#include "sky2.h"
#define DRV_NAME "sky2"
-#define DRV_VERSION "1.21"
+#define DRV_VERSION "1.22"
#define PFX DRV_NAME " "
/*
module_param(disable_msi, int, 0);
MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)");
-static const struct pci_device_id sky2_id_table[] = {
+static DEFINE_PCI_DEVICE_TABLE(sky2_id_table) = {
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, /* SK-9Sxx */
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) }, /* DGE-560T */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) }, /* 88E8038 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4353) }, /* 88E8039 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4354) }, /* 88E8040 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4355) }, /* 88E8040T */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4356) }, /* 88EC033 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4357) }, /* 88E8042 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x435A) }, /* 88E8048 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436C) }, /* 88E8072 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436D) }, /* 88E8055 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4370) }, /* 88E8075 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4380) }, /* 88E8057 */
{ 0 }
};
static const unsigned rxqaddr[] = { Q_R1, Q_R2 };
static const u32 portirq_msk[] = { Y2_IS_PORT_1, Y2_IS_PORT_2 };
-/* This driver supports yukon2 chipset only */
-static const char *yukon2_name[] = {
- "XL", /* 0xb3 */
- "EC Ultra", /* 0xb4 */
- "Extreme", /* 0xb5 */
- "EC", /* 0xb6 */
- "FE", /* 0xb7 */
- "FE+", /* 0xb8 */
- "Supreme", /* 0xb9 */
-};
-
static void sky2_set_multicast(struct net_device *dev);
/* Access to PHY via serial interconnect */
PC_VAUX_ON | PC_VCC_OFF));
}
+static void sky2_power_state(struct sky2_hw *hw, pci_power_t state)
+{
+ u16 power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_CTRL);
+ int pex = pci_find_capability(hw->pdev, PCI_CAP_ID_EXP);
+ u32 reg;
+
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+
+ switch (state) {
+ case PCI_D0:
+ break;
+
+ case PCI_D1:
+ power_control |= 1;
+ break;
+
+ case PCI_D2:
+ power_control |= 2;
+ break;
+
+ case PCI_D3hot:
+ case PCI_D3cold:
+ power_control |= 3;
+ if (hw->flags & SKY2_HW_ADV_POWER_CTL) {
+ /* additional power saving measurements */
+ reg = sky2_pci_read32(hw, PCI_DEV_REG4);
+
+ /* set gating core clock for LTSSM in L1 state */
+ reg |= P_PEX_LTSSM_STAT(P_PEX_LTSSM_L1_STAT) |
+ /* auto clock gated scheme controlled by CLKREQ */
+ P_ASPM_A1_MODE_SELECT |
+ /* enable Gate Root Core Clock */
+ P_CLK_GATE_ROOT_COR_ENA;
+
+ if (pex && (hw->flags & SKY2_HW_CLK_POWER)) {
+ /* enable Clock Power Management (CLKREQ) */
+ u16 ctrl = sky2_pci_read16(hw, pex + PCI_EXP_DEVCTL);
+
+ ctrl |= PCI_EXP_DEVCTL_AUX_PME;
+ sky2_pci_write16(hw, pex + PCI_EXP_DEVCTL, ctrl);
+ } else
+ /* force CLKREQ Enable in Our4 (A1b only) */
+ reg |= P_ASPM_FORCE_CLKREQ_ENA;
+
+ /* set Mask Register for Release/Gate Clock */
+ sky2_pci_write32(hw, PCI_DEV_REG5,
+ P_REL_PCIE_EXIT_L1_ST | P_GAT_PCIE_ENTER_L1_ST |
+ P_REL_PCIE_RX_EX_IDLE | P_GAT_PCIE_RX_EL_IDLE |
+ P_REL_GPHY_LINK_UP | P_GAT_GPHY_LINK_DOWN);
+ } else
+ sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_CLK_HALT);
+
+ /* put CPU into reset state */
+ sky2_write8(hw, B28_Y2_ASF_STAT_CMD, HCU_CCSR_ASF_RESET);
+ if (hw->chip_id == CHIP_ID_YUKON_SUPR && hw->chip_rev == CHIP_REV_YU_SU_A0)
+ /* put CPU into halt state */
+ sky2_write8(hw, B28_Y2_ASF_STAT_CMD, HCU_CCSR_ASF_HALTED);
+
+ if (pex && !(hw->flags & SKY2_HW_RAM_BUFFER)) {
+ reg = sky2_pci_read32(hw, PCI_DEV_REG1);
+ /* force to PCIe L1 */
+ reg |= PCI_FORCE_PEX_L1;
+ sky2_pci_write32(hw, PCI_DEV_REG1, reg);
+ }
+ break;
+
+ default:
+ dev_warn(&hw->pdev->dev, PFX "Invalid power state (%d) ",
+ state);
+ return;
+ }
+
+ power_control |= PCI_PM_CTRL_PME_ENABLE;
+ /* Finally, set the new power state. */
+ sky2_pci_write32(hw, hw->pm_cap + PCI_PM_CTRL, power_control);
+
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+ sky2_pci_read32(hw, B0_CTST);
+}
+
static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port)
{
u16 reg;
ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
}
- if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
