#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/irq.h>
-#include <linux/sched.h>
#include <linux/types.h>
#include <linux/vmalloc.h>
#include <linux/init.h>
static void ohci1394_pci_remove(struct pci_dev *pdev);
#ifndef __LITTLE_ENDIAN
-const static size_t hdr_sizes[] = {
+static const size_t hdr_sizes[] = {
3, /* TCODE_WRITEQ */
4, /* TCODE_WRITEB */
3, /* TCODE_WRITE_RESPONSE */
/* Set up self-id dma buffer */
reg_write(ohci, OHCI1394_SelfIDBuffer, ohci->selfid_buf_bus);
- /* enable self-id and phys */
- reg_write(ohci, OHCI1394_LinkControlSet, OHCI1394_LinkControl_RcvSelfID |
- OHCI1394_LinkControl_RcvPhyPkt);
+ /* enable self-id */
+ reg_write(ohci, OHCI1394_LinkControlSet, OHCI1394_LinkControl_RcvSelfID);
/* Set the Config ROM mapping register */
reg_write(ohci, OHCI1394_ConfigROMmap, ohci->csr_config_rom_bus);
ohci->max_packet_size =
1<<(((reg_read(ohci, OHCI1394_BusOptions)>>12)&0xf)+1);
- /* Don't accept phy packets into AR request context */
- reg_write(ohci, OHCI1394_LinkControlClear, 0x00000400);
-
/* Clear the interrupt mask */
reg_write(ohci, OHCI1394_IsoRecvIntMaskClear, 0xffffffff);
reg_write(ohci, OHCI1394_IsoRecvIntEventClear, 0xffffffff);
#endif
PRINT(KERN_DEBUG, "Serial EEPROM has suspicious values, "
- "attempting to setting max_packet_size to 512 bytes");
+ "attempting to set max_packet_size to 512 bytes");
reg_write(ohci, OHCI1394_BusOptions,
(reg_read(ohci, OHCI1394_BusOptions) & 0xf007) | 0x8002);
ohci->max_packet_size = 512;
if (event & OHCI1394_postedWriteErr) {
PRINT(KERN_ERR, "physical posted write error");
/* no recovery strategy yet, had to involve protocol drivers */
+ event &= ~OHCI1394_postedWriteErr;
}
if (event & OHCI1394_cycleTooLong) {
if(printk_ratelimit())
struct ti_ohci *ohci; /* shortcut to currently handled device */
resource_size_t ohci_base;
+#ifdef CONFIG_PPC_PMAC
+ /* Necessary on some machines if ohci1394 was loaded/ unloaded before */
+ if (machine_is(powermac)) {
+ struct device_node *ofn = pci_device_to_OF_node(dev);
+
+ if (ofn) {
+ pmac_call_feature(PMAC_FTR_1394_CABLE_POWER, ofn, 0, 1);
+ pmac_call_feature(PMAC_FTR_1394_ENABLE, ofn, 0, 1);
+ }
+ }
+#endif /* CONFIG_PPC_PMAC */
+
if (pci_enable_device(dev))
FAIL(-ENXIO, "Failed to enable OHCI hardware");
pci_set_master(dev);
PRINT(KERN_WARNING, "PCI resource length of 0x%llx too small!",
(unsigned long long)pci_resource_len(dev, 0));
- /* Seems PCMCIA handles this internally. Not sure why. Seems
- * pretty bogus to force a driver to special case this. */
-#ifndef PCMCIA
- if (!request_mem_region (ohci_base, OHCI1394_REGISTER_SIZE, OHCI1394_DRIVER_NAME))
+ if (!request_mem_region(ohci_base, OHCI1394_REGISTER_SIZE,
+ OHCI1394_DRIVER_NAME))
FAIL(-ENOMEM, "MMIO resource (0x%llx - 0x%llx) unavailable",
(unsigned long long)ohci_base,
(unsigned long long)ohci_base + OHCI1394_REGISTER_SIZE);
