* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-/*
- * TOTEST
- * - speed setting
- * - suspend/resume
- */
-
#include <linux/config.h>
#include <linux/crc32.h>
#include <linux/kernel.h>
#include "sky2.h"
#define DRV_NAME "sky2"
-#define DRV_VERSION "0.12"
+#define DRV_VERSION "0.15"
#define PFX DRV_NAME " "
/*
#define TX_RING_SIZE 512
#define TX_DEF_PENDING (TX_RING_SIZE - 1)
#define TX_MIN_PENDING 64
-#define MAX_SKB_TX_LE (4 + 2*MAX_SKB_FRAGS)
+#define MAX_SKB_TX_LE (4 + (sizeof(dma_addr_t)/sizeof(u32))*MAX_SKB_FRAGS)
#define STATUS_RING_SIZE 2048 /* 2 ports * (TX + 2*RX) */
#define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le))
static const u32 default_msg =
NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK
| NETIF_MSG_TIMER | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR
- | NETIF_MSG_IFUP | NETIF_MSG_IFDOWN | NETIF_MSG_INTR;
+ | NETIF_MSG_IFUP | NETIF_MSG_IFDOWN;
static int debug = -1; /* defaults above */
module_param(debug, int, 0);
pr_debug("sky2_set_power_state %d\n", state);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_PMC, &power_control);
- vaux = (sky2_read8(hw, B0_CTST) & Y2_VAUX_AVAIL) &&
+ power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_PMC);
+ vaux = (sky2_read16(hw, B0_CTST) & Y2_VAUX_AVAIL) &&
(power_control & PCI_PM_CAP_PME_D3cold);
- pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_CTRL, &power_control);
+ power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_CTRL);
power_control |= PCI_PM_CTRL_PME_STATUS;
power_control &= ~(PCI_PM_CTRL_STATE_MASK);
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
/* Turn off phy power saving */
- pci_read_config_dword(hw->pdev, PCI_DEV_REG1, ®1);
+ reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
/* looks like this XL is back asswards .. */
if (hw->ports > 1)
reg1 |= PCI_Y2_PHY2_COMA;
}
- pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ sky2_pci_write32(hw, PCI_DEV_REG3, 0);
+ reg1 = sky2_pci_read32(hw, PCI_DEV_REG4);
+ reg1 &= P_ASPM_CONTROL_MSK;
+ sky2_pci_write32(hw, PCI_DEV_REG4, reg1);
+ sky2_pci_write32(hw, PCI_DEV_REG5, 0);
+ }
+
+ sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
+
break;
case PCI_D3hot:
case PCI_D3cold:
/* Turn on phy power saving */
- pci_read_config_dword(hw->pdev, PCI_DEV_REG1, ®1);
+ reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
else
reg1 |= (PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
- pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+ sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
ret = -1;
}
- pci_write_config_byte(hw->pdev, hw->pm_cap + PCI_PM_CTRL, power_control);
+ sky2_pci_write16(hw, hw->pm_cap + PCI_PM_CTRL, power_control);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
return ret;
}
ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
}
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+ /* apply fixes in PHY AFE */
+ gm_phy_write(hw, port, 22, 255);
+ /* increase differential signal amplitude in 10BASE-T */
+ gm_phy_write(hw, port, 24, 0xaa99);
+ gm_phy_write(hw, port, 23, 0x2011);
- if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
- /* turn on 100 Mbps LED (LED_LINK100) */
- ledover |= PHY_M_LED_MO_100(MO_LED_ON);
- }
+ /* fix for IEEE A/B Symmetry failure in 1000BASE-T */
+ gm_phy_write(hw, port, 24, 0xa204);
+ gm_phy_write(hw, port, 23, 0x2002);
- if (ledover)
- gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+ /* set page register to 0 */
