#include <linux/types.h>
#include <linux/module.h>
#include <linux/pci.h>
-#include <linux/delay.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
-#include <asm/io.h>
+#define DRV_NAME "jmicron"
typedef enum {
PORT_PATA0 = 0,
} port_type;
/**
- * ata66_jmicron - Cable check
+ * jmicron_cable_detect - cable detection
* @hwif: IDE port
*
* Returns the cable type.
*/
-static u8 __devinit ata66_jmicron(ide_hwif_t *hwif)
+static u8 __devinit jmicron_cable_detect(ide_hwif_t *hwif)
{
- struct pci_dev *pdev = hwif->pci_dev;
+ struct pci_dev *pdev = to_pci_dev(hwif->dev);
u32 control;
u32 control5;
* actually do our cable checking etc. Thankfully we don't need
* to do the plumbing for other cases.
*/
- switch (port_map[port])
- {
+ switch (port_map[port]) {
case PORT_PATA0:
if (control & (1 << 3)) /* 40/80 pin primary */
return ATA_CBL_PATA40;
{
}
-/**
- * init_hwif_jmicron - set up hwif structs
- * @hwif: interface to set up
- *
- * Minimal set up is required for the Jmicron hardware.
- */
-
-static void __devinit init_hwif_jmicron(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &jmicron_set_pio_mode;
- hwif->set_dma_mode = &jmicron_set_dma_mode;
-
- if (hwif->dma_base == 0)
- return;
-
- if (hwif->cbl != ATA_CBL_PATA40_SHORT)
- hwif->cbl = ata66_jmicron(hwif);
-}
+static const struct ide_port_ops jmicron_port_ops = {
+ .set_pio_mode = jmicron_set_pio_mode,
+ .set_dma_mode = jmicron_set_dma_mode,
+ .cable_detect = jmicron_cable_detect,
+};
static const struct ide_port_info jmicron_chipset __devinitdata = {
- .name = "JMB",
- .init_hwif = init_hwif_jmicron,
- .host_flags = IDE_HFLAG_BOOTABLE,
+ .name = DRV_NAME,
.enablebits = { { 0x40, 0x01, 0x01 }, { 0x40, 0x10, 0x10 } },
+ .port_ops = &jmicron_port_ops,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
static int __devinit jmicron_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- ide_setup_pci_device(dev, &jmicron_chipset);
- return 0;
+ return ide_pci_init_one(dev, &jmicron_chipset, NULL);
}
/* All JMB PATA controllers have and will continue to have the same
.name = "JMicron IDE",
.id_table = jmicron_pci_tbl,
.probe = jmicron_init_one,
+ .remove = ide_pci_remove,
};
static int __init jmicron_ide_init(void)
return ide_pci_register_driver(&driver);
}
+static void __exit jmicron_ide_exit(void)
+{
+ pci_unregister_driver(&driver);
+}
+
module_init(jmicron_ide_init);
+module_exit(jmicron_ide_exit);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("PCI driver module for the JMicron in legacy modes");