/*
- * Copyright (c) 2006 QLogic, Inc. All rights reserved.
+ * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved.
* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* accessing eeprom contents from within the kernel, only via sysfs.
*/
+/* Added functionality for IBA7220-based cards */
+#define IPATH_EEPROM_DEV_V1 0xA0
+#define IPATH_EEPROM_DEV_V2 0xA2
+#define IPATH_TEMP_DEV 0x98
+#define IPATH_BAD_DEV (IPATH_EEPROM_DEV_V2+2)
+#define IPATH_NO_DEV (0xFF)
+
+/*
+ * The number of I2C chains is proliferating. Table below brings
+ * some order to the madness. The basic principle is that the
+ * table is scanned from the top, and a "probe" is made to the
+ * device probe_dev. If that succeeds, the chain is considered
+ * to be of that type, and dd->i2c_chain_type is set to the index+1
+ * of the entry.
+ * The +1 is so static initialization can mean "unknown, do probe."
+ */
+static struct i2c_chain_desc {
+ u8 probe_dev; /* If seen at probe, chain is this type */
+ u8 eeprom_dev; /* Dev addr (if any) for EEPROM */
+ u8 temp_dev; /* Dev Addr (if any) for Temp-sense */
+} i2c_chains[] = {
+ { IPATH_BAD_DEV, IPATH_NO_DEV, IPATH_NO_DEV }, /* pre-iba7220 bds */
+ { IPATH_EEPROM_DEV_V1, IPATH_EEPROM_DEV_V1, IPATH_TEMP_DEV}, /* V1 */
+ { IPATH_EEPROM_DEV_V2, IPATH_EEPROM_DEV_V2, IPATH_TEMP_DEV}, /* V2 */
+ { IPATH_NO_DEV }
+};
+
enum i2c_type {
i2c_line_scl = 0,
i2c_line_sda
#define READ_CMD 1
#define WRITE_CMD 0
-static int eeprom_init;
-
-/*
- * The gpioval manipulation really should be protected by spinlocks
- * or be converted to use atomic operations.
- */
-
/**
* i2c_gpio_set - set a GPIO line
* @dd: the infinipath device
enum i2c_type line,
enum i2c_state new_line_state)
{
- u64 read_val, write_val, mask, *gpioval;
+ u64 out_mask, dir_mask, *gpioval;
+ unsigned long flags = 0;
gpioval = &dd->ipath_gpio_out;
- read_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extctrl);
- if (line == i2c_line_scl)
- mask = dd->ipath_gpio_scl;
- else
- mask = dd->ipath_gpio_sda;
- if (new_line_state == i2c_line_high)
+ if (line == i2c_line_scl) {
+ dir_mask = dd->ipath_gpio_scl;
+ out_mask = (1UL << dd->ipath_gpio_scl_num);
+ } else {
+ dir_mask = dd->ipath_gpio_sda;
+ out_mask = (1UL << dd->ipath_gpio_sda_num);
+ }
+
+ spin_lock_irqsave(&dd->ipath_gpio_lock, flags);
+ if (new_line_state == i2c_line_high) {
/* tri-state the output rather than force high */
- write_val = read_val & ~mask;
- else
+ dd->ipath_extctrl &= ~dir_mask;
+ } else {
/* config line to be an output */
- write_val = read_val | mask;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, write_val);
+ dd->ipath_extctrl |= dir_mask;
+ }
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, dd->ipath_extctrl);
- /* set high and verify */
+ /* set output as well (no real verify) */
if (new_line_state == i2c_line_high)
- write_val = 0x1UL;
+ *gpioval |= out_mask;
else
- write_val = 0x0UL;
+ *gpioval &= ~out_mask;
- if (line == i2c_line_scl) {
- write_val <<= dd->ipath_gpio_scl_num;
- *gpioval = *gpioval & ~(1UL << dd->ipath_gpio_scl_num);
- *gpioval |= write_val;
- } else {
- write_val <<= dd->ipath_gpio_sda_num;
- *gpioval = *gpioval & ~(1UL << dd->ipath_gpio_sda_num);
- *gpioval |= write_val;
- }
ipath_write_kreg(dd, dd->ipath_kregs->kr_gpio_out, *gpioval);
+ spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags);
return 0;
}
enum i2c_type line,
enum i2c_state *curr_statep)
{
- u64 read_val, write_val, mask;
+ u64 read_val, mask;
int ret;
+ unsigned long flags = 0;
/* check args */
if (curr_statep == NULL) {
goto bail;
}
- read_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extctrl);
/* config line to be an input */
if (line == i2c_line_scl)
mask = dd->ipath_gpio_scl;
else
mask = dd->ipath_gpio_sda;
- write_val = read_val & ~mask;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, write_val);
+
+ spin_lock_irqsave(&dd->ipath_gpio_lock, flags);
+ dd->ipath_extctrl &= ~mask;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, dd->ipath_extctrl);
+ /*
+ * Below is very unlikely to reflect true input state if Output
+ * Enable actually changed.
