* aggregation happens until we hit max IP pkt size(64K)
*/
S2IO_PARM_INT(lro_max_pkts, 0xFFFF);
-#ifndef CONFIG_S2IO_NAPI
S2IO_PARM_INT(indicate_max_pkts, 0);
-#endif
+
+S2IO_PARM_INT(napi, 1);
+S2IO_PARM_INT(ufo, 0);
static unsigned int tx_fifo_len[MAX_TX_FIFOS] =
{DEFAULT_FIFO_0_LEN, [1 ...(MAX_TX_FIFOS - 1)] = DEFAULT_FIFO_1_7_LEN};
}
}
- nic->ufo_in_band_v = kmalloc((sizeof(u64) * size), GFP_KERNEL);
+ nic->ufo_in_band_v = kcalloc(size, sizeof(u64), GFP_KERNEL);
if (!nic->ufo_in_band_v)
return -ENOMEM;
- memset(nic->ufo_in_band_v, 0, size);
/* Allocation and initialization of RXDs in Rings */
size = 0;
val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) |
TTI_DATA2_MEM_TX_UFC_B(0x20) |
- TTI_DATA2_MEM_TX_UFC_C(0x70) | TTI_DATA2_MEM_TX_UFC_D(0x80);
+ TTI_DATA2_MEM_TX_UFC_C(0x40) | TTI_DATA2_MEM_TX_UFC_D(0x80);
writeq(val64, &bar0->tti_data2_mem);
val64 = TTI_CMD_MEM_WE | TTI_CMD_MEM_STROBE_NEW_CMD;
* that does not start on an ADB to reduce disconnects.
*/
if (nic->device_type == XFRAME_II_DEVICE) {
- val64 = EXT_REQ_EN | MISC_LINK_STABILITY_PRD(3);
+ val64 = FAULT_BEHAVIOUR | EXT_REQ_EN |
+ MISC_LINK_STABILITY_PRD(3);
writeq(val64, &bar0->misc_control);
val64 = readq(&bar0->pic_control2);
val64 &= ~(BIT(13)|BIT(14)|BIT(15));
}
}
-static int check_prc_pcc_state(u64 val64, int flag, int rev_id, int herc)
+/**
+ * verify_pcc_quiescent- Checks for PCC quiescent state
+ * Return: 1 If PCC is quiescence
+ * 0 If PCC is not quiescence
+ */
+static int verify_pcc_quiescent(nic_t *sp, int flag)
{
- int ret = 0;
+ int ret = 0, herc;
+ XENA_dev_config_t __iomem *bar0 = sp->bar0;
+ u64 val64 = readq(&bar0->adapter_status);
+
+ herc = (sp->device_type == XFRAME_II_DEVICE);
if (flag == FALSE) {
- if ((!herc && (rev_id >= 4)) || herc) {
- if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) &&
- ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
- ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
+ if ((!herc && (get_xena_rev_id(sp->pdev) >= 4)) || herc) {
+ if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE))
ret = 1;
- }
- }else {
- if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) &&
- ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
- ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
+ } else {
+ if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
ret = 1;
- }
}
} else {
- if ((!herc && (rev_id >= 4)) || herc) {
+ if ((!herc && (get_xena_rev_id(sp->pdev) >= 4)) || herc) {
if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) ==
- ADAPTER_STATUS_RMAC_PCC_IDLE) &&
- (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ||
- ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
- ADAPTER_STATUS_RC_PRC_QUIESCENT))) {
+ ADAPTER_STATUS_RMAC_PCC_IDLE))
ret = 1;
- }
} else {
if (((val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) ==
- ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) &&
- (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ||
- ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
- ADAPTER_STATUS_RC_PRC_QUIESCENT))) {
+ ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
ret = 1;
- }
}
}
}
/**
* verify_xena_quiescence - Checks whether the H/W is ready
- * @val64 : Value read from adapter status register.
- * @flag : indicates if the adapter enable bit was ever written once
- * before.
* Description: Returns whether the H/W is ready to go or not. Depending
* on whether adapter enable bit was written or not the comparison
* differs and the calling function passes the input argument flag to
* 0 If Xena is not quiescence
*/
-static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag)
+static int verify_xena_quiescence(nic_t *sp)
{
- int ret = 0, herc;
- u64 tmp64 = ~((u64) val64);
- int rev_id = get_xena_rev_id(sp->pdev);
+ int mode;
+ XENA_dev_config_t __iomem *bar0 = sp->bar0;
+ u64 val64 = readq(&bar0->adapter_status);
+ mode = s2io_verify_pci_mode(sp);
- herc = (sp->device_type == XFRAME_II_DEVICE);
- if (!
