofs: 149 */
+ u8 reserved6[8];
+#define EEPROM_4965_BOARD_REVISION (2*0x4F) /* 2 bytes */
+ u16 board_revision_4965; /* abs.ofs: 158 */
+ u8 reserved7[13];
+#define EEPROM_4965_BOARD_PBA (2*0x56+1) /* 9 bytes */
+ u8 board_pba_number_4965[9]; /* abs.ofs: 173 */
+ u8 reserved8[10];
+#define EEPROM_REGULATORY_SKU_ID (2*0x60) /* 4 bytes */
+ u8 sku_id[4]; /* abs.ofs: 192 */
+
+/*
+ * Per-channel regulatory data.
+ *
+ * Each channel that *might* be supported by 3945 or 4965 has a fixed location
+ * in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
+ * txpower (MSB).
+ *
+ * Entries immediately below are for 20 MHz channel width. FAT (40 MHz)
+ * channels (only for 4965, not supported by 3945) appear later in the EEPROM.
+ *
+ * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
+ */
+#define EEPROM_REGULATORY_BAND_1 (2*0x62) /* 2 bytes */
+ u16 band_1_count; /* abs.ofs: 196 */
+#define EEPROM_REGULATORY_BAND_1_CHANNELS (2*0x63) /* 28 bytes */
+ struct iwl4965_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */
+
+/*
+ * 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196,
+ * 5.0 GHz channels 7, 8, 11, 12, 16
+ * (4915-5080MHz) (none of these is ever supported)
+ */
+#define EEPROM_REGULATORY_BAND_2 (2*0x71) /* 2 bytes */
+ u16 band_2_count; /* abs.ofs: 226 */
+#define EEPROM_REGULATORY_BAND_2_CHANNELS (2*0x72) /* 26 bytes */
+ struct iwl4965_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */
+
+/*
+ * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
+ * (5170-5320MHz)
+ */
+#define EEPROM_REGULATORY_BAND_3 (2*0x7F) /* 2 bytes */
+ u16 band_3_count; /* abs.ofs: 254 */
+#define EEPROM_REGULATORY_BAND_3_CHANNELS (2*0x80) /* 24 bytes */
+ struct iwl4965_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */
+
+/*
+ * 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
+ * (5500-5700MHz)
+ */
+#define EEPROM_REGULATORY_BAND_4 (2*0x8C) /* 2 bytes */
+ u16 band_4_count; /* abs.ofs: 280 */
+#define EEPROM_REGULATORY_BAND_4_CHANNELS (2*0x8D) /* 22 bytes */
+ struct iwl4965_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */
+
+/*
+ * 5.7 GHz channels 145, 149, 153, 157, 161, 165
+ * (5725-5825MHz)
+ */
+#define EEPROM_REGULATORY_BAND_5 (2*0x98) /* 2 bytes */
+ u16 band_5_count; /* abs.ofs: 304 */
+#define EEPROM_REGULATORY_BAND_5_CHANNELS (2*0x99) /* 12 bytes */
+ struct iwl4965_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */
+
+ u8 reserved10[2];
+
+
+/*
+ * 2.4 GHz FAT channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11)
+ *
+ * The channel listed is the center of the lower 20 MHz half of the channel.
+ * The overall center frequency is actually 2 channels (10 MHz) above that,
+ * and the upper half of each FAT channel is centered 4 channels (20 MHz) away
+ * from the lower half; e.g. the upper half of FAT channel 1 is channel 5,
+ * and the overall FAT channel width centers on channel 3.
+ *
+ * NOTE: The RXON command uses 20 MHz channel numbers to specify the
+ * control channel to which to tune. RXON also specifies whether the
+ * control channel is the upper or lower half of a FAT channel.
+ *
+ * NOTE: 4965 does not support FAT channels on 2.4 GHz.