-#endif
ohci->init_state = OHCI_INIT_HAVE_MEM_REGION;
ohci->registers = ioremap(ohci_base, OHCI1394_REGISTER_SIZE);
iounmap(ohci->registers);
case OHCI_INIT_HAVE_MEM_REGION:
-#ifndef PCMCIA
release_mem_region(pci_resource_start(ohci->dev, 0),
OHCI1394_REGISTER_SIZE);
-#endif
#ifdef CONFIG_PPC_PMAC
- /* On UniNorth, power down the cable and turn off the chip
- * clock when the module is removed to save power on
- * laptops. Turning it back ON is done by the arch code when
- * pci_enable_device() is called */
- {
- struct device_node* of_node;
+ /* On UniNorth, power down the cable and turn off the chip clock
+ * to save power on laptops */
+ if (machine_is(powermac)) {
+ struct device_node* ofn = pci_device_to_OF_node(ohci->dev);
- of_node = pci_device_to_OF_node(ohci->dev);
- if (of_node) {
- pmac_call_feature(PMAC_FTR_1394_ENABLE, of_node, 0, 0);
- pmac_call_feature(PMAC_FTR_1394_CABLE_POWER, of_node, 0, 0);
+ if (ofn) {
+ pmac_call_feature(PMAC_FTR_1394_ENABLE, ofn, 0, 0);
+ pmac_call_feature(PMAC_FTR_1394_CABLE_POWER, ofn, 0, 0);
}
}
#endif /* CONFIG_PPC_PMAC */
int err;
struct ti_ohci *ohci = pci_get_drvdata(pdev);
- printk(KERN_INFO "%s does not fully support suspend and resume yet\n",
- OHCI1394_DRIVER_NAME);
-
if (!ohci) {
printk(KERN_ERR "%s: tried to suspend nonexisting host\n",
OHCI1394_DRIVER_NAME);
/* PowerMac suspend code comes last */
#ifdef CONFIG_PPC_PMAC
if (machine_is(powermac)) {
- struct device_node *of_node;
+ struct device_node *ofn = pci_device_to_OF_node(pdev);
- /* Disable 1394 */
- of_node = pci_device_to_OF_node (pdev);
- if (of_node)
- pmac_call_feature(PMAC_FTR_1394_ENABLE, of_node, 0, 0);
+ if (ofn)
+ pmac_call_feature(PMAC_FTR_1394_ENABLE, ofn, 0, 0);
}
#endif /* CONFIG_PPC_PMAC */
/* PowerMac resume code comes first */
#ifdef CONFIG_PPC_PMAC
if (machine_is(powermac)) {
- struct device_node *of_node;
+ struct device_node *ofn = pci_device_to_OF_node(pdev);
- /* Re-enable 1394 */
- of_node = pci_device_to_OF_node (pdev);
- if (of_node)
- pmac_call_feature (PMAC_FTR_1394_ENABLE, of_node, 0, 1);
+ if (ofn)
+ pmac_call_feature(PMAC_FTR_1394_ENABLE, ofn, 0, 1);
}
#endif /* CONFIG_PPC_PMAC */
mdelay(50);
ohci_initialize(ohci);
+ hpsb_resume_host(ohci->host);
return 0;
}
#endif /* CONFIG_PM */
-#define PCI_CLASS_FIREWIRE_OHCI ((PCI_CLASS_SERIAL_FIREWIRE << 8) | 0x10)
-
static struct pci_device_id ohci1394_pci_tbl[] = {
{
- .class = PCI_CLASS_FIREWIRE_OHCI,
+ .class = PCI_CLASS_SERIAL_FIREWIRE_OHCI,
.class_mask = PCI_ANY_ID,
.vendor = PCI_ANY_ID,
.device = PCI_ANY_ID,
/* essentially the only purpose of this code is to allow another
module to hook into ohci's interrupt handler */
+/* returns zero if successful, one if DMA context is locked up */
int ohci1394_stop_context(struct ti_ohci *ohci, int reg, char *msg)
{
int i=0;
projects / linux-2.6 / blobdiff