configure your card:
<http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
+
+ It is recommended that you compile this driver as a module (M)
+ rather than built-in (Y). This driver requires firmware at device
+ initialization time, and when built-in this typically happens
+ before the filesystem is accessible (hence firmware will be
+ unavailable and initialization will fail). If you do choose to build
+ this driver into your kernel image, you can avoid this problem by
+ including the firmware and a firmware loader in an initramfs.
- If you want to compile the driver as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want),
- say M here and read <file:Documentation/kbuild/modules.txt>.
- The module will be called ipw2100.ko.
-
config IPW2100_MONITOR
bool "Enable promiscuous mode"
depends on IPW2100
configure your card:
<http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
-
- If you want to compile the driver as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want),
- say M here and read <file:Documentation/kbuild/modules.txt>.
- The module will be called ipw2200.ko.
+
+ It is recommended that you compile this driver as a module (M)
+ rather than built-in (Y). This driver requires firmware at device
+ initialization time, and when built-in this typically happens
+ before the filesystem is accessible (hence firmware will be
+ unavailable and initialization will fail). If you do choose to build
+ this driver into your kernel image, you can avoid this problem by
+ including the firmware and a firmware loader in an initramfs.
config IPW2200_MONITOR
bool "Enable promiscuous mode"
tristate "Marvell 8xxx Libertas WLAN driver support"
depends on WLAN_80211
select WIRELESS_EXT
- select IEEE80211
select FW_LOADER
---help---
A library for Marvell Libertas 8xxx devices.
config LIBERTAS_CS
tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
- depends on LIBERTAS && PCMCIA && EXPERIMENTAL
+ depends on LIBERTAS && PCMCIA
select FW_LOADER
---help---
A driver for Marvell Libertas 8385 CompactFlash devices.
To compile this driver as a module, choose M here: the
module will be called zd1201.
+config USB_NET_RNDIS_WLAN
+ tristate "Wireless RNDIS USB support"
+ depends on USB && WLAN_80211 && EXPERIMENTAL
+ select USB_USBNET
+ select USB_NET_CDCETHER
+ select USB_NET_RNDIS_HOST
+ select WIRELESS_EXT
+ ---help---
+ This is a driver for wireless RNDIS devices.
+ These are USB based adapters found in devices such as:
+
+ Buffalo WLI-U2-KG125S
+ U.S. Robotics USR5421
+ Belkin F5D7051
+ Linksys WUSB54GSv2
+ Linksys WUSB54GSC
+ Asus WL169gE
+ Eminent EM4045
+ BT Voyager 1055
+ Linksys WUSB54GSv1
+ U.S. Robotics USR5420
+ BUFFALO WLI-USB-G54
+
+ All of these devices are based on Broadcom 4320 chip which is the
+ only wireless RNDIS chip known to date.
+
+ If you choose to build a module, it'll be called rndis_wlan.
+
config RTL8180
tristate "Realtek 8180/8185 PCI support"
depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
If you choose to build a module, it'll be called p54pci.
-config ATH5K
- tristate "Atheros 5xxx wireless cards support"
- depends on PCI && MAC80211 && WLAN_80211 && EXPERIMENTAL
- ---help---
- This module adds support for wireless adapters based on
- Atheros 5xxx chipset.
-
- Currently the following chip versions are supported:
-
- MAC: AR5211 AR5212
- PHY: RF5111/2111 RF5112/2112 RF5413/2413
-
- This driver uses the kernel's mac80211 subsystem.
-
- If you choose to build a module, it'll be called ath5k. Say M if
- unsure.
-
+source "drivers/net/wireless/ath5k/Kconfig"
source "drivers/net/wireless/iwlwifi/Kconfig"
source "drivers/net/wireless/hostap/Kconfig"
-source "drivers/net/wireless/bcm43xx/Kconfig"
source "drivers/net/wireless/b43/Kconfig"
source "drivers/net/wireless/b43legacy/Kconfig"
source "drivers/net/wireless/zd1211rw/Kconfig"