mac_control = &sp->mac_control;
if ((mac_control->rings[ring].pkt_cnt - rxb_size) > 16) {
level = LOW;
- if ((mac_control->rings[ring].pkt_cnt - rxb_size) <
- MAX_RXDS_PER_BLOCK) {
+ if (rxb_size <= MAX_RXDS_PER_BLOCK) {
level = PANIC;
}
}
#define S2IO_TEST_LEN sizeof(s2io_gstrings) / ETH_GSTRING_LEN
#define S2IO_STRINGS_LEN S2IO_TEST_LEN * ETH_GSTRING_LEN
+#define S2IO_TIMER_CONF(timer, handle, arg, exp) \
+ init_timer(&timer); \
+ timer.function = handle; \
+ timer.data = (unsigned long) arg; \
+ mod_timer(&timer, (jiffies + exp)) \
+
/*
* Constants to be programmed into the Xena's registers, to configure
* the XAUI.
{
nic_t *nic = ring_data->nic;
struct net_device *dev = (struct net_device *) nic->dev;
- XENA_dev_config_t __iomem *bar0 = nic->bar0;
int get_block, get_offset, put_block, put_offset, ring_bufs;
rx_curr_get_info_t get_info, put_info;
RxD_t *rxdp;
#ifndef CONFIG_S2IO_NAPI
int pkt_cnt = 0;
#endif
- register u64 val64;
-
spin_lock(&nic->rx_lock);
if (atomic_read(&nic->card_state) == CARD_DOWN) {
DBG_PRINT(ERR_DBG, "%s: %s going down for reset\n",
spin_unlock(&nic->rx_lock);
}
- /*
- * rx_traffic_int reg is an R1 register, hence we read and write
- * back the same value in the register to clear it
- */
- val64 = readq(&bar0->tx_traffic_int);
- writeq(val64, &bar0->tx_traffic_int);
-
get_info = ring_data->rx_curr_get_info;
get_block = get_info.block_index;
put_info = ring_data->rx_curr_put_info;
static void tx_intr_handler(fifo_info_t *fifo_data)
{
nic_t *nic = fifo_data->nic;
- XENA_dev_config_t __iomem *bar0 = nic->bar0;
struct net_device *dev = (struct net_device *) nic->dev;
tx_curr_get_info_t get_info, put_info;
struct sk_buff *skb;
TxD_t *txdlp;
u16 j, frg_cnt;
- register u64 val64 = 0;
-
- /*
- * tx_traffic_int reg is an R1 register, hence we read and write
- * back the same value in the register to clear it
- */
- val64 = readq(&bar0->tx_traffic_int);
- writeq(val64, &bar0->tx_traffic_int);
get_info = fifo_data->tx_curr_get_info;
put_info = fifo_data->tx_curr_put_info;
setting_mac_address_failed:
free_irq(sp->pdev->irq, dev);
isr_registration_failed:
+ del_timer_sync(&sp->alarm_timer);
s2io_reset(sp);
hw_init_failed:
return err;
#endif
mac_info_t *mac_control;
struct config_param *config;
- XENA_dev_config_t __iomem *bar0 = sp->bar0;
mac_control = &sp->mac_control;
config = &sp->config;
val64 = mac_control->fifos[queue].list_info[put_off].list_phy_addr;
writeq(val64, &tx_fifo->TxDL_Pointer);
+ wmb();
+
val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST |
TX_FIFO_LAST_LIST);
#endif
writeq(val64, &tx_fifo->List_Control);
- /* Perform a PCI read to flush previous writes */
- val64 = readq(&bar0->general_int_status);
-
put_off++;
put_off %= mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1;
mac_control->fifos[queue].tx_curr_put_info.offset = put_off;
return 0;
}
+static void
+s2io_alarm_handle(unsigned long data)
+{
+ nic_t *sp = (nic_t *)data;
+
+ alarm_intr_handler(sp);
+ mod_timer(&sp->alarm_timer, jiffies + HZ / 2);
+}
+
/**
* s2io_isr - ISR handler of the device .
* @irq: the irq of the device.
nic_t *sp = dev->priv;
XENA_dev_config_t __iomem *bar0 = sp->bar0;
int i;
- u64 reason = 0;
+ u64 reason = 0, val64;
mac_info_t *mac_control;
struct config_param *config;
return IRQ_NONE;
}
- if (reason & (GEN_ERROR_INTR))
- alarm_intr_handler(sp);
-
#ifdef CONFIG_S2IO_NAPI
if (reason & GEN_INTR_RXTRAFFIC) {
if (netif_rx_schedule_prep(dev)) {
#else
/* If Intr is because of Rx Traffic */
if (reason & GEN_INTR_RXTRAFFIC) {
+ /*
+ * rx_traffic_int reg is an R1 register, writing all 1's
+ * will ensure that the actual interrupt causing bit get's
+ * cleared and hence a read can be avoided.
+ */
+ val64 = 0xFFFFFFFFFFFFFFFFULL;
+ writeq(val64, &bar0->rx_traffic_int);
for (i = 0; i < config->rx_ring_num; i++) {
rx_intr_handler(&mac_control->rings[i]);
}
/* If Intr is because of Tx Traffic */
if (reason & GEN_INTR_TXTRAFFIC) {
+ /*
+ * tx_traffic_int reg is an R1 register, writing all 1's
+ * will ensure that the actual interrupt causing bit get's
+ * cleared and hence a read can be avoided.
+ */
+ val64 = 0xFFFFFFFFFFFFFFFFULL;
+ writeq(val64, &bar0->tx_traffic_int);
+
for (i = 0; i < config->tx_fifo_num; i++)
tx_intr_handler(&mac_control->fifos[i]);
}
int s2io_change_mtu(struct net_device *dev, int new_mtu)
{
nic_t *sp = dev->priv;
- XENA_dev_config_t __iomem *bar0 = sp->bar0;
- register u64 val64;
-
- if (netif_running(dev)) {
- DBG_PRINT(ERR_DBG, "%s: Must be stopped to ", dev->name);
- DBG_PRINT(ERR_DBG, "change its MTU\n");
- return -EBUSY;
- }
if ((new_mtu < MIN_MTU) || (new_mtu > S2IO_JUMBO_SIZE)) {
DBG_PRINT(ERR_DBG, "%s: MTU size is invalid.\n",
return -EPERM;
}
- /* Set the new MTU into the PYLD register of the NIC */
- val64 = new_mtu;
- writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
-
dev->mtu = new_mtu;
+ if (netif_running(dev)) {
+ s2io_card_down(sp);
+ netif_stop_queue(dev);
+ if (s2io_card_up(sp)) {
+ DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
+ __FUNCTION__);
+ }
+ if (netif_queue_stopped(dev))
+ netif_wake_queue(dev);
+ } else { /* Device is down */
+ XENA_dev_config_t __iomem *bar0 = sp->bar0;
+ u64 val64 = new_mtu;
+
+ writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
+ }
return 0;
}
unsigned long flags;
register u64 val64 = 0;
+ del_timer_sync(&sp->alarm_timer);
/* If s2io_set_link task is executing, wait till it completes. */
while (test_and_set_bit(0, &(sp->link_state))) {
msleep(50);
return -ENODEV;
}
+ S2IO_TIMER_CONF(sp->alarm_timer, s2io_alarm_handle, sp, (HZ/2));
+
atomic_set(&sp->card_state, CARD_UP);
return 0;
}
projects / linux-2.6 / blobdiff