- (tmp64 &
- (ADAPTER_STATUS_TDMA_READY | ADAPTER_STATUS_RDMA_READY |
- ADAPTER_STATUS_PFC_READY | ADAPTER_STATUS_TMAC_BUF_EMPTY |
- ADAPTER_STATUS_PIC_QUIESCENT | ADAPTER_STATUS_MC_DRAM_READY |
- ADAPTER_STATUS_MC_QUEUES_READY | ADAPTER_STATUS_M_PLL_LOCK |
- ADAPTER_STATUS_P_PLL_LOCK))) {
- ret = check_prc_pcc_state(val64, flag, rev_id, herc);
+ if (!(val64 & ADAPTER_STATUS_TDMA_READY)) {
+ DBG_PRINT(ERR_DBG, "%s", "TDMA is not ready!");
+ return 0;
+ }
+ if (!(val64 & ADAPTER_STATUS_RDMA_READY)) {
+ DBG_PRINT(ERR_DBG, "%s", "RDMA is not ready!");
+ return 0;
+ }
+ if (!(val64 & ADAPTER_STATUS_PFC_READY)) {
+ DBG_PRINT(ERR_DBG, "%s", "PFC is not ready!");
+ return 0;
+ }
+ if (!(val64 & ADAPTER_STATUS_TMAC_BUF_EMPTY)) {
+ DBG_PRINT(ERR_DBG, "%s", "TMAC BUF is not empty!");
+ return 0;
+ }
+ if (!(val64 & ADAPTER_STATUS_PIC_QUIESCENT)) {
+ DBG_PRINT(ERR_DBG, "%s", "PIC is not QUIESCENT!");
+ return 0;
+ }
+ if (!(val64 & ADAPTER_STATUS_MC_DRAM_READY)) {
+ DBG_PRINT(ERR_DBG, "%s", "MC_DRAM is not ready!");
+ return 0;
+ }
+ if (!(val64 & ADAPTER_STATUS_MC_QUEUES_READY)) {
+ DBG_PRINT(ERR_DBG, "%s", "MC_QUEUES is not ready!");
+ return 0;
+ }
+ if (!(val64 & ADAPTER_STATUS_M_PLL_LOCK)) {
+ DBG_PRINT(ERR_DBG, "%s", "M_PLL is not locked!");
+ return 0;
}
- return ret;
+ /*
+ * In PCI 33 mode, the P_PLL is not used, and therefore,
+ * the the P_PLL_LOCK bit in the adapter_status register will
+ * not be asserted.
+ */
+ if (!(val64 & ADAPTER_STATUS_P_PLL_LOCK) &&
+ sp->device_type == XFRAME_II_DEVICE && mode !=
+ PCI_MODE_PCI_33) {
+ DBG_PRINT(ERR_DBG, "%s", "P_PLL is not locked!");
+ return 0;
+ }
+ if (!((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
+ ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
+ DBG_PRINT(ERR_DBG, "%s", "RC_PRC is not QUIESCENT!");
+ return 0;
+ }
+ return 1;
}
/**
* it.
*/
val64 = readq(&bar0->adapter_status);
- if (!verify_xena_quiescence(nic, val64, nic->device_enabled_once)) {
+ if (!verify_xena_quiescence(nic)) {
DBG_PRINT(ERR_DBG, "%s: device is not ready, ", dev->name);
DBG_PRINT(ERR_DBG, "Adapter status reads: 0x%llx\n",
(unsigned long long) val64);
struct config_param *config;
u64 tmp;
buffAdd_t *ba;
-#ifndef CONFIG_S2IO_NAPI
unsigned long flags;
-#endif
RxD_t *first_rxdp = NULL;
mac_control = &nic->mac_control;
DBG_PRINT(INTR_DBG, "%s: Next block at: %p\n",
dev->name, rxdp);
}
-#ifndef CONFIG_S2IO_NAPI
- spin_lock_irqsave(&nic->put_lock, flags);
- mac_control->rings[ring_no].put_pos =
- (block_no * (rxd_count[nic->rxd_mode] + 1)) + off;
- spin_unlock_irqrestore(&nic->put_lock, flags);
-#endif
+ if(!napi) {
+ spin_lock_irqsave(&nic->put_lock, flags);
+ mac_control->rings[ring_no].put_pos =
+ (block_no * (rxd_count[nic->rxd_mode] + 1)) + off;
+ spin_unlock_irqrestore(&nic->put_lock, flags);
+ } else {
+ mac_control->rings[ring_no].put_pos =
+ (block_no * (rxd_count[nic->rxd_mode] + 1)) + off;
+ }
if ((rxdp->Control_1 & RXD_OWN_XENA) &&
((nic->rxd_mode >= RXD_MODE_3A) &&
(rxdp->Control_2 & BIT(0)))) {
* 0 on success and 1 if there are No Rx packets to be processed.
