them to system IRQ numbers. This mapping is card specific and is set to
the configuration of the Cirrus Eval board for this chip. */
#ifdef CONFIG_ARCH_CLPS7500
-static unsigned int netcard_portlist[] __initdata =
+static unsigned int netcard_portlist[] __used __initdata =
{ 0x80090303, 0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0};
static unsigned int cs8900_irq_map[] = {12,0,0,0};
#elif defined(CONFIG_SH_HICOSH4)
-static unsigned int netcard_portlist[] __initdata =
+static unsigned int netcard_portlist[] __used __initdata =
{ 0x0300, 0};
static unsigned int cs8900_irq_map[] = {1,0,0,0};
#elif defined(CONFIG_MACH_IXDP2351)
-static unsigned int netcard_portlist[] __initdata = {IXDP2351_VIRT_CS8900_BASE, 0};
+static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0};
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0};
#include <asm/irq.h>
#elif defined(CONFIG_ARCH_IXDP2X01)
#include <asm/irq.h>
-static unsigned int netcard_portlist[] __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0};
+static unsigned int netcard_portlist[] __used __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0};
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0};
#elif defined(CONFIG_ARCH_PNX010X)
#include <asm/irq.h>
#include <asm/arch/gpio.h>
#define CIRRUS_DEFAULT_BASE IO_ADDRESS(EXT_STATIC2_s0_BASE + 0x200000) /* = Physical address 0x48200000 */
#define CIRRUS_DEFAULT_IRQ VH_INTC_INT_NUM_CASCADED_INTERRUPT_1 /* Event inputs bank 1 - ID 35/bit 3 */
-static unsigned int netcard_portlist[] __initdata = {CIRRUS_DEFAULT_BASE, 0};
+static unsigned int netcard_portlist[] __used __initdata = {CIRRUS_DEFAULT_BASE, 0};
static unsigned int cs8900_irq_map[] = {CIRRUS_DEFAULT_IRQ, 0, 0, 0};
#else
-static unsigned int netcard_portlist[] __initdata =
+static unsigned int netcard_portlist[] __used __initdata =
{ 0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0};
static unsigned int cs8900_irq_map[] = {10,11,12,5};
#endif
#endif
if (!result) {
printk(KERN_ERR "%s: EEPROM is configured for unavailable media\n", dev->name);
- release_irq:
+release_dma:
+#if ALLOW_DMA
+ free_dma(dev->dma);
+#endif
+release_irq:
#if ALLOW_DMA
release_dma_buff(lp);
#endif
if ((result = detect_bnc(dev)) != DETECTED_NONE)
break;
printk(KERN_ERR "%s: no media detected\n", dev->name);
- goto release_irq;
+ goto release_dma;
}
switch(result) {
case DETECTED_NONE:
printk(KERN_ERR "%s: no network cable attached to configured media\n", dev->name);
- goto release_irq;
+ goto release_dma;
case DETECTED_RJ45H:
printk(KERN_INFO "%s: using half-duplex 10Base-T (RJ-45)\n", dev->name);
break;