usb ethernet gadget, workaround network stack API glitch

[linux-2.6] / drivers / ide / Kconfig

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 3f76987d818af376d9912f0614b00d6e797c190a..5bdf64b779134d555508891dbe49e7a55651f904 100644 (file)
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -57,6 +57,7 @@ if IDE
 config IDE_MAX_HWIFS
        int "Max IDE interfaces"
        depends on ALPHA || SUPERH || IA64 || EMBEDDED
+       range 1 10
        default 4
        help
          This is the maximum number of IDE hardware interfaces that will
@@ -103,8 +104,10 @@ config BLK_DEV_IDE_SATA
        ---help---
          There are two drivers for Serial ATA controllers.
 
-         The main driver, "libata", exists inside the SCSI subsystem
-         and supports most modern SATA controllers.
+         The main driver, "libata", uses the SCSI subsystem
+         and supports most modern SATA controllers. In order to use it
+         you may take a look at "Serial ATA (prod) and Parallel ATA
+         (experimental) drivers".
 
          The IDE driver (which you are currently configuring) supports
          a few first-generation SATA controllers.
@@ -434,24 +437,8 @@ config BLK_DEV_IDEDMA_FORCED
 
          Generally say N here.
 
-config IDEDMA_PCI_AUTO
-       bool "Use PCI DMA by default when available"
-       ---help---
-         Prior to kernel version 2.1.112, Linux used to automatically use
-         DMA for IDE drives and chipsets which support it. Due to concerns
-         about a couple of cases where buggy hardware may have caused damage,
-         the default is now to NOT use DMA automatically. To revert to the
-         previous behaviour, say Y to this question.
-
-         If you suspect your hardware is at all flakey, say N here.
-         Do NOT email the IDE kernel people regarding this issue!
-
-         It is normally safe to answer Y to this question unless your
-         motherboard uses a VIA VP2 chipset, in which case you should say N.
-
 config IDEDMA_ONLYDISK
        bool "Enable DMA only for disks "
-       depends on IDEDMA_PCI_AUTO
        help
          This is used if you know your ATAPI Devices are going to fail DMA
          Transfers.
@@ -769,6 +756,14 @@ config BLK_DEV_TC86C001
        help
        This driver adds support for Toshiba TC86C001 GOKU-S chip.
 
+config BLK_DEV_CELLEB
+       tristate "Toshiba's Cell Reference Set IDE support"
+       depends on PPC_CELLEB
+       help
+         This driver provides support for the built-in IDE controller on
+         Toshiba Cell Reference Board.
+         If unsure, say Y.
+
 endif
 
 config BLK_DEV_IDE_PMAC
@@ -800,14 +795,6 @@ config BLK_DEV_IDEDMA_PMAC
          to transfer data to and from memory.  Saying Y is safe and improves
          performance.
 
-config BLK_DEV_IDE_CELLEB
-       bool "Toshiba's Cell Reference Set IDE support"
-       depends on PPC_CELLEB && IDE=y
-       help
-         This driver provides support for the built-in IDE controller on
-         Toshiba Cell Reference Board.
-         If unsure, say Y.
-
 config BLK_DEV_IDE_SWARM
        tristate "IDE for Sibyte evaluation boards"
        depends on SIBYTE_SB1xxx_SOC
@@ -851,19 +838,6 @@ config BLK_DEV_IDEDMA_ICS
          Say Y here if you want to add DMA (Direct Memory Access) support to
          the ICS IDE driver.
 
-config IDEDMA_ICS_AUTO
-       bool "Use ICS DMA by default"
-       depends on BLK_DEV_IDEDMA_ICS
-       help
-         Prior to kernel version 2.1.112, Linux used to automatically use
-         DMA for IDE drives and chipsets which support it. Due to concerns
-         about a couple of cases where buggy hardware may have caused damage,
-         the default is now to NOT use DMA automatically. To revert to the
-         previous behaviour, say Y to this question.
-
-         If you suspect your hardware is at all flakey, say N here.
-         Do NOT email the IDE kernel people regarding this issue!
-
 config BLK_DEV_IDE_RAPIDE
        tristate "RapIDE interface support"
        depends on ARM && ARCH_ACORN
@@ -1086,9 +1060,6 @@ config IDEDMA_IVB
 
          It is normally safe to answer Y; however, the default is N.
 
-config IDEDMA_AUTO
-       def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO
-
 endif
 
 config BLK_DEV_HD_ONLY