*/
-#if defined(CONFIG_S2IO_NAPI)
static int s2io_poll(struct net_device *dev, int *budget)
{
nic_t *nic = dev->priv;
mac_info_t *mac_control;
struct config_param *config;
XENA_dev_config_t __iomem *bar0 = nic->bar0;
- u64 val64 = 0xFFFFFFFFFFFFFFFFULL;
int i;
atomic_inc(&nic->isr_cnt);
nic->pkts_to_process = dev->quota;
org_pkts_to_process = nic->pkts_to_process;
- writeq(val64, &bar0->rx_traffic_int);
- val64 = readl(&bar0->rx_traffic_int);
+ writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
+ readl(&bar0->rx_traffic_int);
for (i = 0; i < config->rx_ring_num; i++) {
rx_intr_handler(&mac_control->rings[i]);
}
/* Re enable the Rx interrupts. */
writeq(0x0, &bar0->rx_traffic_mask);
- val64 = readl(&bar0->rx_traffic_mask);
+ readl(&bar0->rx_traffic_mask);
atomic_dec(&nic->isr_cnt);
return 0;
atomic_dec(&nic->isr_cnt);
return 1;
}
-#endif
#ifdef CONFIG_NET_POLL_CONTROLLER
/**
rx_curr_get_info_t get_info, put_info;
RxD_t *rxdp;
struct sk_buff *skb;
-#ifndef CONFIG_S2IO_NAPI
int pkt_cnt = 0;
-#endif
int i;
spin_lock(&nic->rx_lock);
put_info = ring_data->rx_curr_put_info;
put_block = put_info.block_index;
rxdp = ring_data->rx_blocks[get_block].rxds[get_info.offset].virt_addr;
-#ifndef CONFIG_S2IO_NAPI
- spin_lock(&nic->put_lock);
- put_offset = ring_data->put_pos;
- spin_unlock(&nic->put_lock);
-#else
- put_offset = (put_block * (rxd_count[nic->rxd_mode] + 1)) +
- put_info.offset;
-#endif
+ if (!napi) {
+ spin_lock(&nic->put_lock);
+ put_offset = ring_data->put_pos;
+ spin_unlock(&nic->put_lock);
+ } else
+ put_offset = ring_data->put_pos;
+
while (RXD_IS_UP2DT(rxdp)) {
- /* If your are next to put index then it's FIFO full condition */
+ /*
+ * If your are next to put index then it's
+ * FIFO full condition
+ */
if ((get_block == put_block) &&
(get_info.offset + 1) == put_info.offset) {
DBG_PRINT(INTR_DBG, "%s: Ring Full\n",dev->name);
rxdp = ring_data->rx_blocks[get_block].block_virt_addr;
}
-#ifdef CONFIG_S2IO_NAPI
nic->pkts_to_process -= 1;
- if (!nic->pkts_to_process)
+ if ((napi) && (!nic->pkts_to_process))
break;
-#else
pkt_cnt++;
if ((indicate_max_pkts) && (pkt_cnt > indicate_max_pkts))
break;
-#endif
}
if (nic->lro) {
/* Clear all LRO sessions before exiting */
}
if ((err >> 48) == 0xA) {
DBG_PRINT(TX_DBG, "TxD returned due \
-to loss of link\n");
+ to loss of link\n");
}
else {
- DBG_PRINT(ERR_DBG, "***TxD error \
-%llx\n", err);
+ DBG_PRINT(ERR_DBG, "***TxD error %llx\n", err);
}
}
}
return ret;
}
+/*
+ * check_pci_device_id - Checks if the device id is supported
+ * @id : device id
+ * Description: Function to check if the pci device id is supported by driver.
+ * Return value: Actual device id if supported else PCI_ANY_ID
+ */
+static u16 check_pci_device_id(u16 id)
+{
+ switch (id) {
+ case PCI_DEVICE_ID_HERC_WIN:
+ case PCI_DEVICE_ID_HERC_UNI:
+ return XFRAME_II_DEVICE;
+ case PCI_DEVICE_ID_S2IO_UNI:
+ case PCI_DEVICE_ID_S2IO_WIN:
+ return XFRAME_I_DEVICE;
+ default:
+ return PCI_ANY_ID;
+ }
+}
/**
* s2io_reset - Resets the card.
XENA_dev_config_t __iomem *bar0 = sp->bar0;
u64 val64;
u16 subid, pci_cmd;
+ int i;
+ u16 val16;
+ DBG_PRINT(INIT_DBG,"%s - Resetting XFrame card %s\n",
+ __FUNCTION__, sp->dev->name);
/* Back up the PCI-X CMD reg, dont want to lose MMRBC, OST settings */
pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd));
+ if (sp->device_type == XFRAME_II_DEVICE) {
+ int ret;
+ ret = pci_set_power_state(sp->pdev, 3);
+ if (!ret)
+ ret = pci_set_power_state(sp->pdev, 0);
+ else {
+ DBG_PRINT(ERR_DBG,"%s PME based SW_Reset failed!\n",
+ __FUNCTION__);
+ goto old_way;
+ }
+ msleep(20);
+ goto new_way;
+ }
+old_way:
val64 = SW_RESET_ALL;
writeq(val64, &bar0->sw_reset);
-
- /*
- * At this stage, if the PCI write is indeed completed, the
- * card is reset and so is the PCI Config space of the device.