+ */
read_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
+ spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags);
if (read_val & mask)
*curr_statep = i2c_line_high;
static void scl_out(struct ipath_devdata *dd, u8 bit)
{
+ udelay(1);
i2c_gpio_set(dd, i2c_line_scl, bit ? i2c_line_high : i2c_line_low);
i2c_wait_for_writes(dd);
return ack_received;
}
+/**
+ * rd_byte - read a byte, leaving ACK, STOP, etc up to caller
+ * @dd: the infinipath device
+ *
+ * Returns byte shifted out of device
+ */
+static int rd_byte(struct ipath_devdata *dd)
+{
+ int bit_cntr, data;
+
+ data = 0;
+
+ for (bit_cntr = 7; bit_cntr >= 0; --bit_cntr) {
+ data <<= 1;
+ scl_out(dd, i2c_line_high);
+ data |= sda_in(dd, 0);
+ scl_out(dd, i2c_line_low);
+ }
+ return data;
+}
+
/**
* wr_byte - write a byte, one bit at a time
* @dd: the infinipath device
int clock_cycles_left = 9;
u64 *gpioval = &dd->ipath_gpio_out;
int ret;
+ unsigned long flags;
- eeprom_init = 1;
+ spin_lock_irqsave(&dd->ipath_gpio_lock, flags);
+ /* Make sure shadows are consistent */
+ dd->ipath_extctrl = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extctrl);
*gpioval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_gpio_out);
+ spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags);
+
ipath_cdbg(VERBOSE, "Resetting i2c eeprom; initial gpioout reg "
"is %llx\n", (unsigned long long) *gpioval);
scl_out(dd, i2c_line_low);
sda_out(dd, i2c_line_high);
+ /* Clock up to 9 cycles looking for SDA hi, then issue START and STOP */
while (clock_cycles_left--) {
scl_out(dd, i2c_line_high);
+ /* SDA seen high, issue START by dropping it while SCL high */
if (sda_in(dd, 0)) {
sda_out(dd, i2c_line_low);
scl_out(dd, i2c_line_low);
+ /* ATMEL spec says must be followed by STOP. */
+ scl_out(dd, i2c_line_high);
+ sda_out(dd, i2c_line_high);
ret = 0;
goto bail;
}
return ret;
}
-/**
- * ipath_eeprom_read - receives bytes from the eeprom via I2C
- * @dd: the infinipath device
- * @eeprom_offset: address to read from
- * @buffer: where to store result
- * @len: number of bytes to receive
+/*
+ * Probe for I2C device at specified address. Returns 0 for "success"
+ * to match rest of this file.
+ * Leave bus in "reasonable" state for further commands.
*/
+static int i2c_probe(struct ipath_devdata *dd, int devaddr)
+{
+ int ret = 0;
-int ipath_eeprom_read(struct ipath_devdata *dd, u8 eeprom_offset,
- void *buffer, int len)
+ ret = eeprom_reset(dd);
+ if (ret) {
+ ipath_dev_err(dd, "Failed reset probing device 0x%02X\n",
+ devaddr);
+ return ret;
+ }
+ /*
+ * Reset no longer leaves bus in start condition, so normal
+ * i2c_startcmd() will do.
