/* S2io Driver name & version. */
static char s2io_driver_name[] = "Neterion";
-static char s2io_driver_version[] = "Version 1.7.7";
+static char s2io_driver_version[] = "Version 2.0.3.1";
static inline int RXD_IS_UP2DT(RxD_t *rxdp)
{
static u64 herc_act_dtx_cfg[] = {
/* Set address */
- 0x80000515BA750000ULL, 0x80000515BA7500E0ULL,
+ 0x8000051536750000ULL, 0x80000515367500E0ULL,
/* Write data */
- 0x80000515BA750004ULL, 0x80000515BA7500E4ULL,
+ 0x8000051536750004ULL, 0x80000515367500E4ULL,
/* Set address */
0x80010515003F0000ULL, 0x80010515003F00E0ULL,
/* Write data */
0x80010515003F0004ULL, 0x80010515003F00E4ULL,
/* Set address */
+ 0x801205150D440000ULL, 0x801205150D4400E0ULL,
+ /* Write data */
+ 0x801205150D440004ULL, 0x801205150D4400E4ULL,
+ /* Set address */
0x80020515F2100000ULL, 0x80020515F21000E0ULL,
/* Write data */
0x80020515F2100004ULL, 0x80020515F21000E4ULL,
#ifndef CONFIG_S2IO_NAPI
static unsigned int indicate_max_pkts;
#endif
+/* Frequency of Rx desc syncs expressed as power of 2 */
+static unsigned int rxsync_frequency = 3;
/*
* S2IO device table.
size += config->tx_cfg[i].fifo_len;
}
if (size > MAX_AVAILABLE_TXDS) {
- DBG_PRINT(ERR_DBG, "%s: Total number of Tx FIFOs ",
- dev->name);
- DBG_PRINT(ERR_DBG, "exceeds the maximum value ");
- DBG_PRINT(ERR_DBG, "that can be used\n");
+ DBG_PRINT(ERR_DBG, "%s: Requested TxDs too high, ",
+ __FUNCTION__);
+ DBG_PRINT(ERR_DBG, "Requested: %d, max supported: 8192\n", size);
return FAILURE;
}
lst_per_page);
for (j = 0; j < page_num; j++) {
int mem_blks = (j * lst_per_page);
- if (!mac_control->fifos[i].list_info[mem_blks].
- list_virt_addr)
+ if ((!mac_control->fifos[i].list_info) ||
+ (!mac_control->fifos[i].list_info[mem_blks].
+ list_virt_addr))
break;
pci_free_consistent(nic->pdev, PAGE_SIZE,
mac_control->fifos[i].
static int s2io_verify_pci_mode(nic_t *nic)
{
- XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0;
+ XENA_dev_config_t __iomem *bar0 = nic->bar0;
register u64 val64 = 0;
int mode;
*/
static int s2io_print_pci_mode(nic_t *nic)
{
- XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0;
+ XENA_dev_config_t __iomem *bar0 = nic->bar0;
register u64 val64 = 0;
int mode;
struct config_param *config = &nic->config;
*/
if (nic->device_type & XFRAME_II_DEVICE) {
while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) {
- SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
+ SPECIAL_REG_WRITE(herc_act_dtx_cfg[dtx_cnt],
&bar0->dtx_control, UF);
if (dtx_cnt & 0x1)
msleep(1); /* Necessary!! */
writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q4q7);
/* Disable RMAC PAD STRIPPING */
- add = (void *) &bar0->mac_cfg;
+ add = &bar0->mac_cfg;
val64 = readq(&bar0->mac_cfg);
val64 &= ~(MAC_CFG_RMAC_STRIP_PAD);
writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
writeq(val64, &bar0->wreq_split_mask);
}
+ /* Setting Link stability period to 64 ms */
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ val64 = MISC_LINK_STABILITY_PRD(3);
+ writeq(val64, &bar0->misc_control);
+ }
+
return SUCCESS;
}
+#define LINK_UP_DOWN_INTERRUPT 1
+#define MAC_RMAC_ERR_TIMER 2
+
+#if defined(CONFIG_MSI_MODE) || defined(CONFIG_MSIX_MODE)
+#define s2io_link_fault_indication(x) MAC_RMAC_ERR_TIMER
+#else
+int s2io_link_fault_indication(nic_t *nic)
+{
+ if (nic->device_type == XFRAME_II_DEVICE)
+ return LINK_UP_DOWN_INTERRUPT;
+ else
+ return MAC_RMAC_ERR_TIMER;
+}
+#endif
/**
* en_dis_able_nic_intrs - Enable or Disable the interrupts
temp64 &= ~((u64) val64);
writeq(temp64, &bar0->general_int_mask);
/*
- * Disabled all PCIX, Flash, MDIO, IIC and GPIO
+ * If Hercules adapter enable GPIO otherwise
+ * disabled all PCIX, Flash, MDIO, IIC and GPIO
* interrupts for now.