+ gm_phy_write(hw, port, 22, 0);
+ } else {
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+
+ if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
+ /* turn on 100 Mbps LED (LED_LINK100) */
+ ledover |= PHY_M_LED_MO_100(MO_LED_ON);
+ }
+ if (ledover)
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+
+ }
/* Enable phy interrupt on auto-negotiation complete (or link up) */
if (sky2->autoneg == AUTONEG_ENABLE)
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
switch (sky2->speed) {
case SPEED_1000:
+ reg &= ~GM_GPCR_SPEED_100;
reg |= GM_GPCR_SPEED_1000;
- /* fallthru */
+ break;
case SPEED_100:
+ reg &= ~GM_GPCR_SPEED_1000;
reg |= GM_GPCR_SPEED_100;
+ break;
+ case SPEED_10:
+ reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
+ break;
}
if (sky2->duplex == DUPLEX_FULL)
/* Configure Rx MAC FIFO */
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
- sky2_write16(hw, SK_REG(port, RX_GMF_CTRL_T),
- GMF_RX_CTRL_DEF);
+ sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T),
+ GMF_OPER_ON | GMF_RX_F_FL_ON);
/* Flush Rx MAC FIFO on any flow control or error */
sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR);
}
-static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, size_t len)
+/* Assign Ram Buffer allocation.
+ * start and end are in units of 4k bytes
+ * ram registers are in units of 64bit words
+ */
+static void sky2_ramset(struct sky2_hw *hw, u16 q, u8 startk, u8 endk)
{
- u32 end;
+ u32 start, end;
- start /= 8;
- len /= 8;
- end = start + len - 1;
+ start = startk * 4096/8;
+ end = (endk * 4096/8) - 1;
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
sky2_write32(hw, RB_ADDR(q, RB_START), start);
sky2_write32(hw, RB_ADDR(q, RB_RP), start);
if (q == Q_R1 || q == Q_R2) {
- u32 rxup, rxlo;
+ u32 space = (endk - startk) * 4096/8;
+ u32 tp = space - space/4;
- rxlo = len/2;
- rxup = rxlo + len/4;
+ /* On receive queue's set the thresholds
+ * give receiver priority when > 3/4 full
+ * send pause when down to 2K
+ */
+ sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp);
+ sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2);
- /* Set thresholds on receive queue's */
- sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), rxup);
- sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), rxlo);
+ tp = space - 2048/8;
+ sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp);
+ sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4);
} else {
/* Enable store & forward on Tx queue's because
* Tx FIFO is only 1K on Yukon
* This is a workaround code taken from SysKonnect sk98lin driver
* to deal with chip bug on Yukon EC rev 0 in the wraparound case.
*/
-static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q,
+static void sky2_put_idx(struct sky2_hw *hw, unsigned q,
u16 idx, u16 *last, u16 size)
{
+ wmb();
if (is_ec_a1(hw) && idx < *last) {
u16 hwget = sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_GET_IDX));
sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx);
}
*last = idx;
+ mmiowb();
}
/* Return high part of DMA address (could be 32 or 64 bit) */
static inline u32 high32(dma_addr_t a)
{
- return (a >> 16) >> 16;
+ return sizeof(a) > sizeof(u32) ? (a >> 16) >> 16 : 0;
}
/* Build description to hardware about buffer */
-static inline void sky2_rx_add(struct sky2_port *sky2, dma_addr_t map)
+static void sky2_rx_add(struct sky2_port *sky2, dma_addr_t map)