- hw->chip_rev == CHIP_REV_YU_EC_U_A1) {
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_UL_2) {
/* apply fixes in PHY AFE */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 255);
gm_phy_write(hw, port, 0x18, 0xaa99);
gm_phy_write(hw, port, 0x17, 0x2011);
- /* fix for IEEE A/B Symmetry failure in 1000BASE-T */
- gm_phy_write(hw, port, 0x18, 0xa204);
- gm_phy_write(hw, port, 0x17, 0x2002);
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ /* fix for IEEE A/B Symmetry failure in 1000BASE-T */
+ gm_phy_write(hw, port, 0x18, 0xa204);
+ gm_phy_write(hw, port, 0x17, 0x2002);
+ }
/* set page register to 0 */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
/* apply workaround for integrated resistors calibration */
gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17);
gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60);
- } else if (hw->chip_id != CHIP_ID_YUKON_EX) {
+ } else if (hw->chip_id != CHIP_ID_YUKON_EX &&
+ hw->chip_id < CHIP_ID_YUKON_SUPR) {
/* no effect on Yukon-XL */
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
if (netif_msg_ifdown(sky2))
printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
- /* Stop more packets from being queued */
- netif_stop_queue(dev);
-
/* Disable port IRQ */
imask = sky2_read32(hw, B0_IMSK);
imask &= ~portirq_msk[port];
sky2_phy_power_down(hw, port);
- netif_carrier_off(dev);
-
/* turn off LED's */
sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
case CHIP_ID_YUKON_EC_U:
case CHIP_ID_YUKON_EX:
case CHIP_ID_YUKON_SUPR:
+ case CHIP_ID_YUKON_UL_2:
return 125;
case CHIP_ID_YUKON_FE:
hw->flags = SKY2_HW_GIGABIT
| SKY2_HW_NEWER_PHY
| SKY2_HW_ADV_POWER_CTL;
+
+ /* check for Rev. A1 dev 4200 */
+ if (sky2_read16(hw, Q_ADDR(Q_XA1, Q_WM)) == 0)
+ hw->flags |= SKY2_HW_CLK_POWER;
break;
case CHIP_ID_YUKON_EX:
| SKY2_HW_ADV_POWER_CTL;
break;
+ case CHIP_ID_YUKON_UL_2:
+ hw->flags = SKY2_HW_GIGABIT
+ | SKY2_HW_ADV_POWER_CTL;
+ break;
+
default:
dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n",
hw->chip_id);
if (hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P')
hw->flags |= SKY2_HW_FIBRE_PHY;
+ hw->pm_cap = pci_find_capability(hw->pdev, PCI_CAP_ID_PM);
+ if (hw->pm_cap == 0) {
+ dev_err(&hw->pdev->dev, "cannot find PowerManagement capability\n");
+ return -EIO;
+ }
hw->ports = 1;
t8 = sky2_read8(hw, B2_Y2_HW_RES);
return value & PCI_PM_CTRL_PME_ENABLE;
}
+/* This driver supports yukon2 chipset only */
+static const char *sky2_name(u8 chipid, char *buf, int sz)
+{
+ const char *name[] = {
+ "XL", /* 0xb3 */
+ "EC Ultra", /* 0xb4 */
+ "Extreme", /* 0xb5 */
+ "EC", /* 0xb6 */
+ "FE", /* 0xb7 */
+ "FE+", /* 0xb8 */
+ "Supreme", /* 0xb9 */
+ "UL 2", /* 0xba */
+ };
+
+ if (chipid >= CHIP_ID_YUKON_XL && chipid < CHIP_ID_YUKON_UL_2)
+ strncpy(buf, name[chipid - CHIP_ID_YUKON_XL], sz);
+ else
+ snprintf(buf, sz, "(chip %#x)", chipid);
+ return buf;
+}
+
static int __devinit sky2_probe(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
struct net_device *dev;
struct sky2_hw *hw;
int err, using_dac = 0, wol_default;
+ char buf1[16];
err = pci_enable_device(pdev);
if (err) {
if (err)
goto err_out_iounmap;
- dev_info(&pdev->dev, "v%s addr 0x%llx irq %d Yukon-%s (0x%x) rev %d\n",
- DRV_VERSION, (unsigned long long)pci_resource_start(pdev, 0),
- pdev->irq, yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL],
- hw->chip_id, hw->chip_rev);
+ dev_info(&pdev->dev, "v%s addr 0x%llx irq %d Yukon-2 %s rev %d\n",
+ DRV_VERSION, (unsigned long long)pci_resource_start(pdev, 0),
+ pdev->irq, sky2_name(hw->chip_id, buf1, sizeof(buf1)),
+ hw->chip_rev);
sky2_reset(hw);
pci_save_state(pdev);
pci_enable_wake(pdev, pci_choose_state(pdev, state), wol);
- pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ sky2_power_state(hw, pci_choose_state(pdev, state));
return 0;
}
if (!hw)
return 0;
- err = pci_set_power_state(pdev, PCI_D0);
- if (err)
- goto out;
+ sky2_power_state(hw, PCI_D0);
err = pci_restore_state(pdev);
if (err)
if (err) {
printk(KERN_ERR PFX "%s: could not up: %d\n",
dev->name, err);
+ rtnl_lock();
dev_close(dev);
+ rtnl_unlock();
goto out;
}
}
pci_enable_wake(pdev, PCI_D3cold, wol);
pci_disable_device(pdev);
- pci_set_power_state(pdev, PCI_D3hot);
-
+ sky2_power_state(hw, PCI_D3hot);
}
static struct pci_driver sky2_driver = {