* TODO
*/
- writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
+ if (s2io_link_fault_indication(nic) ==
+ LINK_UP_DOWN_INTERRUPT ) {
+ temp64 = readq(&bar0->pic_int_mask);
+ temp64 &= ~((u64) PIC_INT_GPIO);
+ writeq(temp64, &bar0->pic_int_mask);
+ temp64 = readq(&bar0->gpio_int_mask);
+ temp64 &= ~((u64) GPIO_INT_MASK_LINK_UP);
+ writeq(temp64, &bar0->gpio_int_mask);
+ } else {
+ writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
+ }
/*
* No MSI Support is available presently, so TTI and
* RTI interrupts are also disabled.
writeq(temp64, &bar0->general_int_mask);
/*
* All MAC block error interrupts are disabled for now
- * except the link status change interrupt.
* TODO
*/
- val64 = MAC_INT_STATUS_RMAC_INT;
- temp64 = readq(&bar0->mac_int_mask);
- temp64 &= ~((u64) val64);
- writeq(temp64, &bar0->mac_int_mask);
-
- val64 = readq(&bar0->mac_rmac_err_mask);
- val64 &= ~((u64) RMAC_LINK_STATE_CHANGE_INT);
- writeq(val64, &bar0->mac_rmac_err_mask);
} else if (flag == DISABLE_INTRS) {
/*
* Disable MAC Intrs in the general intr mask register
}
/* Enable select interrupts */
- interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | TX_MAC_INTR |
- RX_MAC_INTR | MC_INTR;
+ interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
+ interruptible |= TX_PIC_INTR | RX_PIC_INTR;
+ interruptible |= TX_MAC_INTR | RX_MAC_INTR;
+
en_dis_able_nic_intrs(nic, interruptible, ENABLE_INTRS);
/*
val64 |= 0x0000800000000000ULL;
writeq(val64, &bar0->gpio_control);
val64 = 0x0411040400000000ULL;
- writeq(val64, (void __iomem *) ((u8 *) bar0 + 0x2700));
+ writeq(val64, (void __iomem *)bar0 + 0x2700);
}
/*
config = &nic->config;
/* Disable all interrupts */
- interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | TX_MAC_INTR |
- RX_MAC_INTR | MC_INTR;
+ interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
+ interruptible |= TX_PIC_INTR | RX_PIC_INTR;
+ interruptible |= TX_MAC_INTR | RX_MAC_INTR;
en_dis_able_nic_intrs(nic, interruptible, DISABLE_INTRS);
/* Disable PRCs */
#ifndef CONFIG_S2IO_NAPI
unsigned long flags;
#endif
+ RxD_t *first_rxdp = NULL;
mac_control = &nic->mac_control;
config = &nic->config;
if (!skb) {
DBG_PRINT(ERR_DBG, "%s: Out of ", dev->name);
DBG_PRINT(ERR_DBG, "memory to allocate SKBs\n");
+ if (first_rxdp) {
+ wmb();
+ first_rxdp->Control_1 |= RXD_OWN_XENA;
+ }
return -ENOMEM;
}
#ifndef CONFIG_2BUFF_MODE
rxdp->Control_2 &= (~MASK_BUFFER0_SIZE);
rxdp->Control_2 |= SET_BUFFER0_SIZE(size);
rxdp->Host_Control = (unsigned long) (skb);
- rxdp->Control_1 |= RXD_OWN_XENA;
+ if (alloc_tab & ((1 << rxsync_frequency) - 1))
+ rxdp->Control_1 |= RXD_OWN_XENA;
off++;
off %= (MAX_RXDS_PER_BLOCK + 1);
mac_control->rings[ring_no].rx_curr_put_info.offset = off;
rxdp->Control_2 |= SET_BUFFER1_SIZE(1); /* dummy. */
rxdp->Control_2 |= BIT(0); /* Set Buffer_Empty bit. */
rxdp->Host_Control = (u64) ((unsigned long) (skb));
- rxdp->Control_1 |= RXD_OWN_XENA;
+ if (alloc_tab & ((1 << rxsync_frequency) - 1))
+ rxdp->Control_1 |= RXD_OWN_XENA;
off++;
mac_control->rings[ring_no].rx_curr_put_info.offset = off;
#endif
rxdp->Control_2 |= SET_RXD_MARKER;
+ if (!(alloc_tab & ((1 << rxsync_frequency) - 1))) {
+ if (first_rxdp) {
+ wmb();
+ first_rxdp->Control_1 |= RXD_OWN_XENA;
+ }
+ first_rxdp = rxdp;
+ }
atomic_inc(&nic->rx_bufs_left[ring_no]);
alloc_tab++;
}
end:
+ /* Transfer ownership of first descriptor to adapter just before
+ * exiting. Before that, use memory barrier so that ownership
+ * and other fields are seen by adapter correctly.
