#include "edac_mc.h"
+#define r82600_printk(level, fmt, arg...) \
+ edac_printk(level, "r82600", fmt, ##arg)
+
+#define r82600_mc_printk(mci, level, fmt, arg...) \
+ edac_mc_chipset_printk(mci, level, "r82600", fmt, ##arg)
+
/* Radisys say "The 82600 integrates a main memory SDRAM controller that
* supports up to four banks of memory. The four banks can support a mix of
* sizes of 64 bit wide (72 bits with ECC) Synchronous DRAM (SDRAM) DIMMs,
{
struct r82600_error_info info;
- debugf1("MC%d: " __FILE__ ": %s()\n", mci->mc_idx, __func__);
+ debugf1("MC%d: %s()\n", mci->mc_idx, __func__);
r82600_get_error_info(mci, &info);
r82600_process_error_info(mci, &info, 1);
}
u32 scrub_disabled;
u32 sdram_refresh_rate;
u32 row_high_limit_last = 0;
- u32 eap_init_bits;
+ struct r82600_error_info discard;
- debugf0("MC: " __FILE__ ": %s()\n", __func__);
+ debugf0("%s()\n", __func__);
pci_read_config_byte(pdev, R82600_DRAMC, &dramcr);
scrub_disabled = eapr & BIT(31);
sdram_refresh_rate = dramcr & (BIT(0) | BIT(1));
- debugf2("MC: " __FILE__ ": %s(): sdram refresh rate = %#0x\n",
- __func__, sdram_refresh_rate);
+ debugf2("%s(): sdram refresh rate = %#0x\n", __func__,
+ sdram_refresh_rate);
- debugf2("MC: " __FILE__ ": %s(): DRAMC register = %#0x\n", __func__,
- dramcr);
+ debugf2("%s(): DRAMC register = %#0x\n", __func__, dramcr);
mci = edac_mc_alloc(0, R82600_NR_CSROWS, R82600_NR_CHANS);
goto fail;
}
- debugf0("MC: " __FILE__ ": %s(): mci = %p\n", __func__, mci);
+ debugf0("%s(): mci = %p\n", __func__, mci);
mci->pdev = pdev;
mci->mtype_cap = MEM_FLAG_RDDR | MEM_FLAG_DDR;
mci->edac_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
if (ecc_on) {
if (scrub_disabled)
- debugf3("MC: " __FILE__ ": %s(): mci = %p - "
- "Scrubbing disabled! EAP: %#0x\n", __func__,
- mci, eapr);
+ debugf3("%s(): mci = %p - Scrubbing disabled! EAP: "
+ "%#0x\n", __func__, mci, eapr);
} else
mci->edac_cap = EDAC_FLAG_NONE;
- mci->mod_name = BS_MOD_STR;
+ mci->mod_name = EDAC_MOD_STR;
mci->mod_ver = "$Revision: 1.1.2.6 $";
mci->ctl_name = "R82600";
mci->edac_check = r82600_check;
/* find the DRAM Chip Select Base address and mask */
pci_read_config_byte(mci->pdev, R82600_DRBA + index, &drbar);
- debugf1("MC%d: " __FILE__ ": %s() Row=%d DRBA = %#0x\n",
- mci->mc_idx, __func__, index, drbar);
+ debugf1("MC%d: %s() Row=%d DRBA = %#0x\n", mci->mc_idx,
+ __func__, index, drbar);
row_high_limit = ((u32) drbar << 24);
/* row_high_limit = ((u32)drbar << 24) | 0xffffffUL; */
- debugf1("MC%d: " __FILE__ ": %s() Row=%d, "
- "Boundry Address=%#0x, Last = %#0x \n",
- mci->mc_idx, __func__, index, row_high_limit,
- row_high_limit_last);
+ debugf1("MC%d: %s() Row=%d, Boundry Address=%#0x, Last = "
+ "%#0x \n", mci->mc_idx, __func__, index,
+ row_high_limit, row_high_limit_last);
/* Empty row [p.57] */
if (row_high_limit == row_high_limit_last)
row_high_limit_last = row_high_limit;
}
- /* clear counters */
- /* FIXME should we? */
+ r82600_get_error_info(mci, &discard); /* clear counters */
if (edac_mc_add_mc(mci)) {
- debugf3("MC: " __FILE__
- ": %s(): failed edac_mc_add_mc()\n", __func__);
+ debugf3("%s(): failed edac_mc_add_mc()\n", __func__);
goto fail;
}
/* get this far and it's successful */
- /* Clear error flags to allow next error to be reported [p.62] */
- /* Test systems seem to always have the UE flag raised on boot */
-
- eap_init_bits = BIT(0) & BIT(1);
if (disable_hardware_scrub) {
- eap_init_bits |= BIT(31);
- debugf3("MC: " __FILE__ ": %s(): Disabling Hardware Scrub "
- "(scrub on error)\n", __func__);
+ debugf3("%s(): Disabling Hardware Scrub (scrub on error)\n",
+ __func__);
+ pci_write_bits32(mci->pdev, R82600_EAP, BIT(31), BIT(31));
}
- pci_write_bits32(mci->pdev, R82600_EAP, eap_init_bits,
- eap_init_bits);
-
- debugf3("MC: " __FILE__ ": %s(): success\n", __func__);
+ debugf3("%s(): success\n", __func__);
return 0;
fail:
static int __devinit r82600_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
- debugf0("MC: " __FILE__ ": %s()\n", __func__);
+ debugf0("%s()\n", __func__);
/* don't need to call pci_device_enable() */
return r82600_probe1(pdev, ent->driver_data);
{
struct mem_ctl_info *mci;
- debugf0(__FILE__ ": %s()\n", __func__);
+ debugf0("%s()\n", __func__);
if (((mci = edac_mc_find_mci_by_pdev(pdev)) != NULL) &&
!edac_mc_del_mc(mci))
static struct pci_driver r82600_driver = {
- .name = BS_MOD_STR,
+ .name = EDAC_MOD_STR,
.probe = r82600_init_one,
.remove = __devexit_p(r82600_remove_one),
.id_table = r82600_pci_tbl,