* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*****************************************************************************/
+/*
+ * Please use this file (iwl-3945-hw.h) only for hardware-related definitions.
+ * Please use iwl-3945-commands.h for uCode API definitions.
+ * Please use iwl-3945.h for driver implementation definitions.
+ */
#ifndef __iwl_3945_hw__
#define __iwl_3945_hw__
/* Tx rates */
#define IWL_CCK_RATES 4
#define IWL_OFDM_RATES 8
-
#define IWL_HT_RATES 0
-
#define IWL_MAX_RATES (IWL_CCK_RATES+IWL_OFDM_RATES+IWL_HT_RATES)
/* Time constants */
#define PCI_REG_WUM8 0x0E8
#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000)
-/*=== CSR (control and status registers) ===*/
-#define CSR_BASE (0x000)
-
-#define CSR_SW_VER (CSR_BASE+0x000)
-#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
-#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
-#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
-#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
-#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
-#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
-#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
-#define CSR_GP_CNTRL (CSR_BASE+0x024)
-
-/*
- * Hardware revision info
- * Bit fields:
- * 31-8: Reserved
- * 7-4: Type of device: 0x0 = 4965, 0xd = 3945
- * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
- * 1-0: "Dash" value, as in A-1, etc.
- */
-#define CSR_HW_REV (CSR_BASE+0x028)
-
-/* EEPROM reads */
-#define CSR_EEPROM_REG (CSR_BASE+0x02c)
-#define CSR_EEPROM_GP (CSR_BASE+0x030)
-#define CSR_GP_UCODE (CSR_BASE+0x044)
-#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
-#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
-#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
-#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
-#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
-
-/* Analog phase-lock-loop configuration (3945 only)
- * Set bit 24. */
-#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c)
-
-/* Bits for CSR_HW_IF_CONFIG_REG */
-#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MB (0x00000100)
-#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MM (0x00000200)
-#define CSR_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400)
-#define CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE (0x00000800)
-#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000)
-#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000)
-#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
-
-/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
- * acknowledged (reset) by host writing "1" to flagged bits. */
-#define CSR_INT_BIT_FH_RX (1<<31) /* Rx DMA, cmd responses, FH_INT[17:16] */
-#define CSR_INT_BIT_HW_ERR (1<<29) /* DMA hardware error FH_INT[31] */
-#define CSR_INT_BIT_DNLD (1<<28) /* uCode Download */
-#define CSR_INT_BIT_FH_TX (1<<27) /* Tx DMA FH_INT[1:0] */
-#define CSR_INT_BIT_MAC_CLK_ACTV (1<<26) /* NIC controller's clock toggled on/off */
-#define CSR_INT_BIT_SW_ERR (1<<25) /* uCode error */
-#define CSR_INT_BIT_RF_KILL (1<<7) /* HW RFKILL switch GP_CNTRL[27] toggled */
-#define CSR_INT_BIT_CT_KILL (1<<6) /* Critical temp (chip too hot) rfkill */
-#define CSR_INT_BIT_SW_RX (1<<3) /* Rx, command responses, 3945 */
-#define CSR_INT_BIT_WAKEUP (1<<1) /* NIC controller waking up (pwr mgmt) */
-#define CSR_INT_BIT_ALIVE (1<<0) /* uCode interrupts once it initializes */
-
-#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
- CSR_INT_BIT_HW_ERR | \
- CSR_INT_BIT_FH_TX | \
- CSR_INT_BIT_SW_ERR | \
- CSR_INT_BIT_RF_KILL | \
- CSR_INT_BIT_SW_RX | \
- CSR_INT_BIT_WAKEUP | \
- CSR_INT_BIT_ALIVE)
-
-/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
-#define CSR_FH_INT_BIT_ERR (1<<31) /* Error */
-#define CSR_FH_INT_BIT_HI_PRIOR (1<<30) /* High priority Rx, bypass coalescing */
-#define CSR_FH_INT_BIT_RX_CHNL2 (1<<18) /* Rx channel 2 (3945 only) */
-#define CSR_FH_INT_BIT_RX_CHNL1 (1<<17) /* Rx channel 1 */
-#define CSR_FH_INT_BIT_RX_CHNL0 (1<<16) /* Rx channel 0 */
-#define CSR_FH_INT_BIT_TX_CHNL6 (1<<6) /* Tx channel 6 (3945 only) */
-#define CSR_FH_INT_BIT_TX_CHNL1 (1<<1) /* Tx channel 1 */
-#define CSR_FH_INT_BIT_TX_CHNL0 (1<<0) /* Tx channel 0 */
-
-#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
- CSR_FH_INT_BIT_RX_CHNL2 | \
- CSR_FH_INT_BIT_RX_CHNL1 | \
- CSR_FH_INT_BIT_RX_CHNL0)
-
-#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL6 | \
- CSR_FH_INT_BIT_TX_CHNL1 | \
- CSR_FH_INT_BIT_TX_CHNL0)
-
-
-/* RESET */
-#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
-#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
-#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
-#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
-#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
-
-/* GP (general purpose) CONTROL */
-#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
-#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
-#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
-
-#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
-
-#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
-#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
-
-
-/* EEPROM REG */
-#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
-#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
-
-/* EEPROM GP */
-#define CSR_EEPROM_GP_VALID_MSK (0x00000006)
-#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000)
-#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
-
-/* UCODE DRV GP */
-#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
-#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
-#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
-#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
-
-/* GPIO */
-#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
-#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
-#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER
-
-/* GI Chicken Bits */
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
-
-/* CSR_ANA_PLL_CFG */
-#define CSR_ANA_PLL_CFG_SH (0x00880300)
-
-/*=== HBUS (Host-side Bus) ===*/
-#define HBUS_BASE (0x400)
-
-/*
- * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM
- * structures, error log, event log, verifying uCode load).