+ */
+ if (first_rxdp) {
+ wmb();
+ first_rxdp->Control_1 |= RXD_OWN_XENA;
+ }
+
return SUCCESS;
}
int pkt_cnt = 0, org_pkts_to_process;
mac_info_t *mac_control;
struct config_param *config;
- XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0;
+ XENA_dev_config_t __iomem *bar0 = nic->bar0;
u64 val64;
int i;
for (j = 0; j < frg_cnt; j++, txdlp++) {
skb_frag_t *frag =
&skb_shinfo(skb)->frags[j];
+ if (!txdlp->Buffer_Pointer)
+ break;
pci_unmap_page(nic->pdev,
(dma_addr_t)
txdlp->
register u64 val64 = 0, err_reg = 0;
/* Handling link status change error Intr */
- err_reg = readq(&bar0->mac_rmac_err_reg);
- writeq(err_reg, &bar0->mac_rmac_err_reg);
- if (err_reg & RMAC_LINK_STATE_CHANGE_INT) {
- schedule_work(&nic->set_link_task);
+ if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
+ err_reg = readq(&bar0->mac_rmac_err_reg);
+ writeq(err_reg, &bar0->mac_rmac_err_reg);
+ if (err_reg & RMAC_LINK_STATE_CHANGE_INT) {
+ schedule_work(&nic->set_link_task);
+ }
}
/* Handling Ecc errors */
DBG_PRINT(ERR_DBG, "%s: Device indicates ",
dev->name);
DBG_PRINT(ERR_DBG, "double ECC error!!\n");
- netif_stop_queue(dev);
- schedule_work(&nic->rst_timer_task);
+ if (nic->device_type != XFRAME_II_DEVICE) {
+ netif_stop_queue(dev);
+ schedule_work(&nic->rst_timer_task);
+ }
} else {
nic->mac_control.stats_info->sw_stat.
single_ecc_errs++;
u64 val64;
u16 subid, pci_cmd;
+ /* Back up the PCI-X CMD reg, dont want to lose MMRBC, OST settings */
+ pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd));
+
val64 = SW_RESET_ALL;
writeq(val64, &bar0->sw_reset);
*/
msleep(250);
- if (!(sp->device_type & XFRAME_II_DEVICE)) {
- /* Restore the PCI state saved during initializarion. */
- pci_restore_state(sp->pdev);
- } else {
- pci_set_master(sp->pdev);
- }
+ /* Restore the PCI state saved during initialization. */
+ pci_restore_state(sp->pdev);
+ pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
+ pci_cmd);
s2io_init_pci(sp);
msleep(250);
s2io_set_swapper(sp);
/* Clear certain PCI/PCI-X fields after reset */
- pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
- pci_cmd &= 0x7FFF; /* Clear parity err detect bit */
- pci_write_config_word(sp->pdev, PCI_COMMAND, pci_cmd);
+ if (sp->device_type == XFRAME_II_DEVICE) {
+ /* Clear parity err detect bit */
+ pci_write_config_word(sp->pdev, PCI_STATUS, 0x8000);
- val64 = readq(&bar0->txpic_int_reg);
- val64 &= ~BIT(62); /* Clearing PCI_STATUS error reflected here */
- writeq(val64, &bar0->txpic_int_reg);
+ /* Clearing PCIX Ecc status register */
+ pci_write_config_dword(sp->pdev, 0x68, 0x7C);
- /* Clearing PCIX Ecc status register */
- pci_write_config_dword(sp->pdev, 0x68, 0);
+ /* Clearing PCI_STATUS error reflected here */
+ writeq(BIT(62), &bar0->txpic_int_reg);
+ }
/* Reset device statistics maintained by OS */
memset(&sp->stats, 0, sizeof (struct net_device_stats));