+ */
+ ret = i2c_startcmd(dd, devaddr | READ_CMD);
+ if (ret)
+ ipath_cdbg(VERBOSE, "Failed startcmd for device 0x%02X\n",
+ devaddr);
+ else {
+ /*
+ * Device did respond. Complete a single-byte read, because some
+ * devices apparently cannot handle STOP immediately after they
+ * ACK the start-cmd.
+ */
+ int data;
+ data = rd_byte(dd);
+ stop_cmd(dd);
+ ipath_cdbg(VERBOSE, "Response from device 0x%02X\n", devaddr);
+ }
+ return ret;
+}
+
+/*
+ * Returns the "i2c type". This is a pointer to a struct that describes
+ * the I2C chain on this board. To minimize impact on struct ipath_devdata,
+ * the (small integer) index into the table is actually memoized, rather
+ * then the pointer.
+ * Memoization is because the type is determined on the first call per chip.
+ * An alternative would be to move type determination to early
+ * init code.
+ */
+static struct i2c_chain_desc *ipath_i2c_type(struct ipath_devdata *dd)
{
- /* compiler complains unless initialized */
- u8 single_byte = 0;
- int bit_cntr;
- int ret;
+ int idx;
+
+ /* Get memoized index, from previous successful probes */
+ idx = dd->ipath_i2c_chain_type - 1;
+ if (idx >= 0 && idx < (ARRAY_SIZE(i2c_chains) - 1))
+ goto done;
+
+ idx = 0;
+ while (i2c_chains[idx].probe_dev != IPATH_NO_DEV) {
+ /* if probe succeeds, this is type */
+ if (!i2c_probe(dd, i2c_chains[idx].probe_dev))
+ break;
+ ++idx;
+ }
- if (!eeprom_init)
+ /*
+ * Old EEPROM (first entry) may require a reset after probe,
+ * rather than being able to "start" after "stop"
+ */
+ if (idx == 0)
eeprom_reset(dd);
- eeprom_offset = (eeprom_offset << 1) | READ_CMD;
+ if (i2c_chains[idx].probe_dev == IPATH_NO_DEV)
+ idx = -1;
+ else
+ dd->ipath_i2c_chain_type = idx + 1;
+done:
+ return (idx >= 0) ? i2c_chains + idx : NULL;
+}
+
+static int ipath_eeprom_internal_read(struct ipath_devdata *dd,
+ u8 eeprom_offset, void *buffer, int len)
+{
+ int ret;
+ struct i2c_chain_desc *icd;
+ u8 *bp = buffer;
- if (i2c_startcmd(dd, eeprom_offset)) {
- ipath_dbg("Failed startcmd\n");
+ ret = 1;
+ icd = ipath_i2c_type(dd);
+ if (!icd)
+ goto bail;
+
+ if (icd->eeprom_dev == IPATH_NO_DEV) {
+ /* legacy not-really-I2C */
+ ipath_cdbg(VERBOSE, "Start command only address\n");
+ eeprom_offset = (eeprom_offset << 1) | READ_CMD;
+ ret = i2c_startcmd(dd, eeprom_offset);
+ } else {
+ /* Actual I2C */
+ ipath_cdbg(VERBOSE, "Start command uses devaddr\n");
+ if (i2c_startcmd(dd, icd->eeprom_dev | WRITE_CMD)) {
+ ipath_dbg("Failed EEPROM startcmd\n");
+ stop_cmd(dd);
+ ret = 1;
+ goto bail;
+ }
+ ret = wr_byte(dd, eeprom_offset);
+ stop_cmd(dd);
+ if (ret) {
+ ipath_dev_err(dd, "Failed to write EEPROM address\n");
+ ret = 1;
+ goto bail;
+ }
+ ret = i2c_startcmd(dd, icd->eeprom_dev | READ_CMD);
+ }
+ if (ret) {
+ ipath_dbg("Failed startcmd for dev %02X\n", icd->eeprom_dev);
stop_cmd(dd);
ret = 1;
goto bail;
* incrementing the address.