- * First write to address register, then read from or write to data register
- * to complete the job. Once the address register is set up, accesses to
- * data registers auto-increment the address by one dword.
- * Bit usage for address registers (read or write):
- * 0-31: memory address within device
- */
-#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c)
-#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010)
-#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018)
-#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c)
-
-/*
- * Registers for accessing device's internal peripheral registers
- * (e.g. SCD, BSM, etc.). First write to address register,
- * then read from or write to data register to complete the job.
- * Bit usage for address registers (read or write):
- * 0-15: register address (offset) within device
- * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword)
- */
-#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044)
-#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048)
-#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c)
-#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050)
-
-/*
- * Per-Tx-queue write pointer (index, really!) (3945 and 4965).
- * Indicates index to next TFD that driver will fill (1 past latest filled).
- * Bit usage:
- * 0-7: queue write index
- * 11-8: queue selector
- */
-#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
-
/* SCD (3945 Tx Frame Scheduler) */
#define SCD_BASE (CSR_BASE + 0x2E00)
#define FH_TSSR_CBB_BASE (FH_TSSR_TABLE+0x000)
#define FH_TSSR_MSG_CONFIG (FH_TSSR_TABLE+0x008)
#define FH_TSSR_TX_STATUS (FH_TSSR_TABLE+0x010)
-/* 18 - reserved */
-
-/* card static random access memory (SRAM) for processor data and instructs */
-#define RTC_INST_LOWER_BOUND (0x000000)
-#define RTC_DATA_LOWER_BOUND (0x800000)
/* DBM */
#define PCI_CFG_REV_ID_BIT_BASIC_SKU (0x40) /* bit 6 */
#define PCI_CFG_REV_ID_BIT_RTP (0x80) /* bit 7 */
-#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004)
-
#define TFD_QUEUE_MIN 0
#define TFD_QUEUE_MAX 6
#define TFD_QUEUE_SIZE_MAX (256)
-/* spectrum and channel data structures */
#define IWL_NUM_SCAN_RATES (2)
#define IWL_DEFAULT_TX_RETRY 15
#define U32_PAD(n) ((4-(n))&0x3)
-/*
- * Generic queue structure
- *
- * Contains common data for Rx and Tx queues
- */
-#define TFD_CTL_COUNT_SET(n) (n<<24)
-#define TFD_CTL_COUNT_GET(ctl) ((ctl>>24) & 7)
-#define TFD_CTL_PAD_SET(n) (n<<28)
-#define TFD_CTL_PAD_GET(ctl) (ctl>>28)
+#define TFD_CTL_COUNT_SET(n) (n << 24)
+#define TFD_CTL_COUNT_GET(ctl) ((ctl >> 24) & 7)
+#define TFD_CTL_PAD_SET(n) (n << 28)
+#define TFD_CTL_PAD_GET(ctl) (ctl >> 28)
#define TFD_TX_CMD_SLOTS 256
#define TFD_CMD_SLOTS 32
#define RX_FREE_BUFFERS 64
#define RX_LOW_WATERMARK 8
-
-#define IWL_RX_BUF_SIZE 3000
-/* card static random access memory (SRAM) for processor data and instructs */
+/* Sizes and addresses for instruction and data memory (SRAM) in
+ * 3945's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */
+#define RTC_INST_LOWER_BOUND (0x000000)
#define ALM_RTC_INST_UPPER_BOUND (0x014000)
+
+#define RTC_DATA_LOWER_BOUND (0x800000)
#define ALM_RTC_DATA_UPPER_BOUND (0x808000)
#define ALM_RTC_INST_SIZE (ALM_RTC_INST_UPPER_BOUND - RTC_INST_LOWER_BOUND)
#define ALM_RTC_DATA_SIZE (ALM_RTC_DATA_UPPER_BOUND - RTC_DATA_LOWER_BOUND)
-#define IWL_MAX_BSM_SIZE ALM_RTC_INST_SIZE
#define IWL_MAX_INST_SIZE ALM_RTC_INST_SIZE
#define IWL_MAX_DATA_SIZE ALM_RTC_DATA_SIZE
+
+/* Size of uCode instruction memory in bootstrap state machine */
+#define IWL_MAX_BSM_SIZE ALM_RTC_INST_SIZE
+
#define IWL_MAX_NUM_QUEUES 8
static inline int iwl3945_hw_valid_rtc_data_addr(u32 addr)
projects / linux-2.6 / blobdiff