val64 |= 0x0000800000000000ULL;
writeq(val64, &bar0->gpio_control);
val64 = 0x0411040400000000ULL;
- writeq(val64, (void __iomem *) ((u8 *) bar0 + 0x2700));
+ writeq(val64, (void __iomem *)bar0 + 0x2700);
}
/*
* Nic is initialized
*/
netif_carrier_off(dev);
- sp->last_link_state = 0; /* Unkown link state */
+ sp->last_link_state = 0;
/* Initialize H/W and enable interrupts */
if (s2io_card_up(sp)) {
spin_unlock_irqrestore(&sp->tx_lock, flags);
return 0;
}
+
+ /* A buffer with no data will be dropped */
+ if (!skb->len) {
+ DBG_PRINT(TX_DBG, "%s:Buffer has no data..\n", dev->name);
+ dev_kfree_skb(skb);
+ spin_unlock_irqrestore(&sp->tx_lock, flags);
+ return 0;
+ }
+
#ifdef NETIF_F_TSO
mss = skb_shinfo(skb)->tso_size;
if (mss) {
/* For fragmented SKB. */
for (i = 0; i < frg_cnt; i++) {
skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+ /* A '0' length fragment will be ignored */
+ if (!frag->size)
+ continue;
txdp++;
txdp->Buffer_Pointer = (u64) pci_map_page
(sp->pdev, frag->page, frag->page_offset,
val64 = mac_control->fifos[queue].list_info[put_off].list_phy_addr;
writeq(val64, &tx_fifo->TxDL_Pointer);
- wmb();
-
val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST |
TX_FIFO_LAST_LIST);
#endif
writeq(val64, &tx_fifo->List_Control);
+ mmiowb();
+
put_off++;
put_off %= mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1;
mac_control->fifos[queue].tx_curr_put_info.offset = put_off;
mod_timer(&sp->alarm_timer, jiffies + HZ / 2);
}
+static void s2io_txpic_intr_handle(nic_t *sp)
+{
+ XENA_dev_config_t __iomem *bar0 = sp->bar0;
+ u64 val64;
+
+ val64 = readq(&bar0->pic_int_status);
+ if (val64 & PIC_INT_GPIO) {
+ val64 = readq(&bar0->gpio_int_reg);
+ if ((val64 & GPIO_INT_REG_LINK_DOWN) &&
+ (val64 & GPIO_INT_REG_LINK_UP)) {
+ val64 |= GPIO_INT_REG_LINK_DOWN;
+ val64 |= GPIO_INT_REG_LINK_UP;
+ writeq(val64, &bar0->gpio_int_reg);
+ goto masking;
+ }
+
+ if (((sp->last_link_state == LINK_UP) &&
+ (val64 & GPIO_INT_REG_LINK_DOWN)) ||
+ ((sp->last_link_state == LINK_DOWN) &&
+ (val64 & GPIO_INT_REG_LINK_UP))) {
+ val64 = readq(&bar0->gpio_int_mask);
+ val64 |= GPIO_INT_MASK_LINK_DOWN;
+ val64 |= GPIO_INT_MASK_LINK_UP;
+ writeq(val64, &bar0->gpio_int_mask);
+ s2io_set_link((unsigned long)sp);
+ }
+masking:
+ if (sp->last_link_state == LINK_UP) {
+ /*enable down interrupt */
+ val64 = readq(&bar0->gpio_int_mask);
+ /* unmasks link down intr */
+ val64 &= ~GPIO_INT_MASK_LINK_DOWN;
+ /* masks link up intr */
+ val64 |= GPIO_INT_MASK_LINK_UP;
+ writeq(val64, &bar0->gpio_int_mask);
+ } else {
+ /*enable UP Interrupt */
+ val64 = readq(&bar0->gpio_int_mask);
+ /* unmasks link up interrupt */
+ val64 &= ~GPIO_INT_MASK_LINK_UP;
+ /* masks link down interrupt */
+ val64 |= GPIO_INT_MASK_LINK_DOWN;
+ writeq(val64, &bar0->gpio_int_mask);
+ }
+ }
+}
+
/**
* s2io_isr - ISR handler of the device .