{
struct sky2_rx_le *le;
u32 hi = high32(map);
struct sky2_hw *hw = sky2->hw;
u16 port = sky2->port;
- spin_lock(&sky2->tx_lock);
+ spin_lock_bh(&sky2->tx_lock);
sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_ON);
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_ON);
sky2->vlgrp = grp;
- spin_unlock(&sky2->tx_lock);
+ spin_unlock_bh(&sky2->tx_lock);
}
static void sky2_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
struct sky2_hw *hw = sky2->hw;
u16 port = sky2->port;
- spin_lock(&sky2->tx_lock);
+ spin_lock_bh(&sky2->tx_lock);
sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_OFF);
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_OFF);
if (sky2->vlgrp)
sky2->vlgrp->vlan_devices[vid] = NULL;
- spin_unlock(&sky2->tx_lock);
+ spin_unlock_bh(&sky2->tx_lock);
}
#endif
sky2->rx_put = sky2->rx_next = 0;
sky2_qset(hw, rxq);
+
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+ /* MAC Rx RAM Read is controlled by hardware */
+ sky2_write32(hw, Q_ADDR(rxq, Q_F), F_M_RX_RAM_DIS);
+ }
+
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
rx_set_checksum(sky2);
sky2_rx_add(sky2, re->mapaddr);
}
+ /* Truncate oversize frames */
+ sky2_write16(hw, SK_REG(sky2->port, RX_GMF_TR_THR), sky2->rx_bufsize - 8);
+ sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_ON);
+
/* Tell chip about available buffers */
sky2_write16(hw, Y2_QADDR(rxq, PREF_UNIT_PUT_IDX), sky2->rx_put);
sky2->rx_last_put = sky2_read16(hw, Y2_QADDR(rxq, PREF_UNIT_PUT_IDX));
sky2_mac_init(hw, port);
- /* Configure RAM buffers */
- if (hw->chip_id == CHIP_ID_YUKON_FE ||
- (hw->chip_id == CHIP_ID_YUKON_EC && hw->chip_rev == 2))
- ramsize = 4096;
- else {
- u8 e0 = sky2_read8(hw, B2_E_0);
- ramsize = (e0 == 0) ? (128 * 1024) : (e0 * 4096);
- }
+ /* Determine available ram buffer space (in 4K blocks).
+ * Note: not sure about the FE setting below yet
+ */
+ if (hw->chip_id == CHIP_ID_YUKON_FE)
+ ramsize = 4;
+ else
+ ramsize = sky2_read8(hw, B2_E_0);
+
+ /* Give transmitter one third (rounded up) */
+ rxspace = ramsize - (ramsize + 2) / 3;
- /* 2/3 for Rx */
- rxspace = (2 * ramsize) / 3;
sky2_ramset(hw, rxqaddr[port], 0, rxspace);
- sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace);
+ sky2_ramset(hw, txqaddr[port], rxspace, ramsize);
/* Make sure SyncQ is disabled */
sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL),
RB_RST_SET);
sky2_qset(hw, txqaddr[port]);
- if (hw->chip_id == CHIP_ID_YUKON_EC_U)
- sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
+ /* Set almost empty threshold */
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == 1)
+ sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
TX_RING_SIZE - 1);
goto err_out;
/* Enable interrupts from phy/mac for port */
+ spin_lock_irq(&hw->hw_lock);
hw->intr_mask |= (port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
+ spin_unlock_irq(&hw->hw_lock);
return 0;
err_out:
}
/* Estimate of number of transmit list elements required */
-static inline unsigned tx_le_req(const struct sk_buff *skb)
+static unsigned tx_le_req(const struct sk_buff *skb)
{
unsigned count;
struct sky2_tx_le *le = NULL;
struct tx_ring_info *re;
unsigned i, len;
+ int avail;
dma_addr_t mapping;
u32 addr64;
u16 mss;
u8 ctrl;
+ /* No BH disabling for tx_lock here. We are running in BH disabled
+ * context and TX reclaim runs via poll inside of a software
+ * interrupt, and no related locks in IRQ processing.