+ */
+#define EEPROM_REGULATORY_BAND_24_FAT_CHANNELS (2*0xA0) /* 14 bytes */
+ struct iwl4965_eeprom_channel band_24_channels[7]; /* abs.ofs: 320 */
+ u8 reserved11[2];
+
+/*
+ * 5.2 GHz FAT channels 36 (40), 44 (48), 52 (56), 60 (64),
+ * 100 (104), 108 (112), 116 (120), 124 (128), 132 (136), 149 (153), 157 (161)
+ */
+#define EEPROM_REGULATORY_BAND_52_FAT_CHANNELS (2*0xA8) /* 22 bytes */
+ struct iwl4965_eeprom_channel band_52_channels[11]; /* abs.ofs: 336 */
+ u8 reserved12[6];
+
+/*
+ * 4965 driver requires txpower calibration format version 5 or greater.
+ * Driver does not work with txpower calibration version < 5.
+ * This value is simply a 16-bit number, no major/minor versions here.
+ */
+#define EEPROM_CALIB_VERSION_OFFSET (2*0xB6) /* 2 bytes */
+ u16 calib_version; /* abs.ofs: 364 */
+ u8 reserved13[2];
+ u8 reserved14[96]; /* abs.ofs: 368 */
+
+/*
+ * 4965 Txpower calibration data.
+ */
+#define EEPROM_IWL_CALIB_TXPOWER_OFFSET (2*0xE8) /* 48 bytes */
+ struct iwl4965_eeprom_calib_info calib_info; /* abs.ofs: 464 */
+
+ u8 reserved16[140]; /* fill out to full 1024 byte block */
+
+
+} __attribute__ ((packed));
+
+#define IWL_EEPROM_IMAGE_SIZE 1024
+
+/* End of EEPROM */
+
+#include "iwl-4965-commands.h"
+
+#define PCI_LINK_CTRL 0x0F0
+#define PCI_POWER_SOURCE 0x0C8
+#define PCI_REG_WUM8 0x0E8
+#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000)
+
+/*=== CSR (control and status registers) ===*/
+#define CSR_BASE (0x000)
+
+#define CSR_SW_VER (CSR_BASE+0x000)
+#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
+#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
+#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
+#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
+#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
+#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
+#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
+#define CSR_GP_CNTRL (CSR_BASE+0x024)
+
+/*
+ * Hardware revision info
+ * Bit fields:
+ * 31-8: Reserved
+ * 7-4: Type of device: 0x0 = 4965, 0xd = 3945
+ * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
+ * 1-0: "Dash" value, as in A-1, etc.
+ *
+ * NOTE: Revision step affects calculation of CCK txpower for 4965.
+ */
+#define CSR_HW_REV (CSR_BASE+0x028)
+
+/* EEPROM reads */
+#define CSR_EEPROM_REG (CSR_BASE+0x02c)
+#define CSR_EEPROM_GP (CSR_BASE+0x030)
+#define CSR_GP_UCODE (CSR_BASE+0x044)
+#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
+#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
+#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
+#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
+#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
+
+/*
+ * Indicates hardware rev, to determine CCK backoff for txpower calculation.