* @irq: the irq of the device.
tx_intr_handler(&mac_control->fifos[i]);
}
+ if (reason & GEN_INTR_TXPIC)
+ s2io_txpic_intr_handle(sp);
/*
* If the Rx buffer count is below the panic threshold then
* reallocate the buffers from the interrupt handler itself,
}
subid = nic->pdev->subsystem_device;
- /*
- * Allow a small delay for the NICs self initiated
- * cleanup to complete.
- */
- msleep(100);
+ if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
+ /*
+ * Allow a small delay for the NICs self initiated
+ * cleanup to complete.
+ */
+ msleep(100);
+ }
val64 = readq(&bar0->adapter_status);
if (verify_xena_quiescence(nic, val64, nic->device_enabled_once)) {
val64 |= ADAPTER_LED_ON;
writeq(val64, &bar0->adapter_control);
}
- val64 = readq(&bar0->adapter_status);
- if (!LINK_IS_UP(val64)) {
- DBG_PRINT(ERR_DBG, "%s:", dev->name);
- DBG_PRINT(ERR_DBG, " Link down");
- DBG_PRINT(ERR_DBG, "after ");
- DBG_PRINT(ERR_DBG, "enabling ");
- DBG_PRINT(ERR_DBG, "device \n");
+ if (s2io_link_fault_indication(nic) ==
+ MAC_RMAC_ERR_TIMER) {
+ val64 = readq(&bar0->adapter_status);
+ if (!LINK_IS_UP(val64)) {
+ DBG_PRINT(ERR_DBG, "%s:", dev->name);
+ DBG_PRINT(ERR_DBG, " Link down");
+ DBG_PRINT(ERR_DBG, "after ");
+ DBG_PRINT(ERR_DBG, "enabling ");
+ DBG_PRINT(ERR_DBG, "device \n");
+ }
}
if (nic->device_enabled_once == FALSE) {
nic->device_enabled_once = TRUE;
#ifndef CONFIG_S2IO_NAPI
module_param(indicate_max_pkts, int, 0);
#endif
+module_param(rxsync_frequency, int, 0);
/**
* s2io_init_nic - Initialization of the adapter .
config = &sp->config;
/* Tx side parameters. */
- tx_fifo_len[0] = DEFAULT_FIFO_LEN; /* Default value. */
+ if (tx_fifo_len[0] == 0)
+ tx_fifo_len[0] = DEFAULT_FIFO_LEN; /* Default value. */
config->tx_fifo_num = tx_fifo_num;
for (i = 0; i < MAX_TX_FIFOS; i++) {
config->tx_cfg[i].fifo_len = tx_fifo_len[i];
config->max_txds = MAX_SKB_FRAGS;
/* Rx side parameters. */
- rx_ring_sz[0] = SMALL_BLK_CNT; /* Default value. */
+ if (rx_ring_sz[0] == 0)
+ rx_ring_sz[0] = SMALL_BLK_CNT; /* Default value. */
config->rx_ring_num = rx_ring_num;
for (i = 0; i < MAX_RX_RINGS; i++) {
config->rx_cfg[i].num_rxd = rx_ring_sz[i] *
/* initialize the shared memory used by the NIC and the host */
if (init_shared_mem(sp)) {
DBG_PRINT(ERR_DBG, "%s: Memory allocation failed\n",
- dev->name);
+ __FUNCTION__);
ret = -ENOMEM;
goto mem_alloc_failed;
}
INIT_WORK(&sp->set_link_task,
(void (*)(void *)) s2io_set_link, sp);
- if (!(sp->device_type & XFRAME_II_DEVICE)) {
- pci_save_state(sp->pdev);
- }
+ pci_save_state(sp->pdev);
/* Setting swapper control on the NIC, for proper reset operation */
if (s2io_set_swapper(sp)) {
sp->def_mac_addr[0].mac_addr[3],
sp->def_mac_addr[0].mac_addr[4],
sp->def_mac_addr[0].mac_addr[5]);
- int mode = s2io_print_pci_mode(sp);
+ mode = s2io_print_pci_mode(sp);
if (mode < 0) {
DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode ");
ret = -EBADSLT;
projects / linux-2.6 / blobdiff