PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */
PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */
PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */
+ PCI_Y2_PME_LEGACY= 1<<15, /* PCI Express legacy power management mode */
};
enum pci_dev_reg_2 {
/* B2_CHIP_ID 8 bit Chip Identification Number */
enum {
- CHIP_ID_GENESIS = 0x0a, /* Chip ID for GENESIS */
- CHIP_ID_YUKON = 0xb0, /* Chip ID for YUKON */
- CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
- CHIP_ID_YUKON_LP = 0xb2, /* Chip ID for YUKON-LP */
CHIP_ID_YUKON_XL = 0xb3, /* Chip ID for YUKON-2 XL */
CHIP_ID_YUKON_EC_U = 0xb4, /* Chip ID for YUKON-2 EC Ultra */
+ CHIP_ID_YUKON_EX = 0xb5, /* Chip ID for YUKON-2 Extreme */
CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */
CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */
PHY_ADDR_MARV = 0,
};
-#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
+#define RB_ADDR(offs, queue) ((u16) B16_RAM_REGS + (queue) + (offs))
enum {
BMU_FIFO_ENA | BMU_OP_ON,
BMU_WM_DEFAULT = 0x600,
+ BMU_WM_PEX = 0x80,
};
/* Tx BMU Control / Status Registers (Yukon-2) */
POLL_LIST_ADDR_HI= 0x0e2c,/* 32 bit Poll. List Start Addr (high) */
};
+enum {
+ SMB_CFG = 0x0e40, /* 32 bit SMBus Config Register */
+ SMB_CSR = 0x0e44, /* 32 bit SMBus Control/Status Register */
+};
+
+enum {
+ CPU_WDOG = 0x0e48, /* 32 bit Watchdog Register */
+ CPU_CNTR = 0x0e4C, /* 32 bit Counter Register */
+ CPU_TIM = 0x0e50,/* 32 bit Timer Compare Register */
+ CPU_AHB_ADDR = 0x0e54, /* 32 bit CPU AHB Debug Register */
+ CPU_AHB_WDATA = 0x0e58, /* 32 bit CPU AHB Debug Register */
+ CPU_AHB_RDATA = 0x0e5C, /* 32 bit CPU AHB Debug Register */
+ HCU_MAP_BASE = 0x0e60, /* 32 bit Reset Mapping Base */
+ CPU_AHB_CTRL = 0x0e64, /* 32 bit CPU AHB Debug Register */
+ HCU_CCSR = 0x0e68, /* 32 bit CPU Control and Status Register */
+ HCU_HCSR = 0x0e6C, /* 32 bit Host Control and Status Register */
+};
+
/* ASF Subsystem Registers (Yukon-2 only) */
enum {
B28_Y2_SMB_CONFIG = 0x0e40,/* 32 bit ASF SMBus Config Register */
GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */
/* Wake-up Frame Pattern Match Control Registers (YUKON only) */
-
- WOL_REG_OFFS = 0x20,/* HW-Bug: Address is + 0x20 against spec. */
-
WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */
WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */
WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */
WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */
- WOL_PATT_PME = 0x0f2a,/* 8 bit WOL PME Match Enable (Yukon-2) */
- WOL_PATT_ASFM = 0x0f2b,/* 8 bit WOL ASF Match Enable (Yukon-2) */
WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */
/* WOL Pattern Length Registers (YUKON only) */
-
WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */
WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */
/* WOL Pattern Counter Registers (YUKON only) */
-
-
WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */
WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */
};
+#define WOL_REGS(port, x) (x + (port)*0x80)
enum {
WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */
WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */
};