*/
while (len-- > 0) {
- /* get data */
- single_byte = 0;
- for (bit_cntr = 8; bit_cntr; bit_cntr--) {
- u8 bit;
- scl_out(dd, i2c_line_high);
- bit = sda_in(dd, 0);
- single_byte |= bit << (bit_cntr - 1);
- scl_out(dd, i2c_line_low);
- }
-
+ /* get and store data */
+ *bp++ = rd_byte(dd);
/* send ack if not the last byte */
if (len)
send_ack(dd);
-
- *((u8 *) buffer) = single_byte;
- buffer++;
}
stop_cmd(dd);
return ret;
}
-/**
- * ipath_eeprom_write - writes data to the eeprom via I2C
- * @dd: the infinipath device
- * @eeprom_offset: where to place data
- * @buffer: data to write
- * @len: number of bytes to write
- */
-int ipath_eeprom_write(struct ipath_devdata *dd, u8 eeprom_offset,
- const void *buffer, int len)
+static int ipath_eeprom_internal_write(struct ipath_devdata *dd, u8 eeprom_offset,
+ const void *buffer, int len)
{
- u8 single_byte;
int sub_len;
const u8 *bp = buffer;
int max_wait_time, i;
int ret;
+ struct i2c_chain_desc *icd;
- if (!eeprom_init)
- eeprom_reset(dd);
+ ret = 1;
+ icd = ipath_i2c_type(dd);
+ if (!icd)
+ goto bail;
while (len > 0) {
- if (i2c_startcmd(dd, (eeprom_offset << 1) | WRITE_CMD)) {
- ipath_dbg("Failed to start cmd offset %u\n",
- eeprom_offset);
- goto failed_write;
+ if (icd->eeprom_dev == IPATH_NO_DEV) {
+ if (i2c_startcmd(dd,
+ (eeprom_offset << 1) | WRITE_CMD)) {
+ ipath_dbg("Failed to start cmd offset %u\n",
+ eeprom_offset);
+ goto failed_write;
+ }
+ } else {
+ /* Real I2C */
+ if (i2c_startcmd(dd, icd->eeprom_dev | WRITE_CMD)) {
+ ipath_dbg("Failed EEPROM startcmd\n");
+ goto failed_write;
+ }
+ ret = wr_byte(dd, eeprom_offset);
+ if (ret) {
+ ipath_dev_err(dd, "Failed to write EEPROM "
+ "address\n");
+ goto failed_write;
+ }
}
sub_len = min(len, 4);
* the writes have completed. We do this inline to avoid
* the debug prints that are in the real read routine
* if the startcmd fails.
+ * We also use the proper device address, so it doesn't matter
+ * whether we have real eeprom_dev. legacy likes any address.
*/
max_wait_time = 100;
- while (i2c_startcmd(dd, READ_CMD)) {
+ while (i2c_startcmd(dd, icd->eeprom_dev | READ_CMD)) {
stop_cmd(dd);
if (!--max_wait_time) {
ipath_dbg("Did not get successful read to "
goto failed_write;
}
}
- /* now read the zero byte */
- for (i = single_byte = 0; i < 8; i++) {
- u8 bit;
- scl_out(dd, i2c_line_high);
- bit = sda_in(dd, 0);
- scl_out(dd, i2c_line_low);
- single_byte <<= 1;
- single_byte |= bit;
- }
+ /* now read (and ignore) the resulting byte */
+ rd_byte(dd);
stop_cmd(dd);
}
return ret;
}
+/**
+ * ipath_eeprom_read - receives bytes from the eeprom via I2C
+ * @dd: the infinipath device
+ * @eeprom_offset: address to read from
+ * @buffer: where to store result
+ * @len: number of bytes to receive
+ */
+int ipath_eeprom_read(struct ipath_devdata *dd, u8 eeprom_offset,
+ void *buff, int len)
+{
+ int ret;
+
+ ret = mutex_lock_interruptible(&dd->ipath_eep_lock);
+ if (!ret) {
+ ret = ipath_eeprom_internal_read(dd, eeprom_offset, buff, len);
+ mutex_unlock(&dd->ipath_eep_lock);
+ }
+
+ return ret;
+}
+
+/**
+ * ipath_eeprom_write - writes data to the eeprom via I2C
+ * @dd: the infinipath device
+ * @eeprom_offset: where to place data
+ * @buffer: data to write
+ * @len: number of bytes to write
+ */
+int ipath_eeprom_write(struct ipath_devdata *dd, u8 eeprom_offset,
+ const void *buff, int len)
+{
+ int ret;
+
+ ret = mutex_lock_interruptible(&dd->ipath_eep_lock);
+ if (!ret) {
+ ret = ipath_eeprom_internal_write(dd, eeprom_offset, buff, len);
+ mutex_unlock(&dd->ipath_eep_lock);
+ }
+
+ return ret;
+}
+
static u8 flash_csum(struct ipath_flash *ifp, int adjust)
{
u8 *ip = (u8 *) ifp;
u8 csum = 0, len;
- for (len = 0; len < ifp->if_length; len++)
+ /*
+ * Limit length checksummed to max length of actual data.
