config MACB
tristate "Atmel MACB support"
- depends on NET_ETHERNET && AVR32
+ depends on NET_ETHERNET && (AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263)
select MII
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
To compile this driver as a module, choose M here: the module
will be called bmac.
-config OAKNET
- tristate "National DP83902AV (Oak ethernet) support"
- depends on NET_ETHERNET && PPC && BROKEN
- select CRC32
- help
- Say Y if your machine has this type of Ethernet network card.
-
- To compile this driver as a module, choose M here: the module
- will be called oaknet.
-
config ARIADNE
tristate "Ariadne support"
depends on NET_ETHERNET && ZORRO
<file:Documentation/networking/net-modules.txt>. The module
will be called seeq8005.
-config SKMC
- tristate "SKnet MCA support"
- depends on NET_ETHERNET && MCA && BROKEN
- ---help---
- These are Micro Channel Ethernet adapters. You need to say Y to "MCA
- support" in order to use this driver. Supported cards are the SKnet
- Junior MC2 and the SKnet MC2(+). The driver automatically
- distinguishes between the two cards. Note that using multiple boards
- of different type hasn't been tested with this driver. Say Y if you
- have one of these Ethernet adapters.
-
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
- will be called sk_mca.
-
config NE2_MCA
tristate "NE/2 (ne2000 MCA version) support"
depends on NET_ETHERNET && MCA_LEGACY
workstations.
See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>.
+config SC92031
+ tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
+ depends on NET_PCI && PCI && EXPERIMENTAL
+ select CRC32
+ ---help---
+ This is a driver for the Fast Ethernet PCI network cards based on
+ the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
+ have one of these, say Y here.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sc92031. This is recommended.
+
config NET_POCKET
bool "Pocket and portable adapters"
depends on NET_ETHERNET && PARPORT
To compile this driver as a module, choose M here: the module
will be called qla3xxx.
+config ATL1
+ tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)"
+ depends on NET_PCI && PCI && EXPERIMENTAL
+ select CRC32
+ select MII
+ help
+ This driver supports the Attansic L1 gigabit ethernet adapter.
+
+ To compile this driver as a module, choose M here. The module
+ will be called atl1.
+
endmenu
#
Enables support for Chelsio's gigabit Ethernet PCI cards. If you
are using only 10G cards say 'N' here.
+config CHELSIO_T1_NAPI
+ bool "Use Rx Polling (NAPI)"
+ depends on CHELSIO_T1
+ default y
+ help
+ NAPI is a driver API designed to reduce CPU and interrupt load
+ when the driver is receiving lots of packets from the card.
+
+config CHELSIO_T3
+ tristate "Chelsio Communications T3 10Gb Ethernet support"
+ depends on PCI
+ help
+ This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
+ adapters.
+
+ For general information about Chelsio and our products, visit
+ our website at <http://www.chelsio.com>.
+
+ For customer support, please visit our customer support page at
+ <http://www.chelsio.com/support.htm>.
+
+ Please send feedback to <linux-bugs@chelsio.com>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called cxgb3.
+
config EHEA
tristate "eHEA Ethernet support"
depends on IBMEBUS
help
This enables the support for NetXen's Gigabit Ethernet card.
+config PASEMI_MAC
+ tristate "PA Semi 1/10Gbit MAC"
+ depends on PPC64 && PCI
+ help
+ This driver supports the on-chip 1/10Gbit Ethernet controller on
+ PA Semi's PWRficient line of chips.
+
endmenu
source "drivers/net/tokenring/Kconfig"
config SKFP
tristate "SysKonnect FDDI PCI support"
depends on FDDI && PCI
+ select BITREVERSE
---help---
Say Y here if you have a SysKonnect FDDI PCI adapter.
The following adapters are supported by this driver: