b43: Add HostFlags HI support

[linux-2.6] / drivers / leds / Kconfig

diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index cf3a6d4d947567297d5d999684b2faa27a311419..859814f62cb07e5f1e14ea71c012a70560e988e9 100644 (file)
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -18,6 +18,13 @@ config LEDS_CLASS
 
 comment "LED drivers"
 
+config LEDS_ATMEL_PWM
+       tristate "LED Support using Atmel PWM outputs"
+       depends on LEDS_CLASS && ATMEL_PWM
+       help
+         This option enables support for LEDs driven using outputs
+         of the dedicated PWM controller found on newer Atmel SOCs.
+
 config LEDS_CORGI
        tristate "LED Support for the Sharp SL-C7x0 series"
        depends on LEDS_CLASS && PXA_SHARP_C7xx
@@ -39,15 +46,6 @@ config LEDS_SPITZ
          This option enables support for the LEDs on Sharp Zaurus
          SL-Cxx00 series (C1000, C3000, C3100).
 
-config LEDS_IXP4XX
-       tristate "LED Support for GPIO connected LEDs on IXP4XX processors"
-       depends on LEDS_CLASS && ARCH_IXP4XX
-       help
-         This option enables support for the LEDs connected to GPIO
-         outputs of the Intel IXP4XX processors.  To be useful the
-         particular board must have LEDs and they must be connected
-         to the GPIO lines.  If unsure, say Y.
-
 config LEDS_TOSA
        tristate "LED Support for the Sharp SL-6000 series"
        depends on LEDS_CLASS && PXA_SHARPSL
@@ -100,6 +98,13 @@ config LEDS_COBALT_RAQ
        help
          This option enables support for the Cobalt Raq series LEDs.
 
+config LEDS_HP6XX
+       tristate "LED Support for the HP Jornada 6xx"
+       depends on LEDS_CLASS && SH_HP6XX
+       help
+         This option enables led support for the handheld
+         HP Jornada 620/660/680/690.
+
 config LEDS_GPIO
        tristate "LED Support for GPIO connected LEDs"
        depends on LEDS_CLASS && GENERIC_GPIO
@@ -122,9 +127,11 @@ config LEDS_CLEVO_MAIL
          programs through the leds subsystem. This LED have three
          known mode: off, blink at 0.5Hz and blink at 1Hz.
 
-         As this LED cannot change it's brightness it blinks instead.
-         The brightness value 0 means off, 1..127 means blink at 0.5Hz
-         and 128..255 means blink at 1Hz.
+         The driver supports two kinds of interface: using ledtrig-timer
+         or through /sys/class/leds/clevo::mail/brightness. As this LED
+         cannot change it's brightness it blinks instead. The brightness
+         value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
+         blink at 1Hz.
 
          This module can drive the mail LED for the following notebooks:
 
@@ -152,7 +159,11 @@ config LEDS_TRIGGER_TIMER
        depends on LEDS_TRIGGERS
        help
          This allows LEDs to be controlled by a programmable timer
-         via sysfs. If unsure, say Y.
+         via sysfs. Some LED hardware can be programmed to start
+         blinking the LED without any further software interaction.
+         For more details read Documentation/leds-class.txt.
+
+         If unsure, say Y.
 
 config LEDS_TRIGGER_IDE_DISK
        bool "LED IDE Disk Trigger"