#include <linux/smp_lock.h>
#include <linux/device.h>
#include <linux/delay.h>
+#include <linux/ctype.h>
#include <asm/io.h>
#include <asm/uaccess.h>
-#ifdef CONFIG_PCI
#include <linux/pci.h>
-#endif
/*****************************************************************************/
#define BRD_ECH64PCI 27
#define BRD_EASYIOPCI 28
-/*
- * Define a configuration structure to hold the board configuration.
- * Need to set this up in the code (for now) with the boards that are
- * to be configured into the system. This is what needs to be modified
- * when adding/removing/modifying boards. Each line entry in the
- * stl_brdconf[] array is a board. Each line contains io/irq/memory
- * ranges for that board (as well as what type of board it is).
- * Some examples:
- * { BRD_EASYIO, 0x2a0, 0, 0, 10, 0 },
- * This line would configure an EasyIO board (4 or 8, no difference),
- * at io address 2a0 and irq 10.
- * Another example:
- * { BRD_ECH, 0x2a8, 0x280, 0, 12, 0 },
- * This line will configure an EasyConnection 8/32 board at primary io
- * address 2a8, secondary io address 280 and irq 12.
- * Enter as many lines into this array as you want (only the first 4
- * will actually be used!). Any combination of EasyIO and EasyConnection
- * boards can be specified. EasyConnection 8/32 boards can share their
- * secondary io addresses between each other.
- *
- * NOTE: there is no need to put any entries in this table for PCI
- * boards. They will be found automatically by the driver - provided
- * PCI BIOS32 support is compiled into the kernel.
- */
-
-typedef struct {
- int brdtype;
+struct stlconf {
+ unsigned int brdtype;
int ioaddr1;
int ioaddr2;
unsigned long memaddr;
int irq;
int irqtype;
-} stlconf_t;
-
-static stlconf_t stl_brdconf[] = {
- /*{ BRD_EASYIO, 0x2a0, 0, 0, 10, 0 },*/
};
-static int stl_nrbrds = ARRAY_SIZE(stl_brdconf);
+static unsigned int stl_nrbrds;
/*****************************************************************************/
* with this termios initially. Basically all it defines is a raw port
* at 9600, 8 data bits, 1 stop bit.
*/
-static struct termios stl_deftermios = {
+static struct ktermios stl_deftermios = {
.c_cflag = (B9600 | CS8 | CREAD | HUPCL | CLOCAL),
.c_cc = INIT_C_CC,
+ .c_ispeed = 9600,
+ .c_ospeed = 9600,
};
-/*
- * Define global stats structures. Not used often, and can be
- * re-used for each stats call.
- */
-static comstats_t stl_comstats;
-static combrd_t stl_brdstats;
-static stlbrd_t stl_dummybrd;
-static stlport_t stl_dummyport;
-
/*
* Define global place to put buffer overflow characters.
*/
/*****************************************************************************/
-static stlbrd_t *stl_brds[STL_MAXBRDS];
+static DEFINE_MUTEX(stl_brdslock);
+static struct stlbrd *stl_brds[STL_MAXBRDS];
/*
* Per board state flags. Used with the state field of the board struct.
* Not really much here!
*/
#define BRD_FOUND 0x1
+#define STL_PROBED 0x2
+
/*
* Define the port structure istate flags. These set of flags are
* load line. These allow for easy board definitions, and easy
* modification of the io, memory and irq resoucres.
*/
-static int stl_nargs = 0;
+static unsigned int stl_nargs;
static char *board0[4];
static char *board1[4];
static char *board2[4];
* parse any module arguments.
*/
-typedef struct stlbrdtype {
+static struct {
char *name;
int type;
-} stlbrdtype_t;
-
-static stlbrdtype_t stl_brdstr[] = {
+} stl_brdstr[] = {
{ "easyio", BRD_EASYIO },
{ "eio", BRD_EASYIO },
{ "20", BRD_EASYIO },
/*
* Define the module agruments.
*/
-MODULE_AUTHOR("Greg Ungerer");
-MODULE_DESCRIPTION("Stallion Multiport Serial Driver");
-MODULE_LICENSE("GPL");
module_param_array(board0, charp, &stl_nargs, 0);
MODULE_PARM_DESC(board0, "Board 0 config -> name[,ioaddr[,ioaddr2][,irq]]");
/*****************************************************************************/
-#ifdef CONFIG_PCI
-
/*
* Define the Stallion PCI vendor and device IDs.
*/
/*
* Define structure to hold all Stallion PCI boards.