- * So a read cannot be issued at this stage on any of the
- * registers to ensure the write into "sw_reset" register
- * has gone through.
- * Question: Is there any system call that will explicitly force
- * all the write commands still pending on the bus to be pushed
- * through?
- * As of now I'am just giving a 250ms delay and hoping that the
- * PCI write to sw_reset register is done by this time.
- */
- msleep(250);
+new_way:
if (strstr(sp->product_name, "CX4")) {
msleep(750);
}
+ msleep(250);
+ for (i = 0; i < S2IO_MAX_PCI_CONFIG_SPACE_REINIT; i++) {
- /* Restore the PCI state saved during initialization. */
- pci_restore_state(sp->pdev);
- pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
- pci_cmd);
- s2io_init_pci(sp);
+ /* Restore the PCI state saved during initialization. */
+ pci_restore_state(sp->pdev);
+ pci_read_config_word(sp->pdev, 0x2, &val16);
+ if (check_pci_device_id(val16) != (u16)PCI_ANY_ID)
+ break;
+ msleep(200);
+ }
- msleep(250);
+ if (check_pci_device_id(val16) == (u16)PCI_ANY_ID) {
+ DBG_PRINT(ERR_DBG,"%s SW_Reset failed!\n", __FUNCTION__);
+ }
+
+ pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, pci_cmd);
+
+ s2io_init_pci(sp);
/* Set swapper to enable I/O register access */
s2io_set_swapper(sp);
}
offload_type = s2io_offload_type(skb);
-#ifdef NETIF_F_TSO
if (offload_type & (SKB_GSO_TCPV4 | SKB_GSO_TCPV6)) {
txdp->Control_1 |= TXD_TCP_LSO_EN;
txdp->Control_1 |= TXD_TCP_LSO_MSS(s2io_tcp_mss(skb));
}
-#endif
if (skb->ip_summed == CHECKSUM_PARTIAL) {
txdp->Control_2 |=
(TXD_TX_CKO_IPV4_EN | TXD_TX_CKO_TCP_EN |
}
else if (val64 & GPIO_INT_REG_LINK_UP) {
val64 = readq(&bar0->adapter_status);
- if (verify_xena_quiescence(sp, val64,
- sp->device_enabled_once)) {
/* Enable Adapter */
- val64 = readq(&bar0->adapter_control);
- val64 |= ADAPTER_CNTL_EN;
- writeq(val64, &bar0->adapter_control);
- val64 |= ADAPTER_LED_ON;
- writeq(val64, &bar0->adapter_control);
- if (!sp->device_enabled_once)
- sp->device_enabled_once = 1;
+ val64 = readq(&bar0->adapter_control);
+ val64 |= ADAPTER_CNTL_EN;
+ writeq(val64, &bar0->adapter_control);
+ val64 |= ADAPTER_LED_ON;
+ writeq(val64, &bar0->adapter_control);
+ if (!sp->device_enabled_once)
+ sp->device_enabled_once = 1;
- s2io_link(sp, LINK_UP);
- /*
- * unmask link down interrupt and mask link-up
- * intr
- */
- val64 = readq(&bar0->gpio_int_mask);
- val64 &= ~GPIO_INT_MASK_LINK_DOWN;
- val64 |= GPIO_INT_MASK_LINK_UP;
- writeq(val64, &bar0->gpio_int_mask);
+ s2io_link(sp, LINK_UP);
+ /*
+ * unmask link down interrupt and mask link-up
+ * intr
+ */
+ val64 = readq(&bar0->gpio_int_mask);
+ val64 &= ~GPIO_INT_MASK_LINK_DOWN;
+ val64 |= GPIO_INT_MASK_LINK_UP;
+ writeq(val64, &bar0->gpio_int_mask);
- }
}else if (val64 & GPIO_INT_REG_LINK_DOWN) {
val64 = readq(&bar0->adapter_status);
- if (verify_xena_quiescence(sp, val64,
- sp->device_enabled_once)) {
- s2io_link(sp, LINK_DOWN);
