#include <asm/io.h>
#include <asm/irq.h>
-
-/**
- * ide_match_hwif - match a PCI IDE against an ide_hwif
- * @io_base: I/O base of device
- * @bootable: set if its bootable
- * @name: name of device
- *
- * Match a PCI IDE port against an entry in ide_hwifs[],
- * based on io_base port if possible. Return the matching hwif,
- * or a new hwif. If we find an error (clashing, out of devices, etc)
- * return NULL
- *
- * FIXME: we need to handle mmio matches here too
- */
-
-static ide_hwif_t *ide_match_hwif(unsigned long io_base, u8 bootable, const char *name)
-{
- int h;
- ide_hwif_t *hwif;
-
- /*
- * Look for a hwif with matching io_base specified using
- * parameters to ide_setup().
- */
- for (h = 0; h < MAX_HWIFS; ++h) {
- hwif = &ide_hwifs[h];
- if (hwif->io_ports[IDE_DATA_OFFSET] == io_base) {
- if (hwif->chipset == ide_forced)
- return hwif; /* a perfect match */
- }
- }
- /*
- * Look for a hwif with matching io_base default value.
- * If chipset is "ide_unknown", then claim that hwif slot.
- * Otherwise, some other chipset has already claimed it.. :(
- */
- for (h = 0; h < MAX_HWIFS; ++h) {
- hwif = &ide_hwifs[h];
- if (hwif->io_ports[IDE_DATA_OFFSET] == io_base) {
- if (hwif->chipset == ide_unknown)
- return hwif; /* match */
- printk(KERN_ERR "%s: port 0x%04lx already claimed by %s\n",
- name, io_base, hwif->name);
- return NULL; /* already claimed */
- }
- }
- /*
- * Okay, there is no hwif matching our io_base,
- * so we'll just claim an unassigned slot.
- * Give preference to claiming other slots before claiming ide0/ide1,
- * just in case there's another interface yet-to-be-scanned
- * which uses ports 1f0/170 (the ide0/ide1 defaults).
- *
- * Unless there is a bootable card that does not use the standard
- * ports 1f0/170 (the ide0/ide1 defaults). The (bootable) flag.
- */
- if (bootable) {
- for (h = 0; h < MAX_HWIFS; ++h) {
- hwif = &ide_hwifs[h];
- if (hwif->chipset == ide_unknown)
- return hwif; /* pick an unused entry */
- }
- } else {
- for (h = 2; h < MAX_HWIFS; ++h) {
- hwif = ide_hwifs + h;
- if (hwif->chipset == ide_unknown)
- return hwif; /* pick an unused entry */
- }
- }
- for (h = 0; h < 2 && h < MAX_HWIFS; ++h) {
- hwif = ide_hwifs + h;
- if (hwif->chipset == ide_unknown)
- return hwif; /* pick an unused entry */
- }
- printk(KERN_ERR "%s: too many IDE interfaces, no room in table\n", name);
- return NULL;
-}
-
/**
* ide_setup_pci_baseregs - place a PCI IDE controller native
* @dev: PCI device of interface to switch native
*
* We attempt to place the PCI interface into PCI native mode. If
* we succeed the BARs are ok and the controller is in PCI mode.
- * Returns 0 on success or an errno code.
+ * Returns 0 on success or an errno code.
*
* FIXME: if we program the interface and then fail to set the BARS
* we don't switch it back to legacy mode. Do we actually care ??
*/
-
-static int ide_setup_pci_baseregs (struct pci_dev *dev, const char *name)
+
+static int ide_setup_pci_baseregs(struct pci_dev *dev, const char *name)
{
u8 progif = 0;
" PCI slot %s\n", d->name, dev->vendor, dev->device,
dev->revision, pci_name(dev));
}
-
EXPORT_SYMBOL_GPL(ide_setup_pci_noise);
* but if that fails then we only need IO space. The PCI code should
* have setup the proper resources for us already for controllers in
* legacy mode.
- *
+ *
* Returns zero on success or an error code
*/
* Maybe the user deliberately *disabled* the device,
* but we'll eventually ignore it again if no drives respond.