+ * Checksum of erased eeprom will still be bad, but we avoid
+ * reading past the end of the buffer we were passed.
+ */
+ len = ifp->if_length;
+ if (len > sizeof(struct ipath_flash))
+ len = sizeof(struct ipath_flash);
+ while (len--)
csum += *ip++;
csum -= ifp->if_csum;
csum = ~csum;
void *buf;
struct ipath_flash *ifp;
__be64 guid;
- int len;
+ int len, eep_stat;
u8 csum, *bguid;
int t = dd->ipath_unit;
struct ipath_devdata *dd0 = ipath_lookup(0);
if (t && dd0->ipath_nguid > 1 && t <= dd0->ipath_nguid) {
- u8 *bguid, oguid;
+ u8 oguid;
dd->ipath_guid = dd0->ipath_guid;
bguid = (u8 *) & dd->ipath_guid;
goto bail;
}
- len = offsetof(struct ipath_flash, if_future);
+ /*
+ * read full flash, not just currently used part, since it may have
+ * been written with a newer definition
+ * */
+ len = sizeof(struct ipath_flash);
buf = vmalloc(len);
if (!buf) {
ipath_dev_err(dd, "Couldn't allocate memory to read %u "
goto bail;
}
- if (ipath_eeprom_read(dd, 0, buf, len)) {
+ mutex_lock(&dd->ipath_eep_lock);
+ eep_stat = ipath_eeprom_internal_read(dd, 0, buf, len);
+ mutex_unlock(&dd->ipath_eep_lock);
+
+ if (eep_stat) {
ipath_dev_err(dd, "Failed reading GUID from eeprom\n");
goto done;
}
* elsewhere for backward-compatibility.
*/
char *snp = dd->ipath_serial;
- int len;
memcpy(snp, ifp->if_sprefix, sizeof ifp->if_sprefix);
snp[sizeof ifp->if_sprefix] = '\0';
len = strlen(snp);
} else
memcpy(dd->ipath_serial, ifp->if_serial,
sizeof ifp->if_serial);
+ if (!strstr(ifp->if_comment, "Tested successfully"))
+ ipath_dev_err(dd, "Board SN %s did not pass functional "
+ "test: %s\n", dd->ipath_serial,
+ ifp->if_comment);
ipath_cdbg(VERBOSE, "Initted GUID to %llx from eeprom\n",
(unsigned long long) be64_to_cpu(dd->ipath_guid));
+ memcpy(&dd->ipath_eep_st_errs, &ifp->if_errcntp, IPATH_EEP_LOG_CNT);
+ /*
+ * Power-on (actually "active") hours are kept as little-endian value
+ * in EEPROM, but as seconds in a (possibly as small as 24-bit)
+ * atomic_t while running.