- /* Link is down so unmaks link up interrupt */
- val64 = readq(&bar0->gpio_int_mask);
- val64 &= ~GPIO_INT_MASK_LINK_UP;
- val64 |= GPIO_INT_MASK_LINK_DOWN;
- writeq(val64, &bar0->gpio_int_mask);
- }
+ s2io_link(sp, LINK_DOWN);
+ /* Link is down so unmaks link up interrupt */
+ val64 = readq(&bar0->gpio_int_mask);
+ val64 &= ~GPIO_INT_MASK_LINK_UP;
+ val64 |= GPIO_INT_MASK_LINK_DOWN;
+ writeq(val64, &bar0->gpio_int_mask);
}
}
val64 = readq(&bar0->gpio_int_mask);
nic_t *sp = dev->priv;
XENA_dev_config_t __iomem *bar0 = sp->bar0;
int i;
- u64 reason = 0, val64, org_mask;
+ u64 reason = 0;
mac_info_t *mac_control;
struct config_param *config;
reason = readq(&bar0->general_int_status);
if (!reason) {
- /* The interrupt was not raised by Xena. */
+ /* The interrupt was not raised by us. */
+ atomic_dec(&sp->isr_cnt);
+ return IRQ_NONE;
+ }
+ else if (unlikely(reason == S2IO_MINUS_ONE) ) {
+ /* Disable device and get out */
atomic_dec(&sp->isr_cnt);
return IRQ_NONE;
}
- val64 = 0xFFFFFFFFFFFFFFFFULL;
- /* Store current mask before masking all interrupts */
- org_mask = readq(&bar0->general_int_mask);
- writeq(val64, &bar0->general_int_mask);
+ if (napi) {
+ if (reason & GEN_INTR_RXTRAFFIC) {
+ if ( likely ( netif_rx_schedule_prep(dev)) ) {
+ __netif_rx_schedule(dev);
+ writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_mask);
+ }
+ else
+ writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
+ }
+ } else {
+ /*
+ * Rx handler is called by default, without checking for the
+ * cause of interrupt.
+ * rx_traffic_int reg is an R1 register, writing all 1's
+ * will ensure that the actual interrupt causing bit get's
+ * cleared and hence a read can be avoided.
+ */
+ if (reason & GEN_INTR_RXTRAFFIC)
+ writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
-#ifdef CONFIG_S2IO_NAPI
- if (reason & GEN_INTR_RXTRAFFIC) {
- if (netif_rx_schedule_prep(dev)) {
- writeq(val64, &bar0->rx_traffic_mask);
- __netif_rx_schedule(dev);
+ for (i = 0; i < config->rx_ring_num; i++) {
+ rx_intr_handler(&mac_control->rings[i]);
}
}
-#else
- /*
- * Rx handler is called by default, without checking for the
- * cause of interrupt.
- * rx_traffic_int reg is an R1 register, writing all 1's
- * will ensure that the actual interrupt causing bit get's
- * cleared and hence a read can be avoided.
- */
- writeq(val64, &bar0->rx_traffic_int);
- for (i = 0; i < config->rx_ring_num; i++) {
- rx_intr_handler(&mac_control->rings[i]);
- }
-#endif
/*
* tx_traffic_int reg is an R1 register, writing all 1's
* will ensure that the actual interrupt causing bit get's
* cleared and hence a read can be avoided.
*/
- writeq(val64, &bar0->tx_traffic_int);
+ if (reason & GEN_INTR_TXTRAFFIC)
+ writeq(S2IO_MINUS_ONE, &bar0->tx_traffic_int);
for (i = 0; i < config->tx_fifo_num; i++)
tx_intr_handler(&mac_control->fifos[i]);
* reallocate the buffers from the interrupt handler itself,
* else schedule a tasklet to reallocate the buffers.