*/
- if (ide_setup_pci_baseregs(dev, d->name) || pci_write_config_word(dev, PCI_COMMAND, pcicmd|PCI_COMMAND_IO))
- {
+ if (ide_setup_pci_baseregs(dev, d->name) ||
+ pci_write_config_word(dev, PCI_COMMAND, pcicmd | PCI_COMMAND_IO)) {
printk(KERN_INFO "%s: device disabled (BIOS)\n", d->name);
return -ENODEV;
}
* @d: IDE port info
* @bar: BAR number
*
- * Checks if a BAR is configured and points to MMIO space. If so
- * print an error and return an error code. Otherwise return 0
+ * Checks if a BAR is configured and points to MMIO space. If so,
+ * return an error code. Otherwise return 0
*/
-static int ide_pci_check_iomem(struct pci_dev *dev, const struct ide_port_info *d, int bar)
+static int ide_pci_check_iomem(struct pci_dev *dev, const struct ide_port_info *d,
+ int bar)
{
ulong flags = pci_resource_flags(dev, bar);
-
+
/* Unconfigured ? */
if (!flags || pci_resource_len(dev, bar) == 0)
return 0;
- /* I/O space */
- if(flags & PCI_BASE_ADDRESS_IO_MASK)
+ /* I/O space */
+ if (flags & IORESOURCE_IO)
return 0;
-
+
/* Bad */
- printk(KERN_ERR "%s: IO baseregs (BIOS) are reported "
- "as MEM, report to "
- "<andre@linux-ide.org>.\n", d->name);
return -EINVAL;
}
{
unsigned long ctl = 0, base = 0;
ide_hwif_t *hwif;
- u8 bootable = (d->host_flags & IDE_HFLAG_BOOTABLE) ? 1 : 0;
- u8 oldnoprobe = 0;
struct hw_regs_s hw;
if ((d->host_flags & IDE_HFLAG_ISA_PORTS) == 0) {
- /* Possibly we should fail if these checks report true */
- ide_pci_check_iomem(dev, d, 2*port);
- ide_pci_check_iomem(dev, d, 2*port+1);
-
+ if (ide_pci_check_iomem(dev, d, 2 * port) ||
+ ide_pci_check_iomem(dev, d, 2 * port + 1)) {
+ printk(KERN_ERR "%s: I/O baseregs (BIOS) are reported "
+ "as MEM for port %d!\n", d->name, port);
+ return NULL;
+ }
+
ctl = pci_resource_start(dev, 2*port+1);
base = pci_resource_start(dev, 2*port);
if ((ctl && !base) || (base && !ctl)) {
return NULL;
}
}
- if (!ctl)
- {
+ if (!ctl) {
/* Use default values */
ctl = port ? 0x374 : 0x3f4;
base = port ? 0x170 : 0x1f0;
}
- if ((hwif = ide_match_hwif(base, bootable, d->name)) == NULL)
- return NULL; /* no room in ide_hwifs[] */
+
+ hwif = ide_find_port_slot(d);
+ if (hwif == NULL) {
+ printk(KERN_ERR "%s: too many IDE interfaces, no room in "
+ "table\n", d->name);
+ return NULL;
+ }
memset(&hw, 0, sizeof(hw));
- hw.irq = hwif->irq ? hwif->irq : irq;
+ hw.irq = irq;
hw.dev = &dev->dev;
hw.chipset = d->chipset ? d->chipset : ide_pci;
ide_std_init_ports(&hw, base, ctl | 2);
- if (hwif->io_ports[IDE_DATA_OFFSET] == base &&
- hwif->io_ports[IDE_CONTROL_OFFSET] == (ctl | 2))
- oldnoprobe = hwif->noprobe;
-
ide_init_port_hw(hwif, &hw);
- hwif->noprobe = oldnoprobe;
-
hwif->dev = &dev->dev;
hwif->cds = d;
unsigned long dma_base = ide_get_or_set_dma_base(d, hwif);
if (dma_base && !(pcicmd & PCI_COMMAND_MASTER)) {
/*
- * Set up BM-DMA capability
+ * Set up BM-DMA capability
* (PnP BIOS should have done this)
- */
+ */
pci_set_master(dev);
if (pci_read_config_word(dev, PCI_COMMAND, &pcicmd) || !(pcicmd & PCI_COMMAND_MASTER)) {
printk(KERN_ERR "%s: %s error updating PCICMD\n",
*(idx + port) = hwif->index;
}
}
-
EXPORT_SYMBOL_GPL(ide_pci_setup_ports);
/*
return ret;
}
-
EXPORT_SYMBOL_GPL(ide_setup_pci_device);
int ide_setup_pci_devices(struct pci_dev *dev1, struct pci_dev *dev2,
out:
return ret;
}
-
EXPORT_SYMBOL_GPL(ide_setup_pci_devices);
projects / linux-2.6 / blobdiff