menuconfig NETDEVICES
default y if UML
+ depends on NET
bool "Network device support"
---help---
You can say N here if you don't intend to connect your Linux box to
If you don't know what to use this for, you don't need it.
+config VETH
+ tristate "Virtual ethernet device"
+ ---help---
+ The device is an ethernet tunnel. Devices are created in pairs. When
+ one end receives the packet it appears on its pair and vice versa.
+
config NET_SB1000
tristate "General Instruments Surfboard 1000"
depends on PNP
If you don't have this card, of course say N.
+config IP1000
+ tristate "IP1000 Gigabit Ethernet support"
+ depends on PCI && EXPERIMENTAL
+ ---help---
+ This driver supports IP1000 gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called ipg. This is recommended.
+
source "drivers/net/arcnet/Kconfig"
source "drivers/net/phy/Kconfig"
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
-config SGI_IOC3_ETH_HW_RX_CSUM
- bool "Receive hardware checksums"
- depends on SGI_IOC3_ETH && INET
- default y
- help
- The SGI IOC3 network adapter supports TCP and UDP checksums in
- hardware to offload processing of these checksums from the CPU. At
- the moment only acceleration of IPv4 is supported. This option
- enables offloading for checksums on receive. If unsure, say Y.
-
-config SGI_IOC3_ETH_HW_TX_CSUM
- bool "Transmit hardware checksums"
- depends on SGI_IOC3_ETH && INET
- default y
- help
- The SGI IOC3 network adapter supports TCP and UDP checksums in
- hardware to offload processing of these checksums from the CPU. At
- the moment only acceleration of IPv4 is supported. This option
- enables offloading for checksums on transmit. If unsure, say Y.
-
config MIPS_SIM_NET
tristate "MIPS simulator Network device"
depends on MIPS_SIM
<file:Documentation/networking/net-modules.txt>. The module
will be called smc-ultra32.
+config BFIN_MAC
+ tristate "Blackfin 536/537 on-chip mac support"
+ depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
+ select CRC32
+ select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
+ help
+ This is the driver for blackfin on-chip mac device. Say Y if you want it
+ compiled into the kernel. This driver is also available as a module
+ ( = code which can be inserted in and removed from the running kernel
+ whenever you want). The module will be called bfin_mac.
+
+config BFIN_MAC_USE_L1
+ bool "Use L1 memory for rx/tx packets"
+ depends on BFIN_MAC && BF537
+ default y
+ help
+ To get maximum network performace, you should use L1 memory as rx/tx buffers.
+ Say N here if you want to reserve L1 memory for other uses.
+
+config BFIN_TX_DESC_NUM
+ int "Number of transmit buffer packets"
+ depends on BFIN_MAC
+ range 6 10 if BFIN_MAC_USE_L1
+ range 10 100
+ default "10"
+ help
+ Set the number of buffer packets used in driver.
+
+config BFIN_RX_DESC_NUM
+ int "Number of receive buffer packets"
+ depends on BFIN_MAC
+ range 20 100 if BFIN_MAC_USE_L1
+ range 20 800
+ default "20"
+ help
+ Set the number of buffer packets used in driver.
+
+config BFIN_MAC_RMII
+ bool "RMII PHY Interface (EXPERIMENTAL)"
+ depends on BFIN_MAC && EXPERIMENTAL
+ default n
+ help
+ Use Reduced PHY MII Interface
+
config SMC9194
tristate "SMC 9194 support"
depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
called apricot.
config B44
- tristate "Broadcom 4400 ethernet support"
- depends on NET_PCI && PCI
+ tristate "Broadcom 440x/47xx ethernet support"
+ depends on SSB_POSSIBLE
+ select SSB
select MII
help
- If you have a network (Ethernet) controller of this type, say Y and
- read the Ethernet-HOWTO, available from
+ If you have a network (Ethernet) controller of this type, say Y
+ or M and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here and read
<file:Documentation/networking/net-modules.txt>. The module will be
called b44.
