static const char *yukon2_name[] = {
"XL", /* 0xb3 */
"EC Ultra", /* 0xb4 */
- "UNKNOWN", /* 0xb5 */
+ "Extreme", /* 0xb5 */
"EC", /* 0xb6 */
"FE", /* 0xb7 */
};
else
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
- if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) {
u32 reg1;
sky2_pci_write32(hw, PCI_DEV_REG3, 0);
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
u16 ctrl, ct1000, adv, pg, ledctrl, ledover, reg;
- if (sky2->autoneg == AUTONEG_ENABLE &&
- !(hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)) {
+ if (sky2->autoneg == AUTONEG_ENABLE
+ && !(hw->chip_id == CHIP_ID_YUKON_XL
+ || hw->chip_id == CHIP_ID_YUKON_EC_U
+ || hw->chip_id == CHIP_ID_YUKON_EX)) {
u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
/* enable automatic crossover */
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
- if (sky2->autoneg == AUTONEG_ENABLE &&
- (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)) {
+ if (sky2->autoneg == AUTONEG_ENABLE
+ && (hw->chip_id == CHIP_ID_YUKON_XL
+ || hw->chip_id == CHIP_ID_YUKON_EC_U
+ || hw->chip_id == CHIP_ID_YUKON_EX)) {
ctrl &= ~PHY_M_PC_DSC_MSK;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
}
/* restore page register */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
break;
+
case CHIP_ID_YUKON_EC_U:
+ case CHIP_ID_YUKON_EX:
pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
/* select page 3 to access LED control register */
/* set page register to 0 */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
- } else {
+ } else if (hw->chip_id != CHIP_ID_YUKON_EX) {
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
- if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) {
sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8);
sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8);
if (hw->dev[port]->mtu > ETH_DATA_LEN) {
sky2_write8(hw, SK_REG(port, LNK_LED_REG),
LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF);
- if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ if (hw->chip_id == CHIP_ID_YUKON_XL
+ || hw->chip_id == CHIP_ID_YUKON_EC_U
+ || hw->chip_id == CHIP_ID_YUKON_EX) {
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
u16 led = PHY_M_LEDC_LOS_CTRL(1); /* link active */
sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
/* Pause bits are offset (9..8) */
- if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)
+ if (hw->chip_id == CHIP_ID_YUKON_XL
+ || hw->chip_id == CHIP_ID_YUKON_EC_U
+ || hw->chip_id == CHIP_ID_YUKON_EX)
aux >>= 6;
sky2->flow_status = sky2_flow(aux & PHY_M_PS_RX_P_EN,
aux & PHY_M_PS_TX_P_EN);
if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
- && hw->chip_id != CHIP_ID_YUKON_EC_U)
+ && !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
sky2->flow_status = FC_NONE;
if (aux & PHY_M_PS_RX_P_EN)
}
-/* Transmit timeout is only called if we are running, carries is up
+/* Transmit timeout is only called if we are running, carrier is up
* and tx queue is full (stopped).
+ * Called with netif_tx_lock held.
*/
static void sky2_tx_timeout(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
- unsigned txq = txqaddr[sky2->port];
- u16 report, done;
+ u32 imask;
if (netif_msg_timer(sky2))
printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
- report = sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX);
- done = sky2_read16(hw, Q_ADDR(txq, Q_DONE));
-
printk(KERN_DEBUG PFX "%s: transmit ring %u .. %u report=%u done=%u\n",
- dev->name,
- sky2->tx_cons, sky2->tx_prod, report, done);
-
- if (report != done) {
- printk(KERN_INFO PFX "status burst pending (irq moderation?)\n");
+ dev->name, sky2->tx_cons, sky2->tx_prod,
+ sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX),
+ sky2_read16(hw, Q_ADDR(txqaddr[sky2->port], Q_DONE)));
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
- } else if (report != sky2->tx_cons) {
- printk(KERN_INFO PFX "status report lost?\n");