+ */
+ atomic_set(&dd->ipath_active_time, 0);
+ dd->ipath_eep_hrs = ifp->if_powerhour[0] | (ifp->if_powerhour[1] << 8);
+
done:
vfree(buf);
bail:;
}
+
+/**
+ * ipath_update_eeprom_log - copy active-time and error counters to eeprom
+ * @dd: the infinipath device
+ *
+ * Although the time is kept as seconds in the ipath_devdata struct, it is
+ * rounded to hours for re-write, as we have only 16 bits in EEPROM.
+ * First-cut code reads whole (expected) struct ipath_flash, modifies,
+ * re-writes. Future direction: read/write only what we need, assuming
+ * that the EEPROM had to have been "good enough" for driver init, and
+ * if not, we aren't making it worse.
+ *
+ */
+
+int ipath_update_eeprom_log(struct ipath_devdata *dd)
+{
+ void *buf;
+ struct ipath_flash *ifp;
+ int len, hi_water;
+ uint32_t new_time, new_hrs;
+ u8 csum;
+ int ret, idx;
+ unsigned long flags;
+
+ /* first, check if we actually need to do anything. */
+ ret = 0;
+ for (idx = 0; idx < IPATH_EEP_LOG_CNT; ++idx) {
+ if (dd->ipath_eep_st_new_errs[idx]) {
+ ret = 1;
+ break;
+ }
+ }
+ new_time = atomic_read(&dd->ipath_active_time);
+
+ if (ret == 0 && new_time < 3600)
+ return 0;
+
+ /*
+ * The quick-check above determined that there is something worthy
+ * of logging, so get current contents and do a more detailed idea.
+ * read full flash, not just currently used part, since it may have
+ * been written with a newer definition
+ */
+ len = sizeof(struct ipath_flash);
+ buf = vmalloc(len);
+ ret = 1;
+ if (!buf) {
+ ipath_dev_err(dd, "Couldn't allocate memory to read %u "
+ "bytes from eeprom for logging\n", len);
+ goto bail;
+ }
+
+ /* Grab semaphore and read current EEPROM. If we get an
+ * error, let go, but if not, keep it until we finish write.
+ */
+ ret = mutex_lock_interruptible(&dd->ipath_eep_lock);
+ if (ret) {
+ ipath_dev_err(dd, "Unable to acquire EEPROM for logging\n");
+ goto free_bail;
+ }
+ ret = ipath_eeprom_internal_read(dd, 0, buf, len);
+ if (ret) {
+ mutex_unlock(&dd->ipath_eep_lock);
+ ipath_dev_err(dd, "Unable read EEPROM for logging\n");
+ goto free_bail;
+ }
+ ifp = (struct ipath_flash *)buf;
+
+ csum = flash_csum(ifp, 0);
+ if (csum != ifp->if_csum) {
+ mutex_unlock(&dd->ipath_eep_lock);
+ ipath_dev_err(dd, "EEPROM cks err (0x%02X, S/B 0x%02X)\n",
+ csum, ifp->if_csum);
+ ret = 1;
+ goto free_bail;
+ }
+ hi_water = 0;
+ spin_lock_irqsave(&dd->ipath_eep_st_lock, flags);
+ for (idx = 0; idx < IPATH_EEP_LOG_CNT; ++idx) {
+ int new_val = dd->ipath_eep_st_new_errs[idx];
+ if (new_val) {
+ /*
+ * If we have seen any errors, add to EEPROM values
+ * We need to saturate at 0xFF (255) and we also
+ * would need to adjust the checksum if we were
+ * trying to minimize EEPROM traffic
+ * Note that we add to actual current count in EEPROM,
+ * in case it was altered while we were running.
+ */
+ new_val += ifp->if_errcntp[idx];
+ if (new_val > 0xFF)
+ new_val = 0xFF;
+ if (ifp->if_errcntp[idx] != new_val) {
+ ifp->if_errcntp[idx] = new_val;
+ hi_water = offsetof(struct ipath_flash,
+ if_errcntp) + idx;
+ }
+ /*
+ * update our shadow (used to minimize EEPROM
+ * traffic), to match what we are about to write.