+ */
if (!spin_trylock(&sky2->tx_lock))
return NETDEV_TX_LOCKED;
*/
if (!netif_queue_stopped(dev)) {
netif_stop_queue(dev);
- printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
- dev->name);
+ if (net_ratelimit())
+ printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
+ dev->name);
}
spin_unlock(&sky2->tx_lock);
mapping = pci_map_page(hw->pdev, frag->page, frag->page_offset,
frag->size, PCI_DMA_TODEVICE);
- addr64 = (mapping >> 16) >> 16;
+ addr64 = high32(mapping);
if (addr64 != sky2->tx_addr64) {
le = get_tx_le(sky2);
le->tx.addr = cpu_to_le32(addr64);
re->idx = sky2->tx_prod;
le->ctrl |= EOP;
+ avail = tx_avail(sky2);
+ if (mss != 0 || avail < TX_MIN_PENDING) {
+ le->ctrl |= FRC_STAT;
+ if (avail <= MAX_SKB_TX_LE)
+ netif_stop_queue(dev);
+ }
+
sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod,
&sky2->tx_last_put, TX_RING_SIZE);
- if (tx_avail(sky2) <= MAX_SKB_TX_LE)
- netif_stop_queue(dev);
-
out_unlock:
- mmiowb();
spin_unlock(&sky2->tx_lock);
dev->trans_start = jiffies;
dev_kfree_skb_any(skb);
}
- spin_lock(&sky2->tx_lock);
sky2->tx_cons = put;
if (netif_queue_stopped(dev) && tx_avail(sky2) > MAX_SKB_TX_LE)
netif_wake_queue(dev);
- spin_unlock(&sky2->tx_lock);
}
/* Cleanup all untransmitted buffers, assume transmitter not running */
static void sky2_tx_clean(struct sky2_port *sky2)
{
+ spin_lock_bh(&sky2->tx_lock);
sky2_tx_complete(sky2, sky2->tx_prod);
+ spin_unlock_bh(&sky2->tx_lock);
}
/* Network shutdown */
netif_stop_queue(dev);
/* Disable port IRQ */
- local_irq_disable();
+ spin_lock_irq(&hw->hw_lock);
hw->intr_mask &= ~((sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
sky2_write32(hw, B0_IMSK, hw->intr_mask);
- local_irq_enable();
+ spin_unlock_irq(&hw->hw_lock);
flush_scheduled_work();
sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
reg = gma_read16(hw, port, GM_GP_CTRL);
+ if (sky2->autoneg == AUTONEG_DISABLE) {
+ reg |= GM_GPCR_AU_ALL_DIS;
+
+ /* Is write/read necessary? Copied from sky2_mac_init */
+ gma_write16(hw, port, GM_GP_CTRL, reg);
+ gma_read16(hw, port, GM_GP_CTRL);
+
+ switch (sky2->speed) {
+ case SPEED_1000:
+ reg &= ~GM_GPCR_SPEED_100;
+ reg |= GM_GPCR_SPEED_1000;
+ break;
+ case SPEED_100:
+ reg &= ~GM_GPCR_SPEED_1000;
+ reg |= GM_GPCR_SPEED_100;
+ break;
+ case SPEED_10:
+ reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
+ break;
+ }
+ } else
+ reg &= ~GM_GPCR_AU_ALL_DIS;
+
if (sky2->duplex == DUPLEX_FULL || sky2->autoneg == AUTONEG_ENABLE)
reg |= GM_GPCR_DUP_FULL;
out:
up(&sky2->phy_sema);
- local_irq_disable();
+ spin_lock_irq(&hw->hw_lock);
hw->intr_mask |= (sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
- local_irq_enable();
+ spin_unlock_irq(&hw->hw_lock);
}
+
+/* Transmit timeout is only called if we are running, carries is up
+ * and tx queue is full (stopped).