+# Auto-select SSB PCI-HOST support, if possible
+config B44_PCI_AUTOSELECT
+ bool
+ depends on B44 && SSB_PCIHOST_POSSIBLE
+ select SSB_PCIHOST
+ default y
+
+# Auto-select SSB PCICORE driver, if possible
+config B44_PCICORE_AUTOSELECT
+ bool
+ depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
+ select SSB_DRIVER_PCICORE
+ default y
+
+config B44_PCI
+ bool
+ depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
+ default y
+
config FORCEDETH
tristate "nForce Ethernet support"
depends on NET_PCI && PCI
bool "Ethernet (1000 Mbit)"
depends on !UML
default y
+ ---help---
+ Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
+ type of Local Area Network (LAN) in universities and companies.
+
+ Say Y here to get to see options for Gigabit Ethernet drivers.
+ This option alone does not add any kernel code.
+ Note that drivers supporting both 100 and 1000 MBit may be listed
+ under "Ethernet (10 or 100MBit)" instead.
+
+ If you say N, all options in this submenu will be skipped and disabled.
if NETDEV_1000
The safe and default value for this is N.
config DL2K
- tristate "D-Link DL2000-based Gigabit Ethernet support"
+ tristate "DL2000/TC902x-based Gigabit Ethernet support"
depends on PCI
select CRC32
help
- This driver supports D-Link 2000-based gigabit ethernet cards, which
- includes
+ This driver supports DL2000/TC902x-based Gigabit ethernet cards,
+ which includes
D-Link DGE-550T Gigabit Ethernet Adapter.
D-Link DL2000-based Gigabit Ethernet Adapter.
+ Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
To compile this driver as a module, choose M here: the
module will be called dl2k.
If in doubt, say N.
+config E1000E
+ tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
+ depends on PCI
+ ---help---
+ This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
+ ethernet family of adapters. For PCI or PCI-X e1000 adapters,
+ use the regular e1000 driver For more information on how to
+ identify your adapter, go to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/e1000e.txt>.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called e1000e.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
with better performance and more complete ethtool support.
It does not support the link failover and network management
- features available in the hardware.
+ features that "portable" vendor supplied sk98lin driver does.
This driver supports adapters based on the original Yukon chipset:
Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
If unsure, say N.
+config SK98LIN
+ tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support (DEPRECATED)"
+ depends on PCI
+ ---help---
+ Say Y here if you have a Marvell Yukon or SysKonnect SK-98xx/SK-95xx
+ compliant Gigabit Ethernet Adapter.
+
+ This driver supports the original Yukon chipset. This driver is
+ deprecated and will be removed from the kernel in the near future,
+ it has been replaced by the skge driver. skge is cleaner and
+ seems to work better.
+
+ This driver does not support the newer Yukon2 chipset. A separate
+ driver, sky2, is provided to support Yukon2-based adapters.
+
+ The following adapters are supported by this driver:
+ - 3Com 3C940 Gigabit LOM Ethernet Adapter
+ - 3Com 3C941 Gigabit LOM Ethernet Adapter
+ - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter
+ - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
+ - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
+ - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
+ - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter
+ - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
+ - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
+ - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
+ - Belkin Gigabit Desktop Card 10/100/1000Base-T Adapter, Copper RJ-45
+ - EG1032 v2 Instant Gigabit Network Adapter
+ - EG1064 v2 Instant Gigabit Network Adapter
+ - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Abit)
+ - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Albatron)
+ - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Asus)
+ - Marvell 88E8001 Gigabit LOM Ethernet Adapter (ECS)
+ - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Epox)
+ - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Foxconn)
+ - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Gigabyte)
+ - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Iwill)
+ - Marvell 88E8050 Gigabit LOM Ethernet Adapter (Intel)
+ - Marvell RDK-8001 Adapter
+ - Marvell RDK-8002 Adapter
+ - Marvell RDK-8003 Adapter
+ - Marvell RDK-8004 Adapter
+ - Marvell RDK-8006 Adapter
+ - Marvell RDK-8007 Adapter
+ - Marvell RDK-8008 Adapter
+ - Marvell RDK-8009 Adapter
+ - Marvell RDK-8010 Adapter
+ - Marvell RDK-8011 Adapter
+ - Marvell RDK-8012 Adapter
+ - Marvell RDK-8052 Adapter
+ - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (32 bit)
+ - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (64 bit)
+ - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
+ - SK-9521 10/100/1000Base-T Adapter
+ - SK-9521 V2.0 10/100/1000Base-T Adapter
+ - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T)
+ - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
+ - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link)
+ - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX)
+ - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
+ - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link)
+ - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX)
+ - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
+ - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link)
+ - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
+ - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition)
+ - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
+ - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link)
+ - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX)
+ - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter
+ - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
+ - SMC EZ Card 1000 (SMC9452TXV.2)
+
+ The adapters support Jumbo Frames.