+ */
+ dd->ipath_eep_st_errs[idx] = new_val;
+ dd->ipath_eep_st_new_errs[idx] = 0;
+ }
+ }
+ /*
+ * now update active-time. We would like to round to the nearest hour
+ * but unless atomic_t are sure to be proper signed ints we cannot,
+ * because we need to account for what we "transfer" to EEPROM and
+ * if we log an hour at 31 minutes, then we would need to set
+ * active_time to -29 to accurately count the _next_ hour.
+ */
+ if (new_time >= 3600) {
+ new_hrs = new_time / 3600;
+ atomic_sub((new_hrs * 3600), &dd->ipath_active_time);
+ new_hrs += dd->ipath_eep_hrs;
+ if (new_hrs > 0xFFFF)
+ new_hrs = 0xFFFF;
+ dd->ipath_eep_hrs = new_hrs;
+ if ((new_hrs & 0xFF) != ifp->if_powerhour[0]) {
+ ifp->if_powerhour[0] = new_hrs & 0xFF;
+ hi_water = offsetof(struct ipath_flash, if_powerhour);
+ }
+ if ((new_hrs >> 8) != ifp->if_powerhour[1]) {
+ ifp->if_powerhour[1] = new_hrs >> 8;
+ hi_water = offsetof(struct ipath_flash, if_powerhour)
+ + 1;
+ }
+ }
+ /*
+ * There is a tiny possibility that we could somehow fail to write
+ * the EEPROM after updating our shadows, but problems from holding
+ * the spinlock too long are a much bigger issue.
+ */
+ spin_unlock_irqrestore(&dd->ipath_eep_st_lock, flags);
+ if (hi_water) {
+ /* we made some change to the data, uopdate cksum and write */
+ csum = flash_csum(ifp, 1);
+ ret = ipath_eeprom_internal_write(dd, 0, buf, hi_water + 1);
+ }
+ mutex_unlock(&dd->ipath_eep_lock);
+ if (ret)
+ ipath_dev_err(dd, "Failed updating EEPROM\n");
+
+free_bail:
+ vfree(buf);
+bail:
+ return ret;
+
+}
+
+/**
+ * ipath_inc_eeprom_err - increment one of the four error counters
+ * that are logged to EEPROM.
+ * @dd: the infinipath device
+ * @eidx: 0..3, the counter to increment
+ * @incr: how much to add
+ *
+ * Each counter is 8-bits, and saturates at 255 (0xFF). They
+ * are copied to the EEPROM (aka flash) whenever ipath_update_eeprom_log()
+ * is called, but it can only be called in a context that allows sleep.
+ * This function can be called even at interrupt level.
+ */
+
+void ipath_inc_eeprom_err(struct ipath_devdata *dd, u32 eidx, u32 incr)
+{
+ uint new_val;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dd->ipath_eep_st_lock, flags);
+ new_val = dd->ipath_eep_st_new_errs[eidx] + incr;
+ if (new_val > 255)
+ new_val = 255;
+ dd->ipath_eep_st_new_errs[eidx] = new_val;
+ spin_unlock_irqrestore(&dd->ipath_eep_st_lock, flags);
+ return;
+}
+
+static int ipath_tempsense_internal_read(struct ipath_devdata *dd, u8 regnum)
+{
+ int ret;
+ struct i2c_chain_desc *icd;
+
+ ret = -ENOENT;
+
+ icd = ipath_i2c_type(dd);
+ if (!icd)
+ goto bail;
+
+ if (icd->temp_dev == IPATH_NO_DEV) {
+ /* tempsense only exists on new, real-I2C boards */
+ ret = -ENXIO;
+ goto bail;
+ }
+
+ if (i2c_startcmd(dd, icd->temp_dev | WRITE_CMD)) {
+ ipath_dbg("Failed tempsense startcmd\n");
+ stop_cmd(dd);
+ ret = -ENXIO;
+ goto bail;
+ }
+ ret = wr_byte(dd, regnum);
+ stop_cmd(dd);