+ * Bit fields:
+ * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step
+ */
+#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
+
+#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
+
+/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
+ * acknowledged (reset) by host writing "1" to flagged bits. */
+#define CSR_INT_BIT_FH_RX (1<<31) /* Rx DMA, cmd responses, FH_INT[17:16] */
+#define CSR_INT_BIT_HW_ERR (1<<29) /* DMA hardware error FH_INT[31] */
+#define CSR_INT_BIT_DNLD (1<<28) /* uCode Download */
+#define CSR_INT_BIT_FH_TX (1<<27) /* Tx DMA FH_INT[1:0] */
+#define CSR_INT_BIT_MAC_CLK_ACTV (1<<26) /* NIC controller's clock toggled on/off */
+#define CSR_INT_BIT_SW_ERR (1<<25) /* uCode error */
+#define CSR_INT_BIT_RF_KILL (1<<7) /* HW RFKILL switch GP_CNTRL[27] toggled */
+#define CSR_INT_BIT_CT_KILL (1<<6) /* Critical temp (chip too hot) rfkill */
+#define CSR_INT_BIT_SW_RX (1<<3) /* Rx, command responses, 3945 */
+#define CSR_INT_BIT_WAKEUP (1<<1) /* NIC controller waking up (pwr mgmt) */
+#define CSR_INT_BIT_ALIVE (1<<0) /* uCode interrupts once it initializes */
+
+#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
+ CSR_INT_BIT_HW_ERR | \
+ CSR_INT_BIT_FH_TX | \
+ CSR_INT_BIT_SW_ERR | \
+ CSR_INT_BIT_RF_KILL | \
+ CSR_INT_BIT_SW_RX | \
+ CSR_INT_BIT_WAKEUP | \
+ CSR_INT_BIT_ALIVE)
+
+/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
+#define CSR_FH_INT_BIT_ERR (1<<31) /* Error */
+#define CSR_FH_INT_BIT_HI_PRIOR (1<<30) /* High priority Rx, bypass coalescing */
+#define CSR_FH_INT_BIT_RX_CHNL1 (1<<17) /* Rx channel 1 */
+#define CSR_FH_INT_BIT_RX_CHNL0 (1<<16) /* Rx channel 0 */
+#define CSR_FH_INT_BIT_TX_CHNL1 (1<<1) /* Tx channel 1 */
+#define CSR_FH_INT_BIT_TX_CHNL0 (1<<0) /* Tx channel 0 */
+
+#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
+ CSR_FH_INT_BIT_RX_CHNL1 | \
+ CSR_FH_INT_BIT_RX_CHNL0)
+
+#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \
+ CSR_FH_INT_BIT_TX_CHNL0)
+
+
+/* RESET */
+#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
+#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
+#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
+#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
+#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
+
+/* GP (general purpose) CONTROL */
+#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
+#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
+#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
+#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
+
+#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
+
+#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
+#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
+#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
+
+
+/* EEPROM REG */
+#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
+#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
+
+/* EEPROM GP */
+#define CSR_EEPROM_GP_VALID_MSK (0x00000006)
+#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000)
+#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
+
+/* UCODE DRV GP */
+#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
+#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
+#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
+#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
+
+/* GPIO */
+#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
+#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
+#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER
+
+/* GI Chicken Bits */
+#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
+#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
+
+/*=== HBUS (Host-side Bus) ===*/
+#define HBUS_BASE (0x400)
+
+/*
+ * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM
+ * structures, error log, event log, verifying uCode load).
+ * First write to address register, then read from or write to data register
+ * to complete the job. Once the address register is set up, accesses to
+ * data registers auto-increment the address by one dword.
+ * Bit usage for address registers (read or write):
+ * 0-31: memory address within device
+ */
+#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c)
+#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010)
+#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018)
+#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c)
+
+/*
+ * Registers for accessing device's internal peripheral registers
+ * (e.g. SCD, BSM, etc.). First write to address register,
+ * then read from or write to data register to complete the job.
+ * Bit usage for address registers (read or write):
+ * 0-15: register address (offset) within device
+ * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword)
+ */
+#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044)
+#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048)
+#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c)
+#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050)
+
+/*
+ * Per-Tx-queue write pointer (index, really!) (3945 and 4965).
+ * Indicates index to next TFD that driver will fill (1 past latest filled).