+ */
static void sky2_tx_timeout(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned txq = txqaddr[sky2->port];
+ u16 ridx;
+
+ /* Maybe we just missed an status interrupt */
+ spin_lock(&sky2->tx_lock);
+ ridx = sky2_read16(hw,
+ sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX);
+ sky2_tx_complete(sky2, ridx);
+ spin_unlock(&sky2->tx_lock);
+
+ if (!netif_queue_stopped(dev)) {
+ if (net_ratelimit())
+ pr_info(PFX "transmit interrupt missed? recovered\n");
+ return;
+ }
if (netif_msg_timer(sky2))
printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
- netif_stop_queue(dev);
-
sky2_write32(hw, Q_ADDR(txq, Q_CSR), BMU_STOP);
- sky2_read32(hw, Q_ADDR(txq, Q_CSR));
-
sky2_write32(hw, Y2_QADDR(txq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
sky2_tx_clean(sky2);
sky2_qset(hw, txq);
sky2_prefetch_init(hw, txq, sky2->tx_le_map, TX_RING_SIZE - 1);
-
- netif_wake_queue(dev);
}
#define roundup(x, y) ((((x)+((y)-1))/(y))*(y))
-/* Want receive buffer size to be multiple of 64 bits, and incl room for vlan */
+/* Want receive buffer size to be multiple of 64 bits
+ * and incl room for vlan and truncation
+ */
static inline unsigned sky2_buf_size(int mtu)
{
- return roundup(mtu + ETH_HLEN + 4, 8);
+ return roundup(mtu + ETH_HLEN + VLAN_HLEN, 8) + 8;
}
static int sky2_change_mtu(struct net_device *dev, int new_mtu)
if (!(status & GMR_FS_RX_OK))
goto resubmit;
- if ((status >> 16) != length || length > sky2->rx_bufsize)
+ if (length > sky2->netdev->mtu + ETH_HLEN)
goto oversize;
if (length < copybreak) {
error:
++sky2->net_stats.rx_errors;
- if (netif_msg_rx_err(sky2))
+ if (netif_msg_rx_err(sky2) && net_ratelimit())
printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n",
sky2->netdev->name, status, length);
*/
#define TX_NO_STATUS 0xffff
-static inline void sky2_tx_check(struct sky2_hw *hw, int port, u16 last)
+static void sky2_tx_check(struct sky2_hw *hw, int port, u16 last)
{
if (last != TX_NO_STATUS) {
struct net_device *dev = hw->dev[port];
if (dev && netif_running(dev)) {
struct sky2_port *sky2 = netdev_priv(dev);
+
+ spin_lock(&sky2->tx_lock);
sky2_tx_complete(sky2, last);
+ spin_unlock(&sky2->tx_lock);
}
}
}
u16 hwidx;
u16 tx_done[2] = { TX_NO_STATUS, TX_NO_STATUS };
+ sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
+
+ /*
+ * Kick the STAT_LEV_TIMER_CTRL timer.
+ * This fixes my hangs on Yukon-EC (0xb6) rev 1.
+ * The if clause is there to start the timer only if it has been
+ * configured correctly and not been disabled via ethtool.