+ The dual link adapters support link-failover and dual port features.
+ Both Marvell Yukon and SysKonnect SK-98xx/SK-95xx adapters support
+ the scatter-gather functionality with sendfile(). Please refer to
+ <file:Documentation/networking/sk98lin.txt> for more information about
+ optional driver parameters.
+ Questions concerning this driver may be addressed to:
+ <linux@syskonnect.de>
+
+ If you want to compile this driver as a module ( = code which can be
+ inserted in and removed from the running kernel whenever you want),
+ say M here and read <file:Documentation/kbuild/modules.txt>. The module will
+ be called sk98lin. This is recommended.
+
config VIA_VELOCITY
tristate "VIA Velocity support"
depends on PCI
bool "Ethernet (10000 Mbit)"
depends on !UML
default y
+ ---help---
+ Say Y here to get to see options for 10 Gigabit Ethernet drivers.
+ This option alone does not add any kernel code.
+
+ If you say N, all options in this submenu will be skipped and disabled.
if NETDEV_10000
config EHEA
tristate "eHEA Ethernet support"
depends on IBMEBUS
+ select INET_LRO
---help---
This driver supports the IBM pSeries eHEA ethernet adapter.
To compile the driver as a module, choose M here. The module
will be called ehea.
+config IXGBE
+ tristate "Intel(R) 10GbE PCI Express adapters support"
+ depends on PCI
+ ---help---
+ This driver supports Intel(R) 10GbE PCI Express family of
+ adapters. For more information on how to identify your adapter, go
+ to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/ixgbe.txt>.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called ixgbe.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
---help---
- This driver supports Intel(R) PRO/10GbE family of
- adapters. For more information on how to identify your adapter, go
+ This driver supports Intel(R) PRO/10GbE family of adapters for
+ PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver
+ instead. For more information on how to identify your adapter, go
to the Adapter & Driver ID Guide at:
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
depends on PCI
select FW_LOADER
select CRC32
+ select INET_LRO
---help---
This driver supports Myricom Myri-10G Dual Protocol interface in
Ethernet mode. If the eeprom on your board is not recent enough,
debug_level module parameter (which can also be set after
the driver is loaded through sysfs).
+config TEHUTI
+ tristate "Tehuti Networks 10G Ethernet"
+ depends on PCI
+ help
+ Tehuti Networks 10G Ethernet NIC
+
endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
config PPPOL2TP
tristate "PPP over L2TP (EXPERIMENTAL)"
- depends on EXPERIMENTAL && PPP
+ depends on EXPERIMENTAL && PPP && INET
help
Support for PPP-over-L2TP socket family. L2TP is a protocol
used by ISPs and enterprises to tunnel PPP traffic over UDP
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
+config NETCONSOLE_DYNAMIC
+ bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
+ depends on NETCONSOLE && SYSFS && EXPERIMENTAL
+ select CONFIGFS_FS
+ help
+ This option enables the ability to dynamically reconfigure target
+ parameters (interface, IP addresses, port numbers, MAC addresses)
+ at runtime through a userspace interface exported using configfs.
+ See <file:Documentation/networking/netconsole.txt> for details.
+
config NETPOLL
def_bool NETCONSOLE
projects / linux-2.6 / blobdiff