if IDE
-config IDE_MAX_HWIFS
+config IDE_MAX_HWIFS
int "Max IDE interfaces"
- depends on ALPHA || SUPERH
+ depends on ALPHA || SUPERH || IA64
default 4
help
This is the maximum number of IDE hardware interfaces that will
tristate "PCMCIA IDE support"
depends on PCMCIA
help
- Support for outboard IDE disks, tape drives, and CD-ROM drives
- connected through a PCMCIA card.
+ Support for Compact Flash cards, outboard IDE disks, tape drives,
+ and CD-ROM drives connected through a PCMCIA card.
config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
help
This is a direct raw access to the media. It is a complex but
elegant solution to test and validate the domain of the hardware and
- perform below the driver data recover if needed. This is the most
+ perform below the driver data recovery if needed. This is the most
basic form of media-forensics.
If you are unsure, say N here.
tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
depends on EXPERIMENTAL
help
- Include support for PIO tuning an virtual DMA on the Cyrix MediaGX
+ Include support for PIO tuning and virtual DMA on the Cyrix MediaGX
5510/5520 chipset. This will automatically be detected and
configured if found.
It is safe to say Y to this question.
+config BLK_DEV_CS5535
+ tristate "AMD CS5535 chipset support"
+ depends on X86 && !X86_64
+ help
+ Include support for UDMA on the NSC/AMD CS5535 companion chipset.
+ This will automatically be detected and configured if found.
+
+ It is safe to say Y to this question.
+
config BLK_DEV_HPT34X
tristate "HPT34X chipset support"
help
tristate "NS87415 chipset support"
help
This driver adds detection and support for the NS87415 chip
- (used in SPARC64, among others).
+ (used mainly on SPARC64 and PA-RISC machines).
Please read the comments at the top of <file:drivers/ide/pci/ns87415.c>.
It was originally designed for the PDC20246/Ultra33, whose BIOS will
only setup UDMA on the first two PDC20246 cards. It has also been
- used succesfully on a PDC20265/Ultra100, allowing use of UDMA modes
+ used successfully on a PDC20265/Ultra100, allowing use of UDMA modes
when the PDC20265 BIOS has been disabled (for faster boot up).
Please read the comments at the top of
config BLK_DEV_PDC202XX_NEW
tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
-# FIXME - probably wants to be one for old and for new
-config PDC202XX_FORCE
- bool "Enable controller even if disabled by BIOS"
- depends on BLK_DEV_PDC202XX_NEW
- help
- Enable the PDC202xx controller even if it has been disabled in the BIOS setup.
-
config BLK_DEV_SVWKS
tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
help
config BLK_DEV_SLC90E66
tristate "SLC90E66 chipset support"
help
- This driver ensures (U)DMA support for Victroy66 SouthBridges for
+ This driver ensures (U)DMA support for Victory66 SouthBridges for
SMsC with Intel NorthBridges. This is an Ultra66 based chipset.
The nice thing about it is that you can mix Ultra/DMA/PIO devices
and it will handle timing cycles. Since this is an improved
performance.
config BLK_DEV_IDE_PMAC_BLINK
- bool "Blink laptop LED on drive activity"
+ bool "Blink laptop LED on drive activity (DEPRECATED)"
depends on BLK_DEV_IDE_PMAC && ADB_PMU
+ select ADB_PMU_LED
+ select LEDS_TRIGGERS
+ select LEDS_TRIGGER_IDE_DISK
help
This option enables the use of the sleep LED as a hard drive
activity LED.
+ This option is deprecated, it only selects ADB_PMU_LED and
+ LEDS_TRIGGER_IDE_DISK and changes the code in the new led class
+ device to default to the ide-disk trigger (which should be set
+ from userspace via sysfs).
+
+config BLK_DEV_IDE_SWARM
+ tristate "IDE for Sibyte evaluation boards"
+ depends on SIBYTE_SB1xxx_SOC
config BLK_DEV_IDE_AU1XXX
bool "IDE for AMD Alchemy Au1200"
depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
endchoice
-config BLK_DEV_IDE_AU1XXX_BURSTABLE_ON
- bool "Enable burstable Mode on DbDMA"
- default false
- depends BLK_DEV_IDE_AU1XXX
- help
- This option enable the burstable Flag on DbDMA controller
- (cf. "AMD Alchemy 'Au1200' Processor Data Book - PRELIMINARY").
-
config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
int "Maximum transfer size (KB) per request (up to 128)"
default "128"
config BLK_DEV_MPC8xx_IDE
bool "MPC8xx IDE support"
- depends on 8xx
+ depends on 8xx && IDE=y && BLK_DEV_IDE=y
help
This option provides support for IDE on Motorola MPC8xx Systems.
Please see 'Type of MPC8xx IDE interface' for details.
in that mode with an 80c ribbon.
If you are experiencing compatibility or performance problems, you
- MAY try to answering Y here. However, it does not necessarily solve
+ MAY try to answer Y here. However, it does not necessarily solve
any of your problems, it could even cause more of them.
It is normally safe to answer Y; however, the default is N.