*/
-#ifndef CONFIG_S2IO_NAPI
- for (i = 0; i < config->rx_ring_num; i++)
- s2io_chk_rx_buffers(sp, i);
-#endif
- writeq(org_mask, &bar0->general_int_mask);
+ if (!napi) {
+ for (i = 0; i < config->rx_ring_num; i++)
+ s2io_chk_rx_buffers(sp, i);
+ }
+
+ writeq(0, &bar0->general_int_mask);
+ readl(&bar0->general_int_status);
+
atomic_dec(&sp->isr_cnt);
return IRQ_HANDLED;
}
strcpy(nic->product_name, "Xframe I 10GbE network adapter");
vpd_addr = 0x50;
}
+ strcpy(nic->serial_num, "NOT AVAILABLE");
vpd_data = kmalloc(256, GFP_KERNEL);
if (!vpd_data)
pci_read_config_dword(nic->pdev, (vpd_addr + 4),
(u32 *)&vpd_data[i]);
}
- if ((!fail) && (vpd_data[1] < VPD_PRODUCT_NAME_LEN)) {
+
+ if(!fail) {
+ /* read serial number of adapter */
+ for (cnt = 0; cnt < 256; cnt++) {
+ if ((vpd_data[cnt] == 'S') &&
+ (vpd_data[cnt+1] == 'N') &&
+ (vpd_data[cnt+2] < VPD_STRING_LEN)) {
+ memset(nic->serial_num, 0, VPD_STRING_LEN);
+ memcpy(nic->serial_num, &vpd_data[cnt + 3],
+ vpd_data[cnt+2]);
+ break;
+ }
+ }
+ }
+
+ if ((!fail) && (vpd_data[1] < VPD_STRING_LEN)) {
memset(nic->product_name, 0, vpd_data[1]);
memcpy(nic->product_name, &vpd_data[3], vpd_data[1]);
}
.set_tx_csum = s2io_ethtool_op_set_tx_csum,
.get_sg = ethtool_op_get_sg,
.set_sg = ethtool_op_set_sg,
-#ifdef NETIF_F_TSO
.get_tso = s2io_ethtool_op_get_tso,
.set_tso = s2io_ethtool_op_set_tso,
-#endif
.get_ufo = ethtool_op_get_ufo,
.set_ufo = ethtool_op_set_ufo,
.self_test_count = s2io_ethtool_self_test_count,
* Description: Sets the link status for the adapter
*/
-static void s2io_set_link(unsigned long data)
+static void s2io_set_link(struct work_struct *work)
{
- nic_t *nic = (nic_t *) data;
+ nic_t *nic = container_of(work, nic_t, set_link_task);
struct net_device *dev = nic->dev;
XENA_dev_config_t __iomem *bar0 = nic->bar0;
register u64 val64;
}
val64 = readq(&bar0->adapter_status);
- if (verify_xena_quiescence(nic, val64, nic->device_enabled_once)) {
- if (LINK_IS_UP(val64)) {
- val64 = readq(&bar0->adapter_control);
- val64 |= ADAPTER_CNTL_EN;
- writeq(val64, &bar0->adapter_control);
- if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
- subid)) {
- val64 = readq(&bar0->gpio_control);
- val64 |= GPIO_CTRL_GPIO_0;
- writeq(val64, &bar0->gpio_control);
- val64 = readq(&bar0->gpio_control);
- } else {
- val64 |= ADAPTER_LED_ON;
+ if (LINK_IS_UP(val64)) {
+ if (!(readq(&bar0->adapter_control) & ADAPTER_CNTL_EN)) {
+ if (verify_xena_quiescence(nic)) {
+ val64 = readq(&bar0->adapter_control);
+ val64 |= ADAPTER_CNTL_EN;
writeq(val64, &bar0->adapter_control);
- }
- if (s2io_link_fault_indication(nic) ==
- MAC_RMAC_ERR_TIMER) {
- val64 = readq(&bar0->adapter_status);
- if (!LINK_IS_UP(val64)) {
- DBG_PRINT(ERR_DBG, "%s:", dev->name);
- DBG_PRINT(ERR_DBG, " Link down");
- DBG_PRINT(ERR_DBG, "after ");
- DBG_PRINT(ERR_DBG, "enabling ");
- DBG_PRINT(ERR_DBG, "device \n");
+ if (CARDS_WITH_FAULTY_LINK_INDICATORS(
+ nic->device_type, subid)) {
+ val64 = readq(&bar0->gpio_control);
+ val64 |= GPIO_CTRL_GPIO_0;
+ writeq(val64, &bar0->gpio_control);
+ val64 = readq(&bar0->gpio_control);
+ } else {
+ val64 |= ADAPTER_LED_ON;
+ writeq(val64, &bar0->adapter_control);
}
- }
- if (nic->device_enabled_once == FALSE) {
nic->device_enabled_once = TRUE;
+ } else {
+ DBG_PRINT(ERR_DBG, "%s: Error: ", dev->name);
+ DBG_PRINT(ERR_DBG, "device is not Quiescent\n");
+ netif_stop_queue(dev);
}
+ }
+ val64 = readq(&bar0->adapter_status);
+ if (!LINK_IS_UP(val64)) {
+ DBG_PRINT(ERR_DBG, "%s:", dev->name);