+ * Bit usage:
+ * 0-7: queue write index (0-255)
+ * 11-8: queue selector (0-15)
+ */
+#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
+
+#define HBUS_TARG_MBX_C (HBUS_BASE+0x030)
+
+/*=== FH (data Flow Handler) ===*/
+#define FH_BASE (0x800)
+
+#define FH_RSCSR_CHNL0_WPTR (FH_RSCSR_CHNL0_RBDCB_WPTR_REG)
+
+/* RSSR */
+#define FH_RSSR_CTRL (FH_RSSR_TABLE+0x000)
+#define FH_RSSR_STATUS (FH_RSSR_TABLE+0x004)
+/* TCSR */
+#define FH_TCSR(_channel) (FH_TCSR_TABLE+(_channel)*0x20)
+#define FH_TCSR_CONFIG(_channel) (FH_TCSR(_channel)+0x00)
+#define FH_TCSR_CREDIT(_channel) (FH_TCSR(_channel)+0x04)
+#define FH_TCSR_BUFF_STTS(_channel) (FH_TCSR(_channel)+0x08)
+/* TSSR */
+#define FH_TSSR_CBB_BASE (FH_TSSR_TABLE+0x000)
+#define FH_TSSR_MSG_CONFIG (FH_TSSR_TABLE+0x008)
+#define FH_TSSR_TX_STATUS (FH_TSSR_TABLE+0x010)
+/* 18 - reserved */
+
+/* card static random access memory (SRAM) for processor data and instructs */
+#define RTC_INST_LOWER_BOUND (0x000000)
+#define RTC_DATA_LOWER_BOUND (0x800000)
+
+#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004)
+
+#define TFD_QUEUE_SIZE_MAX (256)
+
+/* spectrum and channel data structures */
+#define IWL_NUM_SCAN_RATES (2)
+
+#define IWL_DEFAULT_TX_RETRY 15
+
+#define RX_QUEUE_SIZE 256
+#define RX_QUEUE_MASK 255
+#define RX_QUEUE_SIZE_LOG 8
+
+#define TFD_TX_CMD_SLOTS 256
+#define TFD_CMD_SLOTS 32
+
+#define TFD_MAX_PAYLOAD_SIZE (sizeof(struct iwl4965_cmd) - \
+ sizeof(struct iwl4965_cmd_meta))
+
+/*
+ * RX related structures and functions
+ */
+#define RX_FREE_BUFFERS 64
+#define RX_LOW_WATERMARK 8
+
+
#define IWL_RX_BUF_SIZE (4 * 1024)
#define IWL_MAX_BSM_SIZE BSM_SRAM_SIZE
#define KDR_RTC_INST_UPPER_BOUND (0x018000)
#define IWL_MAX_INST_SIZE KDR_RTC_INST_SIZE
#define IWL_MAX_DATA_SIZE KDR_RTC_DATA_SIZE
-static inline int iwl_hw_valid_rtc_data_addr(u32 addr)
+static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr)
{
return (addr >= RTC_DATA_LOWER_BOUND) &&
(addr < KDR_RTC_DATA_UPPER_BOUND);
(((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \
((t) > IWL_TX_POWER_TEMPERATURE_MAX))
-#define IWL_TX_POWER_ILLEGAL_TEMPERATURE (300)
-
-#define IWL_TX_POWER_TEMPERATURE_DIFFERENCE (2)
-
#define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6)
#define IWL_TX_POWER_TARGET_POWER_MIN (0) /* 0 dBm = 1 milliwatt */
#define IWL_TX_POWER_TARGET_POWER_MAX (16) /* 16 dBm */
-/* timeout equivalent to 3 minutes */
-#define IWL_TX_POWER_TIMELIMIT_NOCALIB 1800000000
-
-#define IWL_TX_POWER_CCK_COMPENSATION (9)
-
#define MIN_TX_GAIN_INDEX (0)
#define MIN_TX_GAIN_INDEX_52GHZ_EXT (-9)
-#define MAX_TX_GAIN_INDEX_52GHZ (98)
-#define MIN_TX_GAIN_52GHZ (98)
-#define MAX_TX_GAIN_INDEX_24GHZ (98)
-#define MIN_TX_GAIN_24GHZ (98)
-#define MAX_TX_GAIN (0)
-#define MAX_TX_GAIN_52GHZ_EXT (-9)
#define IWL_TX_POWER_DEFAULT_REGULATORY_24 (34)
#define IWL_TX_POWER_DEFAULT_REGULATORY_52 (34)
#define IWL_TX_POWER_SATURATION_MIN (20)
#define IWL_TX_POWER_SATURATION_MAX (50)
-/* dv *0.4 = dt; so that 5 degrees temperature diff equals
- * 12.5 in voltage diff */
-#define IWL_TX_TEMPERATURE_UPDATE_LIMIT 9
-
-#define IWL_INVALID_CHANNEL (0xffffffff)