+ if (ret) {
+ ipath_dev_err(dd, "Failed tempsense WR command %02X\n",
+ regnum);
+ ret = -ENXIO;
+ goto bail;
+ }
+ if (i2c_startcmd(dd, icd->temp_dev | READ_CMD)) {
+ ipath_dbg("Failed tempsense RD startcmd\n");
+ stop_cmd(dd);
+ ret = -ENXIO;
+ goto bail;
+ }
+ /*
+ * We can only clock out one byte per command, sensibly
+ */
+ ret = rd_byte(dd);
+ stop_cmd(dd);
+
+bail:
+ return ret;
+}
+
+#define VALID_TS_RD_REG_MASK 0xBF
+
+/**
+ * ipath_tempsense_read - read register of temp sensor via I2C
+ * @dd: the infinipath device
+ * @regnum: register to read from
+ *
+ * returns reg contents (0..255) or < 0 for error
+ */
+int ipath_tempsense_read(struct ipath_devdata *dd, u8 regnum)
+{
+ int ret;
+
+ if (regnum > 7)
+ return -EINVAL;
+
+ /* return a bogus value for (the one) register we do not have */
+ if (!((1 << regnum) & VALID_TS_RD_REG_MASK))
+ return 0;
+
+ ret = mutex_lock_interruptible(&dd->ipath_eep_lock);
+ if (!ret) {
+ ret = ipath_tempsense_internal_read(dd, regnum);
+ mutex_unlock(&dd->ipath_eep_lock);
+ }
+
+ /*
+ * There are three possibilities here:
+ * ret is actual value (0..255)
+ * ret is -ENXIO or -EINVAL from code in this file
+ * ret is -EINTR from mutex_lock_interruptible.
+ */
+ return ret;
+}
+
+static int ipath_tempsense_internal_write(struct ipath_devdata *dd,
+ u8 regnum, u8 data)
+{
+ int ret = -ENOENT;
+ struct i2c_chain_desc *icd;
+
+ icd = ipath_i2c_type(dd);
+ if (!icd)
+ goto bail;
+
+ if (icd->temp_dev == IPATH_NO_DEV) {
+ /* tempsense only exists on new, real-I2C boards */
+ ret = -ENXIO;
+ goto bail;
+ }
+ if (i2c_startcmd(dd, icd->temp_dev | WRITE_CMD)) {
+ ipath_dbg("Failed tempsense startcmd\n");
+ stop_cmd(dd);
+ ret = -ENXIO;
+ goto bail;
+ }
+ ret = wr_byte(dd, regnum);
+ if (ret) {
+ stop_cmd(dd);
+ ipath_dev_err(dd, "Failed to write tempsense command %02X\n",
+ regnum);
+ ret = -ENXIO;
+ goto bail;
+ }
+ ret = wr_byte(dd, data);
+ stop_cmd(dd);
+ ret = i2c_startcmd(dd, icd->temp_dev | READ_CMD);
+ if (ret) {
+ ipath_dev_err(dd, "Failed tempsense data wrt to %02X\n",
+ regnum);
+ ret = -ENXIO;
+ }
+
+bail:
+ return ret;
+}
+
+#define VALID_TS_WR_REG_MASK ((1 << 9) | (1 << 0xB) | (1 << 0xD))
+
+/**
+ * ipath_tempsense_write - write register of temp sensor via I2C
+ * @dd: the infinipath device
+ * @regnum: register to write
+ * @data: data to write
+ *
+ * returns 0 for success or < 0 for error
+ */
+int ipath_tempsense_write(struct ipath_devdata *dd, u8 regnum, u8 data)
+{
+ int ret;
+
+ if (regnum > 15 || !((1 << regnum) & VALID_TS_WR_REG_MASK))
+ return -EINVAL;
+
+ ret = mutex_lock_interruptible(&dd->ipath_eep_lock);
+ if (!ret) {
+ ret = ipath_tempsense_internal_write(dd, regnum, data);
+ mutex_unlock(&dd->ipath_eep_lock);
+ }
+
+ /*
+ * There are three possibilities here:
+ * ret is 0 for success
+ * ret is -ENXIO or -EINVAL from code in this file
+ * ret is -EINTR from mutex_lock_interruptible.
+ */
+ return ret;
+}