+ DBG_PRINT(ERR_DBG, " Link down after enabling ");
+ DBG_PRINT(ERR_DBG, "device \n");
+ } else
s2io_link(nic, LINK_UP);
- } else {
- if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
- subid)) {
- val64 = readq(&bar0->gpio_control);
- val64 &= ~GPIO_CTRL_GPIO_0;
- writeq(val64, &bar0->gpio_control);
- val64 = readq(&bar0->gpio_control);
- }
- s2io_link(nic, LINK_DOWN);
+ } else {
+ if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
+ subid)) {
+ val64 = readq(&bar0->gpio_control);
+ val64 &= ~GPIO_CTRL_GPIO_0;
+ writeq(val64, &bar0->gpio_control);
+ val64 = readq(&bar0->gpio_control);
}
- } else { /* NIC is not Quiescent. */
- DBG_PRINT(ERR_DBG, "%s: Error: ", dev->name);
- DBG_PRINT(ERR_DBG, "device is not Quiescent\n");
- netif_stop_queue(dev);
+ s2io_link(nic, LINK_DOWN);
}
clear_bit(0, &(nic->link_state));
}
((RxD3_t*)rxdp)->Buffer1_ptr = *temp1;
} else {
*skb = dev_alloc_skb(size);
+ if (!(*skb)) {
+ DBG_PRINT(ERR_DBG, "%s: dev_alloc_skb failed\n",
+ dev->name);
+ return -ENOMEM;
+ }
((RxD3_t*)rxdp)->Buffer2_ptr = *temp2 =
pci_map_single(sp->pdev, (*skb)->data,
dev->mtu + 4,
((RxD3_t*)rxdp)->Buffer2_ptr = *temp2;
} else {
*skb = dev_alloc_skb(size);
-
+ if (!(*skb)) {
+ DBG_PRINT(ERR_DBG, "%s: dev_alloc_skb failed\n",
+ dev->name);
+ return -ENOMEM;
+ }
((RxD3_t*)rxdp)->Buffer0_ptr = *temp0 =
pci_map_single(sp->pdev, ba->ba_0, BUF0_LEN,
PCI_DMA_FROMDEVICE);
rxd_owner_bit_reset(sp);
val64 = readq(&bar0->adapter_status);
- if (verify_xena_quiescence(sp, val64, sp->device_enabled_once)) {
+ if (verify_xena_quiescence(sp)) {
+ if(verify_pcc_quiescent(sp, sp->device_enabled_once))
break;
}
DBG_PRINT(INFO_DBG, "Buf in ring:%d is %d:\n", i,
atomic_read(&sp->rx_bufs_left[i]));
}
+ /* Maintain the state prior to the open */
+ if (sp->promisc_flg)
+ sp->promisc_flg = 0;
+ if (sp->m_cast_flg) {
+ sp->m_cast_flg = 0;
+ sp->all_multi_pos= 0;
+ }
/* Setting its receive mode */
s2io_set_multicast(dev);
* spin lock.
*/
-static void s2io_restart_nic(unsigned long data)
+static void s2io_restart_nic(struct work_struct *work)
{
- struct net_device *dev = (struct net_device *) data;
- nic_t *sp = dev->priv;
+ nic_t *sp = container_of(work, nic_t, rst_timer_task);
+ struct net_device *dev = sp->dev;
s2io_card_down(sp);
if (s2io_card_up(sp)) {
if (!sp->lro) {
skb->protocol = eth_type_trans(skb, dev);
-#ifdef CONFIG_S2IO_NAPI
if (sp->vlgrp && RXD_GET_VLAN_TAG(rxdp->Control_2)) {
/* Queueing the vlan frame to the upper layer */
- vlan_hwaccel_receive_skb(skb, sp->vlgrp,
- RXD_GET_VLAN_TAG(rxdp->Control_2));
- } else {
- netif_receive_skb(skb);
- }
-#else
- if (sp->vlgrp && RXD_GET_VLAN_TAG(rxdp->Control_2)) {
- /* Queueing the vlan frame to the upper layer */
- vlan_hwaccel_rx(skb, sp->vlgrp,
- RXD_GET_VLAN_TAG(rxdp->Control_2));
+ if (napi)
+ vlan_hwaccel_receive_skb(skb, sp->vlgrp,
+ RXD_GET_VLAN_TAG(rxdp->Control_2));
+ else
+ vlan_hwaccel_rx(skb, sp->vlgrp,
+ RXD_GET_VLAN_TAG(rxdp->Control_2));
} else {
- netif_rx(skb);
+ if (napi)
+ netif_receive_skb(skb);
+ else
+ netif_rx(skb);
}
-#endif
} else {
send_up:
queue_rx_frame(skb);
DBG_PRINT(ERR_DBG, "s2io: Default to 8 Rx rings\n");
rx_ring_num = 8;
}
-#ifdef CONFIG_S2IO_NAPI
- if (*dev_intr_type != INTA) {
- DBG_PRINT(ERR_DBG, "s2io: NAPI cannot be enabled when "
- "MSI/MSI-X is enabled. Defaulting to INTA\n");
- *dev_intr_type = INTA;
- }
-#endif
+ if (*dev_intr_type != INTA)
+ napi = 0;
+
#ifndef CONFIG_PCI_MSI
if (*dev_intr_type != INTA) {