-#define IWL_TX_POWER_REGITRY_BIT (2)
-
-#define MIN_IWL_TX_POWER_CALIB_DUR (100)
-#define IWL_CCK_FROM_OFDM_POWER_DIFF (-5)
-#define IWL_CCK_FROM_OFDM_INDEX_DIFF (9)
-
-/* Number of entries in the gain table */
-#define POWER_GAIN_NUM_ENTRIES 78
-#define TX_POW_MAX_SESSION_NUM 5
-/* timeout equivalent to 3 minutes */
-#define TX_IWL_TIMELIMIT_NOCALIB 1800000000
-
-/* Kedron TX_CALIB_STATES */
-#define IWL_TX_CALIB_STATE_SEND_TX 0x00000001
-#define IWL_TX_CALIB_WAIT_TX_RESPONSE 0x00000002
-#define IWL_TX_CALIB_ENABLED 0x00000004
-#define IWL_TX_CALIB_XVT_ON 0x00000008
-#define IWL_TX_CALIB_TEMPERATURE_CORRECT 0x00000010
-#define IWL_TX_CALIB_WORKING_WITH_XVT 0x00000020
-#define IWL_TX_CALIB_XVT_PERIODICAL 0x00000040
-
-#define NUM_IWL_TX_CALIB_SETTINS 5 /* Number of tx correction groups */
-
-#define IWL_MIN_POWER_IN_VP_TABLE 1 /* 0.5dBm multiplied by 2 */
-#define IWL_MAX_POWER_IN_VP_TABLE 40 /* 20dBm - multiplied by 2 (because
- * entries are for each 0.5dBm) */
-#define IWL_STEP_IN_VP_TABLE 1 /* 0.5dB - multiplied by 2 */
-#define IWL_NUM_POINTS_IN_VPTABLE \
- (1 + IWL_MAX_POWER_IN_VP_TABLE - IWL_MIN_POWER_IN_VP_TABLE)
-
-#define MIN_TX_GAIN_INDEX (0)
-#define MAX_TX_GAIN_INDEX_52GHZ (98)
-#define MIN_TX_GAIN_52GHZ (98)
-#define MAX_TX_GAIN_INDEX_24GHZ (98)
-#define MIN_TX_GAIN_24GHZ (98)
-#define MAX_TX_GAIN (0)
-
/* First and last channels of all groups */
#define CALIB_IWL_TX_ATTEN_GR1_FCH 34
#define CALIB_IWL_TX_ATTEN_GR1_LCH 43
#define CALIB_IWL_TX_ATTEN_GR5_FCH 1
#define CALIB_IWL_TX_ATTEN_GR5_LCH 20
-
-union iwl_tx_power_dual_stream {
- struct {
- u8 radio_tx_gain[2];
- u8 dsp_predis_atten[2];
- } s;
- u32 dw;
-};
-
/********************* END TXPOWER *****************************************/
-/* HT flags */
-#define RXON_FLG_CTRL_CHANNEL_LOC_POS (22)
-#define RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK __constant_cpu_to_le32(0x1<<22)
-
-#define RXON_FLG_HT_OPERATING_MODE_POS (23)
-
-#define RXON_FLG_HT_PROT_MSK __constant_cpu_to_le32(0x1<<23)
-#define RXON_FLG_FAT_PROT_MSK __constant_cpu_to_le32(0x2<<23)
-
-#define RXON_FLG_CHANNEL_MODE_POS (25)
-#define RXON_FLG_CHANNEL_MODE_MSK __constant_cpu_to_le32(0x3<<25)
-#define RXON_FLG_CHANNEL_MODE_PURE_40_MSK __constant_cpu_to_le32(0x1<<25)
-#define RXON_FLG_CHANNEL_MODE_MIXED_MSK __constant_cpu_to_le32(0x2<<25)
-
-#define RXON_RX_CHAIN_DRIVER_FORCE_MSK __constant_cpu_to_le16(0x1<<0)
-#define RXON_RX_CHAIN_VALID_MSK __constant_cpu_to_le16(0x7<<1)
-#define RXON_RX_CHAIN_VALID_POS (1)
-#define RXON_RX_CHAIN_FORCE_SEL_MSK __constant_cpu_to_le16(0x7<<4)
-#define RXON_RX_CHAIN_FORCE_SEL_POS (4)
-#define RXON_RX_CHAIN_FORCE_MIMO_SEL_MSK __constant_cpu_to_le16(0x7<<7)
-#define RXON_RX_CHAIN_FORCE_MIMO_SEL_POS (7)
-#define RXON_RX_CHAIN_CNT_MSK __constant_cpu_to_le16(0x3<<10)
-#define RXON_RX_CHAIN_CNT_POS (10)
-#define RXON_RX_CHAIN_MIMO_CNT_MSK __constant_cpu_to_le16(0x3<<12)
-#define RXON_RX_CHAIN_MIMO_CNT_POS (12)
-#define RXON_RX_CHAIN_MIMO_FORCE_MSK __constant_cpu_to_le16(0x1<<14)
-#define RXON_RX_CHAIN_MIMO_FORCE_POS (14)
-
-
-#define MCS_DUP_6M_PLCP 0x20
-
-/* OFDM HT rate masks */
