if IDE
-config IDE_MAX_HWIFS
+config IDE_MAX_HWIFS
int "Max IDE interfaces"
- depends on ALPHA || SUPERH
+ depends on ALPHA || SUPERH || IA64
default 4
help
This is the maximum number of IDE hardware interfaces that will
tristate "PCMCIA IDE support"
depends on PCMCIA
help
- Support for outboard IDE disks, tape drives, and CD-ROM drives
- connected through a PCMCIA card.
+ Support for Compact Flash cards, outboard IDE disks, tape drives,
+ and CD-ROM drives connected through a PCMCIA card.
config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
help
This is a direct raw access to the media. It is a complex but
elegant solution to test and validate the domain of the hardware and
- perform below the driver data recover if needed. This is the most
+ perform below the driver data recovery if needed. This is the most
basic form of media-forensics.
If you are unsure, say N here.
tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
depends on EXPERIMENTAL
help
- Include support for PIO tuning an virtual DMA on the Cyrix MediaGX
+ Include support for PIO tuning and virtual DMA on the Cyrix MediaGX
5510/5520 chipset. This will automatically be detected and
configured if found.
It is safe to say Y to this question.
+config BLK_DEV_CS5535
+ tristate "AMD CS5535 chipset support"
+ depends on X86 && !X86_64
+ help
+ Include support for UDMA on the NSC/AMD CS5535 companion chipset.
+ This will automatically be detected and configured if found.
+
+ It is safe to say Y to this question.
+
config BLK_DEV_HPT34X
tristate "HPT34X chipset support"
help
tristate "NS87415 chipset support"
help
This driver adds detection and support for the NS87415 chip
- (used in SPARC64, among others).
+ (used mainly on SPARC64 and PA-RISC machines).
Please read the comments at the top of <file:drivers/ide/pci/ns87415.c>.
It was originally designed for the PDC20246/Ultra33, whose BIOS will
only setup UDMA on the first two PDC20246 cards. It has also been
- used succesfully on a PDC20265/Ultra100, allowing use of UDMA modes
+ used successfully on a PDC20265/Ultra100, allowing use of UDMA modes
when the PDC20265 BIOS has been disabled (for faster boot up).
Please read the comments at the top of
config BLK_DEV_PDC202XX_NEW
tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
-# FIXME - probably wants to be one for old and for new
-config PDC202XX_FORCE
- bool "Enable controller even if disabled by BIOS"
- depends on BLK_DEV_PDC202XX_NEW
- help
- Enable the PDC202xx controller even if it has been disabled in the BIOS setup.
-
config BLK_DEV_SVWKS
tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
help
config BLK_DEV_SLC90E66
tristate "SLC90E66 chipset support"
help
- This driver ensures (U)DMA support for Victroy66 SouthBridges for
+ This driver ensures (U)DMA support for Victory66 SouthBridges for
SMsC with Intel NorthBridges. This is an Ultra66 based chipset.
The nice thing about it is that you can mix Ultra/DMA/PIO devices
and it will handle timing cycles. Since this is an improved
performance.
config BLK_DEV_IDE_PMAC_BLINK
- bool "Blink laptop LED on drive activity"
+ bool "Blink laptop LED on drive activity (DEPRECATED)"
depends on BLK_DEV_IDE_PMAC && ADB_PMU
+ select ADB_PMU_LED
+ select LEDS_TRIGGERS
+ select LEDS_TRIGGER_IDE_DISK
help
This option enables the use of the sleep LED as a hard drive
activity LED.
+ This option is deprecated, it only selects ADB_PMU_LED and
+ LEDS_TRIGGER_IDE_DISK and changes the code in the new led class
+ device to default to the ide-disk trigger (which should be set
+ from userspace via sysfs).
+
+config BLK_DEV_IDE_SWARM
+ tristate "IDE for Sibyte evaluation boards"
+ depends on SIBYTE_SB1xxx_SOC
+
+config BLK_DEV_IDE_AU1XXX
+ bool "IDE for AMD Alchemy Au1200"
+ depends on SOC_AU1200
+choice
+ prompt "IDE Mode for AMD Alchemy Au1200"
+ default CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA
+ depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
+
+config BLK_DEV_IDE_AU1XXX_PIO_DBDMA
+ bool "PIO+DbDMA IDE for AMD Alchemy Au1200"
+
+config BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
+ bool "MDMA2+DbDMA IDE for AMD Alchemy Au1200"
+ depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
+endchoice
+
+config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
+ int "Maximum transfer size (KB) per request (up to 128)"
+ default "128"
+ depends BLK_DEV_IDE_AU1XXX
config IDE_ARM
def_bool ARM && (ARCH_A5K || ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
config BLK_DEV_MPC8xx_IDE
bool "MPC8xx IDE support"
- depends on 8xx
+ depends on 8xx && IDE=y && BLK_DEV_IDE=y
help
This option provides support for IDE on Motorola MPC8xx Systems.
Please see 'Type of MPC8xx IDE interface' for details.
endif
config BLK_DEV_IDEDMA
- def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
+ def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
config IDEDMA_IVB
bool "IGNORE word93 Validation BITS"
in that mode with an 80c ribbon.
If you are experiencing compatibility or performance problems, you
- MAY try to answering Y here. However, it does not necessarily solve
+ MAY try to answer Y here. However, it does not necessarily solve
any of your problems, it could even cause more of them.
It is normally safe to answer Y; however, the default is N.