+ imask = sky2_read32(hw, B0_IMSK); /* block IRQ in hw */
+ sky2_write32(hw, B0_IMSK, 0);
+ sky2_read32(hw, B0_IMSK);
- netif_tx_lock_bh(dev);
- sky2_tx_complete(sky2, report);
- netif_tx_unlock_bh(dev);
- } else {
- printk(KERN_INFO PFX "hardware hung? flushing\n");
+ netif_poll_disable(hw->dev[0]); /* stop NAPI poll */
+ synchronize_irq(hw->pdev->irq);
- sky2_write32(hw, Q_ADDR(txq, Q_CSR), BMU_STOP);
- sky2_write32(hw, Y2_QADDR(txq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
+ netif_start_queue(dev); /* don't wakeup during flush */
+ sky2_tx_complete(sky2, sky2->tx_prod); /* Flush transmit queue */
- sky2_tx_clean(dev);
+ sky2_write32(hw, B0_IMSK, imask);
- sky2_qset(hw, txq);
- sky2_prefetch_init(hw, txq, sky2->tx_le_map, TX_RING_SIZE - 1);
- }
+ sky2_phy_reinit(sky2); /* this clears flow control etc */
}
static int sky2_change_mtu(struct net_device *dev, int new_mtu)
if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
return -EINVAL;
+ /* TSO on Yukon Ultra and MTU > 1500 not supported */
if (hw->chip_id == CHIP_ID_YUKON_EC_U && new_mtu > ETH_DATA_LEN)
- return -EINVAL;
+ dev->features &= ~NETIF_F_TSO;
if (!netif_running(dev)) {
dev->mtu = new_mtu;
pci_err = sky2_pci_read16(hw, PCI_STATUS);
if (net_ratelimit())
- printk(KERN_ERR PFX "%s: pci hw error (0x%x)\n",
- pci_name(hw->pdev), pci_err);
+ dev_err(&hw->pdev->dev, "PCI hardware error (0x%x)\n",
+ pci_err);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
sky2_pci_write16(hw, PCI_STATUS,
pex_err = sky2_pci_read32(hw, PEX_UNC_ERR_STAT);
if (net_ratelimit())
- printk(KERN_ERR PFX "%s: pci express error (0x%x)\n",
- pci_name(hw->pdev), pex_err);
+ dev_err(&hw->pdev->dev, "PCI Express error (0x%x)\n",
+ pex_err);
/* clear the interrupt */
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
switch (hw->chip_id) {
case CHIP_ID_YUKON_EC:
case CHIP_ID_YUKON_EC_U:
+ case CHIP_ID_YUKON_EX:
return 125; /* 125 Mhz */
case CHIP_ID_YUKON_FE:
return 100; /* 100 Mhz */
hw->chip_id = sky2_read8(hw, B2_CHIP_ID);
if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) {
- printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
- pci_name(hw->pdev), hw->chip_id);
+ dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n",
+ hw->chip_id);
return -EOPNOTSUPP;
}
+ if (hw->chip_id == CHIP_ID_YUKON_EX)
+ dev_warn(&hw->pdev->dev, "this driver not yet tested on this chip type\n"
+ "Please report success or failure to <netdev@vger.kernel.org>\n");
+
+ /* Make sure and enable all clocks */
+ if (hw->chip_id == CHIP_ID_YUKON_EX || hw->chip_id == CHIP_ID_YUKON_EC_U)
+ sky2_pci_write32(hw, PCI_DEV_REG3, 0);
+
hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4;
/* This rev is really old, and requires untested workarounds */
if (hw->chip_id == CHIP_ID_YUKON_EC && hw->chip_rev == CHIP_REV_YU_EC_A1) {
- printk(KERN_ERR PFX "%s: unsupported revision Yukon-%s (0x%x) rev %d\n",
- pci_name(hw->pdev), yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL],
- hw->chip_id, hw->chip_rev);
+ dev_err(&hw->pdev->dev, "unsupported revision Yukon-%s (0x%x) rev %d\n",
+ yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL],
+ hw->chip_id, hw->chip_rev);
return -EOPNOTSUPP;
}
/* disable ASF */
if (hw->chip_id <= CHIP_ID_YUKON_EC) {
- sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
+ if (hw->chip_id == CHIP_ID_YUKON_EX) {
+ status = sky2_read16(hw, HCU_CCSR);
+ status &= ~(HCU_CCSR_AHB_RST | HCU_CCSR_CPU_RST_MODE |
+ HCU_CCSR_UC_STATE_MSK);
+ sky2_write16(hw, HCU_CCSR, status);
+ } else
+ sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE);
}
struct net_device *dev = alloc_etherdev(sizeof(*sky2));
if (!dev) {
- printk(KERN_ERR "sky2 etherdev alloc failed");
+ dev_err(&hw->pdev->dev, "etherdev alloc failed");
return NULL;
}
sky2->port = port;
- if (hw->chip_id != CHIP_ID_YUKON_EC_U)
- dev->features |= NETIF_F_TSO;
+ dev->features |= NETIF_F_TSO | NETIF_F_IP_CSUM | NETIF_F_SG;