-/* ***************************************** */
-#define R_MCS_6M_MSK 0x1
-#define R_MCS_12M_MSK 0x2
-#define R_MCS_18M_MSK 0x4
-#define R_MCS_24M_MSK 0x8
-#define R_MCS_36M_MSK 0x10
-#define R_MCS_48M_MSK 0x20
-#define R_MCS_54M_MSK 0x40
-#define R_MCS_60M_MSK 0x80
-#define R_MCS_12M_DUAL_MSK 0x100
-#define R_MCS_24M_DUAL_MSK 0x200
-#define R_MCS_36M_DUAL_MSK 0x400
-#define R_MCS_48M_DUAL_MSK 0x800
-
-#define is_legacy(tbl) (((tbl) == LQ_G) || ((tbl) == LQ_A))
-#define is_siso(tbl) (((tbl) == LQ_SISO))
-#define is_mimo(tbl) (((tbl) == LQ_MIMO))
-#define is_Ht(tbl) (is_siso(tbl) || is_mimo(tbl))
-#define is_a_band(tbl) (((tbl) == LQ_A))
-#define is_g_and(tbl) (((tbl) == LQ_G))
-
/* Flow Handler Definitions */
/**********************/
#define IWL_FH_TCSR_LOWER_BOUND (IWL_FH_REGS_LOWER_BOUND + 0xD00)
#define IWL_FH_TCSR_UPPER_BOUND (IWL_FH_REGS_LOWER_BOUND + 0xE60)
-#define IWL_FH_TCSR_CHNL_NUM (7)
#define IWL_FH_TCSR_CHNL_TX_CONFIG_REG(_chnl) \
(IWL_FH_TCSR_LOWER_BOUND + 0x20 * _chnl)
#define IWL_FH_TSSR_LOWER_BOUND (IWL_FH_REGS_LOWER_BOUND + 0xEA0)
#define IWL_FH_TSSR_UPPER_BOUND (IWL_FH_REGS_LOWER_BOUND + 0xEC0)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG (IWL_FH_TSSR_LOWER_BOUND + 0x008)
#define IWL_FH_TSSR_TX_STATUS_REG (IWL_FH_TSSR_LOWER_BOUND + 0x010)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TXPD_ON (0xFF000000)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_TXPD_ON (0x00FF0000)
-
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_64B (0x00000000)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_128B (0x00000400)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_256B (0x00000800)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_512B (0x00000C00)
-
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TFD_ON (0x00000100)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_CBB_ON (0x00000080)
-
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RSP_WAIT_TH (0x00000020)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_RSP_WAIT_TH (0x00000005)
-
#define IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl) \
((1 << (_chnl)) << 24)
#define IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl) \
(IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl) | \
IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl))
-/* TCSR: tx_config register values */
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_TXF (0x00000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_DRIVER (0x00000001)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_ARC (0x00000002)
-
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE_VAL (0x00000000)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL (0x00000008)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_NOINT (0x00000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_ENDTFD (0x00100000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_IFTFD (0x00200000)
-
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_NOINT (0x00000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_ENDTFD (0x00400000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_IFTFD (0x00800000)