+ */
+ if (sky2_read8(hw, STAT_LEV_TIMER_CTRL) == TIM_START) {
+ sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_STOP);
+ sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
+ }
+
hwidx = sky2_read16(hw, STAT_PUT_IDX);
BUG_ON(hwidx >= STATUS_RING_SIZE);
rmb();
struct sk_buff *skb;
u32 status;
u16 length;
- u8 op;
le = hw->st_le + hw->st_idx;
hw->st_idx = (hw->st_idx + 1) % STATUS_RING_SIZE;
sky2 = netdev_priv(dev);
status = le32_to_cpu(le->status);
length = le16_to_cpu(le->length);
- op = le->opcode & ~HW_OWNER;
- le->opcode = 0;
- switch (op) {
+ switch (le->opcode & ~HW_OWNER) {
case OP_RXSTAT:
skb = sky2_receive(sky2, length, status);
if (!skb)
default:
if (net_ratelimit())
printk(KERN_WARNING PFX
- "unknown status opcode 0x%x\n", op);
+ "unknown status opcode 0x%x\n", le->opcode);
break;
}
}
exit_loop:
- sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
- mmiowb();
-
sky2_tx_check(hw, 0, tx_done[0]);
sky2_tx_check(hw, 1, tx_done[1]);
- if (sky2_read16(hw, STAT_PUT_IDX) == hw->st_idx) {
- /* need to restart TX timer */
- if (is_ec_a1(hw)) {
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
- }
+ if (sky2_read8(hw, STAT_TX_TIMER_CTRL) == TIM_START) {
+ sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
+ sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
+ }
+
+ if (likely(work_done < to_do)) {
+ spin_lock_irq(&hw->hw_lock);
+ __netif_rx_complete(dev0);
- netif_rx_complete(dev0);
hw->intr_mask |= Y2_IS_STAT_BMU;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
- mmiowb();
+ spin_unlock_irq(&hw->hw_lock);
+
return 0;
} else {
*budget -= work_done;
{
struct net_device *dev = hw->dev[port];
- printk(KERN_INFO PFX "%s: hw error interrupt status 0x%x\n",
- dev->name, status);
+ if (net_ratelimit())
+ printk(KERN_INFO PFX "%s: hw error interrupt status 0x%x\n",
+ dev->name, status);
if (status & Y2_IS_PAR_RD1) {
- printk(KERN_ERR PFX "%s: ram data read parity error\n",
- dev->name);
+ if (net_ratelimit())
+ printk(KERN_ERR PFX "%s: ram data read parity error\n",
+ dev->name);
/* Clear IRQ */
sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_RD_PERR);
}
if (status & Y2_IS_PAR_WR1) {
- printk(KERN_ERR PFX "%s: ram data write parity error\n",
- dev->name);
+ if (net_ratelimit())
+ printk(KERN_ERR PFX "%s: ram data write parity error\n",
+ dev->name);
sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_WR_PERR);
}
if (status & Y2_IS_PAR_MAC1) {
- printk(KERN_ERR PFX "%s: MAC parity error\n", dev->name);
+ if (net_ratelimit())
+ printk(KERN_ERR PFX "%s: MAC parity error\n", dev->name);
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_PE);
}
if (status & Y2_IS_PAR_RX1) {
- printk(KERN_ERR PFX "%s: RX parity error\n", dev->name);
+ if (net_ratelimit())
+ printk(KERN_ERR PFX "%s: RX parity error\n", dev->name);
sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), BMU_CLR_IRQ_PAR);
}
if (status & Y2_IS_TCP_TXA1) {
- printk(KERN_ERR PFX "%s: TCP segmentation error\n", dev->name);
+ if (net_ratelimit())
+ printk(KERN_ERR PFX "%s: TCP segmentation error\n",
+ dev->name);
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_CLR_IRQ_TCP);
}
}
if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) {
u16 pci_err;
- pci_read_config_word(hw->pdev, PCI_STATUS, &pci_err);
- printk(KERN_ERR PFX "%s: pci hw error (0x%x)\n",
- pci_name(hw->pdev), pci_err);
+ pci_err = sky2_pci_read16(hw, PCI_STATUS);