if (highmem)
dev->features |= NETIF_F_HIGHDMA;
- dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
#ifdef SKY2_VLAN_TAG_USED
dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
err = request_irq(pdev->irq, sky2_test_intr, 0, DRV_NAME, hw);
if (err) {
- printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
- pci_name(pdev), pdev->irq);
+ dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq);
return err;
}
if (!hw->msi) {
/* MSI test failed, go back to INTx mode */
- printk(KERN_INFO PFX "%s: No interrupt generated using MSI, "
- "switching to INTx mode.\n",
- pci_name(pdev));
+ dev_info(&pdev->dev, "No interrupt generated using MSI, "
+ "switching to INTx mode.\n");
err = -EOPNOTSUPP;
sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ);
err = pci_enable_device(pdev);
if (err) {
- printk(KERN_ERR PFX "%s cannot enable PCI device\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot enable PCI device\n");
goto err_out;
}
err = pci_request_regions(pdev, DRV_NAME);
if (err) {
- printk(KERN_ERR PFX "%s cannot obtain PCI resources\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot obtain PCI resources\n");
goto err_out;
}
using_dac = 1;
err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
if (err < 0) {
- printk(KERN_ERR PFX "%s unable to obtain 64 bit DMA "
- "for consistent allocations\n", pci_name(pdev));
+ dev_err(&pdev->dev, "unable to obtain 64 bit DMA "
+ "for consistent allocations\n");
goto err_out_free_regions;
}
-
} else {
err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (err) {
- printk(KERN_ERR PFX "%s no usable DMA configuration\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "no usable DMA configuration\n");
goto err_out_free_regions;
}
}
err = -ENOMEM;
hw = kzalloc(sizeof(*hw), GFP_KERNEL);
if (!hw) {
- printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot allocate hardware struct\n");
goto err_out_free_regions;
}
hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
if (!hw->regs) {
- printk(KERN_ERR PFX "%s: cannot map device registers\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot map device registers\n");
goto err_out_free_hw;
}
if (err)
goto err_out_iounmap;
- printk(KERN_INFO PFX "v%s addr 0x%llx irq %d Yukon-%s (0x%x) rev %d\n",
+ dev_info(&pdev->dev, "v%s addr 0x%llx irq %d Yukon-%s (0x%x) rev %d\n",
DRV_VERSION, (unsigned long long)pci_resource_start(pdev, 0),
pdev->irq, yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL],
hw->chip_id, hw->chip_rev);
err = register_netdev(dev);
if (err) {
- printk(KERN_ERR PFX "%s: cannot register net device\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot register net device\n");
goto err_out_free_netdev;
}
err = request_irq(pdev->irq, sky2_intr, hw->msi ? 0 : IRQF_SHARED,
dev->name, hw);
if (err) {
- printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
- pci_name(pdev), pdev->irq);
+ dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq);
goto err_out_unregister;
}
sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
struct net_device *dev1;
dev1 = sky2_init_netdev(hw, 1, using_dac, wol_default);
- if (!dev1) {
- printk(KERN_WARNING PFX
- "allocation of second port failed\n");
- }
- else if (!(err = register_netdev(dev1)))
- sky2_show_addr(dev1);
- else {
- printk(KERN_WARNING PFX
- "register of second port failed (%d)\n", err);
+ if (!dev1)
+ dev_warn(&pdev->dev, "allocation for second device failed\n");
+ else if ((err = register_netdev(dev1))) {
+ dev_warn(&pdev->dev,
+ "register of second port failed (%d)\n", err);
hw->dev[1] = NULL;
free_netdev(dev1);
- }
+ } else
+ sky2_show_addr(dev1);
}
setup_timer(&hw->idle_timer, sky2_idle, (unsigned long) hw);
sky2_idle_start(hw);
return 0;
out:
- printk(KERN_ERR PFX "%s: resume failed (%d)\n", pci_name(pdev), err);
+ dev_err(&pdev->dev, "resume failed (%d)\n", err);
pci_disable_device(pdev);
return err;
}