-
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE (0x00000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE_EOF (0x40000000)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000)
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_EMPTY (0x00000000)
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_WAIT (0x00002000)
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_VALID (0x00000003)
-
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_BIT_TFDB_WPTR (0x00000001)
-
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_NUM (20)
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_IDX (12)
-
/* RCSR: channel 0 rx_config register defines */
-#define FH_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MASK (0xC0000000) /* bits 30-31 */
-#define FH_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MASK (0x00F00000) /* bits 20-23 */
-#define FH_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MASK (0x00030000) /* bits 16-17 */
-#define FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MASK (0x00008000) /* bit 15 */
-#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MASK (0x00001000) /* bit 12 */
-#define FH_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MASK (0x00000FF0) /* bit 4-11 */
#define FH_RCSR_RX_CONFIG_RBDCB_SIZE_BITSHIFT (20)
-#define FH_RCSR_RX_CONFIG_RB_SIZE_BITSHIFT (16)
-/* RCSR: rx_config register values */
-#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000)
-#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000)
#define FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000)
#define IWL_FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000)
/* RCSR channel 0 config register values */
-#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000)
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000)
-/* RSCSR: defs used in normal mode */
-#define FH_RSCSR_CHNL0_RBDCB_WPTR_MASK (0x00000FFF) /* bits 0-11 */
-
#define SCD_WIN_SIZE 64
#define SCD_FRAME_LIMIT 64
-/* memory mapped registers */
-#define SCD_START_OFFSET 0xa02c00
-
-#define SCD_SRAM_BASE_ADDR (SCD_START_OFFSET + 0x0)
-#define SCD_EMPTY_BITS (SCD_START_OFFSET + 0x4)
-#define SCD_DRAM_BASE_ADDR (SCD_START_OFFSET + 0x10)
-#define SCD_AIT (SCD_START_OFFSET + 0x18)
-#define SCD_TXFACT (SCD_START_OFFSET + 0x1c)
-#define SCD_QUEUE_WRPTR(x) (SCD_START_OFFSET + 0x24 + (x) * 4)
-#define SCD_QUEUE_RDPTR(x) (SCD_START_OFFSET + 0x64 + (x) * 4)
-#define SCD_SETQUEUENUM (SCD_START_OFFSET + 0xa4)
-#define SCD_SET_TXSTAT_TXED (SCD_START_OFFSET + 0xa8)
-#define SCD_SET_TXSTAT_DONE (SCD_START_OFFSET + 0xac)
-#define SCD_SET_TXSTAT_NOT_SCHD (SCD_START_OFFSET + 0xb0)
-#define SCD_DECREASE_CREDIT (SCD_START_OFFSET + 0xb4)
-#define SCD_DECREASE_SCREDIT (SCD_START_OFFSET + 0xb8)
-#define SCD_LOAD_CREDIT (SCD_START_OFFSET + 0xbc)
-#define SCD_LOAD_SCREDIT (SCD_START_OFFSET + 0xc0)
-#define SCD_BAR (SCD_START_OFFSET + 0xc4)
-#define SCD_BAR_DW0 (SCD_START_OFFSET + 0xc8)
-#define SCD_BAR_DW1 (SCD_START_OFFSET + 0xcc)
-#define SCD_QUEUECHAIN_SEL (SCD_START_OFFSET + 0xd0)
-#define SCD_QUERY_REQ (SCD_START_OFFSET + 0xd8)
-#define SCD_QUERY_RES (SCD_START_OFFSET + 0xdc)