+ if (net_ratelimit())
+ printk(KERN_ERR PFX "%s: pci hw error (0x%x)\n",
+ pci_name(hw->pdev), pci_err);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_write_config_word(hw->pdev, PCI_STATUS,
+ sky2_pci_write16(hw, PCI_STATUS,
pci_err | PCI_STATUS_ERROR_BITS);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
/* PCI-Express uncorrectable Error occurred */
u32 pex_err;
- pci_read_config_dword(hw->pdev, PEX_UNC_ERR_STAT, &pex_err);
+ pex_err = sky2_pci_read32(hw, PEX_UNC_ERR_STAT);
- printk(KERN_ERR PFX "%s: pci express error (0x%x)\n",
- pci_name(hw->pdev), pex_err);
+ if (net_ratelimit())
+ printk(KERN_ERR PFX "%s: pci express error (0x%x)\n",
+ pci_name(hw->pdev), pex_err);
/* clear the interrupt */
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
+ sky2_pci_write32(hw, PEX_UNC_ERR_STAT,
0xffffffffUL);
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
hw->intr_mask &= ~(port == 0 ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
sky2_write32(hw, B0_IMSK, hw->intr_mask);
+
schedule_work(&sky2->phy_task);
}
if (status == 0 || status == ~0)
return IRQ_NONE;
+ spin_lock(&hw->hw_lock);
if (status & Y2_IS_HW_ERR)
sky2_hw_intr(hw);
sky2_write32(hw, B0_Y2_SP_ICR, 2);
- sky2_read32(hw, B0_IMSK);
+ spin_unlock(&hw->hw_lock);
return IRQ_HANDLED;
}
static int sky2_reset(struct sky2_hw *hw)
{
- u32 ctst;
u16 status;
u8 t8, pmd_type;
int i;
- ctst = sky2_read32(hw, B0_CTST);
-
sky2_write8(hw, B0_CTST, CS_RST_CLR);
+
hw->chip_id = sky2_read8(hw, B2_CHIP_ID);
if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) {
printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
return -EOPNOTSUPP;
}
- /* ring for status responses */
- hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES,
- &hw->st_dma);
- if (!hw->st_le)
- return -ENOMEM;
-
/* disable ASF */
if (hw->chip_id <= CHIP_ID_YUKON_EC) {
sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
sky2_write8(hw, B0_CTST, CS_RST_CLR);
/* clear PCI errors, if any */
- pci_read_config_word(hw->pdev, PCI_STATUS, &status);
+ status = sky2_pci_read16(hw, PCI_STATUS);
+
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_write_config_word(hw->pdev, PCI_STATUS,
- status | PCI_STATUS_ERROR_BITS);
+ sky2_pci_write16(hw, PCI_STATUS, status | PCI_STATUS_ERROR_BITS);
+
sky2_write8(hw, B0_CTST, CS_MRST_CLR);
/* clear any PEX errors */
- if (is_pciex(hw)) {
- u16 lstat;
- pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
- 0xffffffffUL);
- pci_read_config_word(hw->pdev, PEX_LNK_STAT, &lstat);
- }
+ if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP))
+ sky2_pci_write32(hw, PEX_UNC_ERR_STAT, 0xffffffffUL);
+
pmd_type = sky2_read8(hw, B2_PMD_TYP);
hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
sky2_write8(hw, STAT_FIFO_ISR_WM, 16);
sky2_write32(hw, STAT_TX_TIMER_INI, sky2_us2clk(hw, 1000));
- sky2_write32(hw, STAT_LEV_TIMER_INI, sky2_us2clk(hw, 100));
- sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 20));
+ sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 7));
}
/* enable status unit */
return 0;
}
-static inline u32 sky2_supported_modes(const struct sky2_hw *hw)
+static u32 sky2_supported_modes(const struct sky2_hw *hw)
{
u32 modes;
if (hw->copper) {
static int sky2_set_mac_address(struct net_device *dev, void *p)
{
struct sky2_port *sky2 = netdev_priv(dev);
- struct sockaddr *addr = p;
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ const struct sockaddr *addr = p;