+#define WOL_PATT_RAM_BASE(port) (WOL_PATT_RAM_1 + (port)*0x400)
enum {
BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */
PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */
};
-#define PHY_M_PC_MDI_XMODE(x) (((x)<<5) & PHY_M_PC_MDIX_MSK)
+#define PHY_M_PC_MDI_XMODE(x) (((u16)(x)<<5) & PHY_M_PC_MDIX_MSK)
enum {
PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */
PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */
PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */};
-#define PHY_M_EC_M_DSC(x) ((x)<<10 & PHY_M_EC_M_DSC_MSK)
+#define PHY_M_EC_M_DSC(x) ((u16)(x)<<10 & PHY_M_EC_M_DSC_MSK)
/* 00=1x; 01=2x; 10=3x; 11=4x */
-#define PHY_M_EC_S_DSC(x) ((x)<<8 & PHY_M_EC_S_DSC_MSK)
+#define PHY_M_EC_S_DSC(x) ((u16)(x)<<8 & PHY_M_EC_S_DSC_MSK)
/* 00=dis; 01=1x; 10=2x; 11=3x */
-#define PHY_M_EC_DSC_2(x) ((x)<<9 & PHY_M_EC_M_DSC_MSK2)
+#define PHY_M_EC_DSC_2(x) ((u16)(x)<<9 & PHY_M_EC_M_DSC_MSK2)
/* 000=1x; 001=2x; 010=3x; 011=4x */
-#define PHY_M_EC_MAC_S(x) ((x)<<4 & PHY_M_EC_MAC_S_MSK)
+#define PHY_M_EC_MAC_S(x) ((u16)(x)<<4 & PHY_M_EC_MAC_S_MSK)
/* 01X=0; 110=2.5; 111=25 (MHz) */
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
};
/* !!! Errata in spec. (1 = disable) */
-#define PHY_M_PC_DSC(x) (((x)<<12) & PHY_M_PC_DSC_MSK)
+#define PHY_M_PC_DSC(x) (((u16)(x)<<12) & PHY_M_PC_DSC_MSK)
/* 100=5x; 101=6x; 110=7x; 111=8x */
enum {
MAC_TX_CLK_0_MHZ = 2,
PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */
};
-#define PHY_M_LED_PULS_DUR(x) (((x)<<12) & PHY_M_LEDC_PULS_MSK)
+#define PHY_M_LED_PULS_DUR(x) (((u16)(x)<<12) & PHY_M_LEDC_PULS_MSK)
/***** PHY_MARV_PHY_STAT (page 3)16 bit r/w Polarity Control Reg. *****/
enum {
PULS_1300MS = 7,/* 1.3 s to 2.7 s */
};
-#define PHY_M_LED_BLINK_RT(x) (((x)<<8) & PHY_M_LEDC_BL_R_MSK)
+#define PHY_M_LED_BLINK_RT(x) (((u16)(x)<<8) & PHY_M_LEDC_BL_R_MSK)
enum {
BLINK_42MS = 0,/* 42 ms */
BLINK_670MS = 4,/* 670 ms */
};
-/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
-#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
- /* Bit 13..12: reserved */
-#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
-#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
-#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
-#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
-#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
-#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
-
+/**** PHY_MARV_LED_OVER 16 bit r/w LED control */
enum {
- MO_LED_NORM = 0,
- MO_LED_BLINK = 1,
- MO_LED_OFF = 2,
- MO_LED_ON = 3,
+ PHY_M_LED_MO_DUP = 3<<10,/* Bit 11..10: Duplex */
+ PHY_M_LED_MO_10 = 3<<8, /* Bit 9.. 8: Link 10 */
+ PHY_M_LED_MO_100 = 3<<6, /* Bit 7.. 6: Link 100 */
+ PHY_M_LED_MO_1000 = 3<<4, /* Bit 5.. 4: Link 1000 */
+ PHY_M_LED_MO_RX = 3<<2, /* Bit 3.. 2: Rx */
+ PHY_M_LED_MO_TX = 3<<0, /* Bit 1.. 0: Tx */
+
+ PHY_M_LED_ALL = PHY_M_LED_MO_DUP | PHY_M_LED_MO_10
+ | PHY_M_LED_MO_100 | PHY_M_LED_MO_1000
+ | PHY_M_LED_MO_RX,
};
/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */
};
-#define PHY_M_FELP_LED2_CTRL(x) (((x)<<8) & PHY_M_FELP_LED2_MSK)
-#define PHY_M_FELP_LED1_CTRL(x) (((x)<<4) & PHY_M_FELP_LED1_MSK)
-#define PHY_M_FELP_LED0_CTRL(x) (((x)<<0) & PHY_M_FELP_LED0_MSK)
+#define PHY_M_FELP_LED2_CTRL(x) (((u16)(x)<<8) & PHY_M_FELP_LED2_MSK)
+#define PHY_M_FELP_LED1_CTRL(x) (((u16)(x)<<4) & PHY_M_FELP_LED1_MSK)
+#define PHY_M_FELP_LED0_CTRL(x) (((u16)(x)<<0) & PHY_M_FELP_LED0_MSK)
enum {
LED_PAR_CTRL_COLX = 0x00,
GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */
};
-#define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK)
-#define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK)
+#define GM_SMI_CT_PHY_AD(x) (((u16)(x)<<11) & GM_SMI_CT_PHY_A_MSK)
+#define GM_SMI_CT_REG_AD(x) (((u16)(x)<<6) & GM_SMI_CT_REG_A_MSK)
/* GM_PHY_ADDR 16 bit r/w GPHY Address Register */
enum {
Y2_ASF_CLR_ASFI = 1<<1, /* Clear host IRQ */
Y2_ASF_HOST_IRQ = 1<<0, /* Issue an IRQ to HOST system */
};
+/* HCU_CCSR CPU Control and Status Register */
+enum {
+ HCU_CCSR_SMBALERT_MONITOR= 1<<27, /* SMBALERT pin monitor */
+ HCU_CCSR_CPU_SLEEP = 1<<26, /* CPU sleep status */
+ /* Clock Stretching Timeout */
+ HCU_CCSR_CS_TO = 1<<25,
+ HCU_CCSR_WDOG = 1<<24, /* Watchdog Reset */
+
+ HCU_CCSR_CLR_IRQ_HOST = 1<<17, /* Clear IRQ_HOST */
+ HCU_CCSR_SET_IRQ_HCU = 1<<16, /* Set IRQ_HCU */
+
+ HCU_CCSR_AHB_RST = 1<<9, /* Reset AHB bridge */
+ HCU_CCSR_CPU_RST_MODE = 1<<8, /* CPU Reset Mode */
+
+ HCU_CCSR_SET_SYNC_CPU = 1<<5,
+ HCU_CCSR_CPU_CLK_DIVIDE_MSK = 3<<3,/* CPU Clock Divide */
+ HCU_CCSR_CPU_CLK_DIVIDE_BASE= 1<<3,
+ HCU_CCSR_OS_PRSNT = 1<<2, /* ASF OS Present */
+/* Microcontroller State */
+ HCU_CCSR_UC_STATE_MSK = 3,
+ HCU_CCSR_UC_STATE_BASE = 1<<0,
+ HCU_CCSR_ASF_RESET = 0,
+ HCU_CCSR_ASF_HALTED = 1<<1,
+ HCU_CCSR_ASF_RUNNING = 1<<0,
+};
+
+/* HCU_HCSR Host Control and Status Register */
+enum {
+ HCU_HCSR_SET_IRQ_CPU = 1<<16, /* Set IRQ_CPU */
+
+ HCU_HCSR_CLR_IRQ_HCU = 1<<1, /* Clear IRQ_HCU */
+ HCU_HCSR_SET_IRQ_HOST = 1<<0, /* Set IRQ_HOST */
+};
/* STAT_CTRL 32 bit Status BMU control register (Yukon-2 only) */
enum {
GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */
#define GMAC_DEF_MSK GM_IS_TX_FF_UR
+};
/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
- /* Bits 15.. 2: reserved */
+enum { /* Bits 15.. 2: reserved */
GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */
GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */
+};
/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */
+enum {
WOL_CTL_LINK_CHG_OCC = 1<<15,
WOL_CTL_MAGIC_PKT_OCC = 1<<14,
WOL_CTL_PATTERN_OCC = 1<<13,
WOL_CTL_DIS_PATTERN_UNIT = 1<<0,
};
-#define WOL_CTL_DEFAULT \
- (WOL_CTL_DIS_PME_ON_LINK_CHG | \
- WOL_CTL_DIS_PME_ON_PATTERN | \
- WOL_CTL_DIS_PME_ON_MAGIC_PKT | \
- WOL_CTL_DIS_LINK_CHG_UNIT | \
- WOL_CTL_DIS_PATTERN_UNIT | \
- WOL_CTL_DIS_MAGIC_PKT_UNIT)
-
-/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */
-#define WOL_CTL_PATT_ENA(x) (1 << (x))
-
/* Control flags */
enum {
u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
u8 rx_csum;
+ u8 wol;
enum flow_control flow_mode;
enum flow_control flow_status;
struct pci_dev *pdev;
struct net_device *dev[2];
- int pm_cap;
u8 chip_id;
u8 chip_rev;
u8 pmd_type;
dma_addr_t st_dma;
struct timer_list idle_timer;
- int msi_detected;
+ int msi;
wait_queue_head_t msi_wait;
};