DBG_PRINT(ERR_DBG, "s2io: This kernel does not support"
sp->bar0 = ioremap(pci_resource_start(pdev, 0),
pci_resource_len(pdev, 0));
if (!sp->bar0) {
- DBG_PRINT(ERR_DBG, "%s: S2IO: cannot remap io mem1\n",
+ DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem1\n",
dev->name);
ret = -ENOMEM;
goto bar0_remap_failed;
sp->bar1 = ioremap(pci_resource_start(pdev, 2),
pci_resource_len(pdev, 2));
if (!sp->bar1) {
- DBG_PRINT(ERR_DBG, "%s: S2IO: cannot remap io mem2\n",
+ DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem2\n",
dev->name);
ret = -ENOMEM;
goto bar1_remap_failed;
* will use eth_mac_addr() for dev->set_mac_address
* mac address will be set every time dev->open() is called
*/
-#if defined(CONFIG_S2IO_NAPI)
dev->poll = s2io_poll;
dev->weight = 32;
-#endif
#ifdef CONFIG_NET_POLL_CONTROLLER
dev->poll_controller = s2io_netpoll;
dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM;
if (sp->high_dma_flag == TRUE)
dev->features |= NETIF_F_HIGHDMA;
-#ifdef NETIF_F_TSO
dev->features |= NETIF_F_TSO;
-#endif
-#ifdef NETIF_F_TSO6
dev->features |= NETIF_F_TSO6;
-#endif
- if (sp->device_type & XFRAME_II_DEVICE) {
+ if ((sp->device_type & XFRAME_II_DEVICE) && (ufo)) {
dev->features |= NETIF_F_UFO;
dev->features |= NETIF_F_HW_CSUM;
}
dev->tx_timeout = &s2io_tx_watchdog;
dev->watchdog_timeo = WATCH_DOG_TIMEOUT;
- INIT_WORK(&sp->rst_timer_task,
- (void (*)(void *)) s2io_restart_nic, dev);
- INIT_WORK(&sp->set_link_task,
- (void (*)(void *)) s2io_set_link, sp);
+ INIT_WORK(&sp->rst_timer_task, s2io_restart_nic);
+ INIT_WORK(&sp->set_link_task, s2io_set_link);
pci_save_state(sp->pdev);
/* Initialize spinlocks */
spin_lock_init(&sp->tx_lock);
-#ifndef CONFIG_S2IO_NAPI
- spin_lock_init(&sp->put_lock);
-#endif
+
+ if (!napi)
+ spin_lock_init(&sp->put_lock);
spin_lock_init(&sp->rx_lock);
/*
DBG_PRINT(ERR_DBG, "%s: Driver version %s\n", dev->name,
s2io_driver_version);
DBG_PRINT(ERR_DBG, "%s: MAC ADDR: "
- "%02x:%02x:%02x:%02x:%02x:%02x\n", dev->name,
+ "%02x:%02x:%02x:%02x:%02x:%02x", dev->name,
sp->def_mac_addr[0].mac_addr[0],
sp->def_mac_addr[0].mac_addr[1],
sp->def_mac_addr[0].mac_addr[2],
sp->def_mac_addr[0].mac_addr[3],
sp->def_mac_addr[0].mac_addr[4],
sp->def_mac_addr[0].mac_addr[5]);
+ DBG_PRINT(ERR_DBG, "SERIAL NUMBER: %s\n", sp->serial_num);
if (sp->device_type & XFRAME_II_DEVICE) {
mode = s2io_print_pci_mode(sp);
if (mode < 0) {
dev->name);
break;
}
-#ifdef CONFIG_S2IO_NAPI
- DBG_PRINT(ERR_DBG, "%s: NAPI enabled\n", dev->name);
-#endif
+
+ if (napi)
+ DBG_PRINT(ERR_DBG, "%s: NAPI enabled\n", dev->name);
switch(sp->intr_type) {
case INTA:
DBG_PRINT(ERR_DBG, "%s: Interrupt type INTA\n", dev->name);
if (sp->lro)
DBG_PRINT(ERR_DBG, "%s: Large receive offload enabled\n",
dev->name);
-
+ if (ufo)
+ DBG_PRINT(ERR_DBG, "%s: UDP Fragmentation Offload(UFO)"
+ " enabled\n", dev->name);
/* Initialize device name */
sprintf(sp->name, "%s Neterion %s", dev->name, sp->product_name);
free_shared_mem(sp);
iounmap(sp->bar0);
iounmap(sp->bar1);
- pci_disable_device(pdev);
if (sp->intr_type != MSI_X)
pci_release_regions(pdev);
else {
}
pci_set_drvdata(pdev, NULL);
free_netdev(dev);
+ pci_disable_device(pdev);
}
/**
struct net_device *dev = skb->dev;
skb->protocol = eth_type_trans(skb, dev);
-#ifdef CONFIG_S2IO_NAPI
- netif_receive_skb(skb);
-#else
- netif_rx(skb);
-#endif
+ if (napi)
+ netif_receive_skb(skb);
+ else
+ netif_rx(skb);
}
static void lro_append_pkt(nic_t *sp, lro_t *lro, struct sk_buff *skb,
projects / linux-2.6 / blobdiff