-#define SCD_PENDING_FRAMES (SCD_START_OFFSET + 0xe0)
-#define SCD_INTERRUPT_MASK (SCD_START_OFFSET + 0xe4)
-#define SCD_INTERRUPT_THRESHOLD (SCD_START_OFFSET + 0xe8)
-#define SCD_QUERY_MIN_FRAME_SIZE (SCD_START_OFFSET + 0x100)
-#define SCD_QUEUE_STATUS_BITS(x) (SCD_START_OFFSET + 0x104 + (x) * 4)
-
/* SRAM structures */
#define SCD_CONTEXT_DATA_OFFSET 0x380
#define SCD_TX_STTS_BITMAP_OFFSET 0x400
#define SCD_TXFACT_REG_TXFIFO_MASK(lo, hi) \
((1<<(hi))|((1<<(hi))-(1<<(lo))))
-
-#define SCD_MODE_REG_BIT_SEARCH_MODE (1<<0)
-#define SCD_MODE_REG_BIT_SBYP_MODE (1<<1)
-
-#define SCD_TXFIFO_POS_TID (0)
-#define SCD_TXFIFO_POS_RA (4)
#define SCD_QUEUE_STTS_REG_POS_ACTIVE (0)
#define SCD_QUEUE_STTS_REG_POS_TXF (1)
#define SCD_QUEUE_STTS_REG_POS_WSL (5)
#define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (10)
#define SCD_QUEUE_STTS_REG_MSK (0x0007FC00)
-#define SCD_QUEUE_RA_TID_MAP_RATID_MSK (0x01FF)
-
#define SCD_QUEUE_CTX_REG1_WIN_SIZE_POS (0)
#define SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK (0x0000007F)
-#define SCD_QUEUE_CTX_REG1_CREDIT_POS (8)
-#define SCD_QUEUE_CTX_REG1_CREDIT_MSK (0x00FFFF00)
-#define SCD_QUEUE_CTX_REG1_SUPER_CREDIT_POS (24)
-#define SCD_QUEUE_CTX_REG1_SUPER_CREDIT_MSK (0xFF000000)
+
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS (16)
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK (0x007F0000)
#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100)
#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200)
-static inline u8 iwl_hw_get_rate(__le32 rate_n_flags)
+static inline u8 iwl4965_hw_get_rate(__le32 rate_n_flags)
{
return le32_to_cpu(rate_n_flags) & 0xFF;
}
-static inline u16 iwl_hw_get_rate_n_flags(__le32 rate_n_flags)
+static inline u16 iwl4965_hw_get_rate_n_flags(__le32 rate_n_flags)
{
return le32_to_cpu(rate_n_flags) & 0xFFFF;
}
-static inline __le32 iwl_hw_set_rate_n_flags(u8 rate, u16 flags)
+static inline __le32 iwl4965_hw_set_rate_n_flags(u8 rate, u16 flags)
{
return cpu_to_le32(flags|(u16)rate);
}
-struct iwl_tfd_frame_data {
+struct iwl4965_tfd_frame_data {
__le32 tb1_addr;
__le32 val1;
#define IWL_tb2_len_SYM val2
} __attribute__ ((packed));
-struct iwl_tfd_frame {
+struct iwl4965_tfd_frame {
__le32 val0;
/* __le32 rsvd1:24; */
/* __le32 num_tbs:5; */
#define IWL_num_tbs_SYM val0
/* __le32 rsvd2:1; */
/* __le32 padding:2; */
- struct iwl_tfd_frame_data pa[10];
+ struct iwl4965_tfd_frame_data pa[10];
__le32 reserved;
} __attribute__ ((packed));
sizeof(__le16)];
} __attribute__ ((packed));
-/* Base physical address of iwl_shared is provided to SCD_DRAM_BASE_ADDR
- * and &iwl_shared.val0 is provided to FH_RSCSR_CHNL0_STTS_WPTR_REG */
-struct iwl_shared {
+/* Base physical address of iwl4965_shared is provided to KDR_SCD_DRAM_BASE_ADDR
+ * and &iwl4965_shared.val0 is provided to FH_RSCSR_CHNL0_STTS_WPTR_REG */
+struct iwl4965_shared {
struct iwl4965_sched_queue_byte_cnt_tbl
queues_byte_cnt_tbls[IWL_MAX_NUM_QUEUES];
__le32 val0;
__le32 padding2;
} __attribute__ ((packed));
-#endif /* __iwl_4965_hw_h__ */
+#endif /* __iwl4965_4965_hw_h__ */
projects / linux-2.6 / blobdiff