if (!is_valid_ether_addr(addr->sa_data))
return -EADDRNOTAVAIL;
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
- memcpy_toio(sky2->hw->regs + B2_MAC_1 + sky2->port * 8,
+ memcpy_toio(hw->regs + B2_MAC_1 + port * 8,
dev->dev_addr, ETH_ALEN);
- memcpy_toio(sky2->hw->regs + B2_MAC_2 + sky2->port * 8,
+ memcpy_toio(hw->regs + B2_MAC_2 + port * 8,
dev->dev_addr, ETH_ALEN);
- if (netif_running(dev))
- sky2_phy_reinit(sky2);
+ /* virtual address for data */
+ gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr);
+
+ /* physical address: used for pause frames */
+ gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr);
return 0;
}
(ecmd->rx_coalesce_usecs_irq < tmin || ecmd->rx_coalesce_usecs_irq > tmax))
return -EINVAL;
- if (ecmd->tx_max_coalesced_frames > 0xffff)
+ if (ecmd->tx_max_coalesced_frames >= TX_RING_SIZE-1)
return -EINVAL;
- if (ecmd->rx_max_coalesced_frames > 0xff)
+ if (ecmd->rx_max_coalesced_frames > RX_MAX_PENDING)
return -EINVAL;
- if (ecmd->rx_max_coalesced_frames_irq > 0xff)
+ if (ecmd->rx_max_coalesced_frames_irq >RX_MAX_PENDING)
return -EINVAL;
if (ecmd->tx_coalesce_usecs == 0)
if (ecmd->rx_coalesce_usecs_irq == 0)
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_STOP);
else {
- sky2_write32(hw, STAT_TX_TIMER_INI,
+ sky2_write32(hw, STAT_ISR_TIMER_INI,
sky2_us2clk(hw, ecmd->rx_coalesce_usecs_irq));
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
}
return dev;
}
-static inline void sky2_show_addr(struct net_device *dev)
+static void __devinit sky2_show_addr(struct net_device *dev)
{
const struct sky2_port *sky2 = netdev_priv(dev);
}
}
-#ifdef __BIG_ENDIAN
- /* byte swap descriptors in hardware */
- {
- u32 reg;
-
- pci_read_config_dword(pdev, PCI_DEV_REG2, ®);
- reg |= PCI_REV_DESC;
- pci_write_config_dword(pdev, PCI_DEV_REG2, reg);
- }
-#endif
-
err = -ENOMEM;
- hw = kmalloc(sizeof(*hw), GFP_KERNEL);
+ hw = kzalloc(sizeof(*hw), GFP_KERNEL);
if (!hw) {
printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
pci_name(pdev));
goto err_out_free_regions;
}
- memset(hw, 0, sizeof(*hw));
hw->pdev = pdev;
hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
goto err_out_free_hw;
}
hw->pm_cap = pm_cap;
+ spin_lock_init(&hw->hw_lock);
+
+#ifdef __BIG_ENDIAN
+ /* byte swap descriptors in hardware */
+ {
+ u32 reg;
+
+ reg = sky2_pci_read32(hw, PCI_DEV_REG2);
+ reg |= PCI_REV_DESC;
+ sky2_pci_write32(hw, PCI_DEV_REG2, reg);
+ }
+#endif
+
+ /* ring for status responses */
+ hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES,
+ &hw->st_dma);
+ if (!hw->st_le)
+ goto err_out_iounmap;
err = sky2_reset(hw);
if (err)
static int sky2_resume(struct pci_dev *pdev)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
- int i;
+ int i, err;
pci_restore_state(pdev);
pci_enable_wake(pdev, PCI_D0, 0);
- sky2_set_power_state(hw, PCI_D0);
+ err = sky2_set_power_state(hw, PCI_D0);
+ if (err)
+ goto out;
- sky2_reset(hw);
+ err = sky2_reset(hw);
+ if (err)
+ goto out;
for (i = 0; i < 2; i++) {
struct net_device *dev = hw->dev[i];
- if (dev) {
- if (netif_running(dev)) {
- netif_device_attach(dev);
- if (sky2_up(dev))
- dev_close(dev);
+ if (dev && netif_running(dev)) {
+ netif_device_attach(dev);
+ err = sky2_up(dev);
+ if (err) {
+ printk(KERN_ERR PFX "%s: could not up: %d\n",
+ dev->name, err);
+ dev_close(dev);
+ break;
}
}
}
- return 0;
+out:
+ return err;
}
#endif