*/
-typedef struct stlpcibrd {
- unsigned short vendid;
- unsigned short devid;
- int brdtype;
-} stlpcibrd_t;
-
-static stlpcibrd_t stl_pcibrds[] = {
- { PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_ECHPCI864, BRD_ECH64PCI },
- { PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_EIOPCI, BRD_EASYIOPCI },
- { PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_ECHPCI832, BRD_ECHPCI },
- { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410, BRD_ECHPCI },
-};
-static int stl_nrpcibrds = ARRAY_SIZE(stl_pcibrds);
-
-#endif
+static struct pci_device_id stl_pcibrds[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_ECHPCI864),
+ .driver_data = BRD_ECH64PCI },
+ { PCI_DEVICE(PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_EIOPCI),
+ .driver_data = BRD_EASYIOPCI },
+ { PCI_DEVICE(PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_ECHPCI832),
+ .driver_data = BRD_ECHPCI },
+ { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410),
+ .driver_data = BRD_ECHPCI },
+ { }
+};
+MODULE_DEVICE_TABLE(pci, stl_pcibrds);
/*****************************************************************************/
9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600
};
-/*
- * Define some handy local macros...
- */
-#undef MIN
-#define MIN(a,b) (((a) <= (b)) ? (a) : (b))
-
-#undef TOLOWER
-#define TOLOWER(x) ((((x) >= 'A') && ((x) <= 'Z')) ? ((x) + 0x20) : (x))
-
/*****************************************************************************/
/*
* Declare all those functions in this driver!
*/
-static void stl_argbrds(void);
-static int stl_parsebrd(stlconf_t *confp, char **argp);
-
-static unsigned long stl_atol(char *str);
-
-static int stl_init(void);
-static int stl_open(struct tty_struct *tty, struct file *filp);
-static void stl_close(struct tty_struct *tty, struct file *filp);
-static int stl_write(struct tty_struct *tty, const unsigned char *buf, int count);
-static void stl_putchar(struct tty_struct *tty, unsigned char ch);
-static void stl_flushchars(struct tty_struct *tty);
-static int stl_writeroom(struct tty_struct *tty);
-static int stl_charsinbuffer(struct tty_struct *tty);
-static int stl_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
-static void stl_settermios(struct tty_struct *tty, struct termios *old);
-static void stl_throttle(struct tty_struct *tty);
-static void stl_unthrottle(struct tty_struct *tty);
-static void stl_stop(struct tty_struct *tty);
-static void stl_start(struct tty_struct *tty);
-static void stl_flushbuffer(struct tty_struct *tty);
-static void stl_breakctl(struct tty_struct *tty, int state);
-static void stl_waituntilsent(struct tty_struct *tty, int timeout);
-static void stl_sendxchar(struct tty_struct *tty, char ch);
-static void stl_hangup(struct tty_struct *tty);
static int stl_memioctl(struct inode *ip, struct file *fp, unsigned int cmd, unsigned long arg);
-static int stl_portinfo(stlport_t *portp, int portnr, char *pos);
-static int stl_readproc(char *page, char **start, off_t off, int count, int *eof, void *data);
-
-static int stl_brdinit(stlbrd_t *brdp);
-static int stl_initports(stlbrd_t *brdp, stlpanel_t *panelp);
-static int stl_getserial(stlport_t *portp, struct serial_struct __user *sp);
-static int stl_setserial(stlport_t *portp, struct serial_struct __user *sp);
-static int stl_getbrdstats(combrd_t __user *bp);
-static int stl_getportstats(stlport_t *portp, comstats_t __user *cp);
-static int stl_clrportstats(stlport_t *portp, comstats_t __user *cp);
-static int stl_getportstruct(stlport_t __user *arg);
-static int stl_getbrdstruct(stlbrd_t __user *arg);
-static int stl_waitcarrier(stlport_t *portp, struct file *filp);
-static int stl_eiointr(stlbrd_t *brdp);
-static int stl_echatintr(stlbrd_t *brdp);
-static int stl_echmcaintr(stlbrd_t *brdp);
-static int stl_echpciintr(stlbrd_t *brdp);
-static int stl_echpci64intr(stlbrd_t *brdp);
-static void stl_offintr(struct work_struct *);
-static stlbrd_t *stl_allocbrd(void);
-static stlport_t *stl_getport(int brdnr, int panelnr, int portnr);
-
-static inline int stl_initbrds(void);
-static inline int stl_initeio(stlbrd_t *brdp);
-static inline int stl_initech(stlbrd_t *brdp);
-static inline int stl_getbrdnr(void);
-
-#ifdef CONFIG_PCI
-static inline int stl_findpcibrds(void);
-static inline int stl_initpcibrd(int brdtype, struct pci_dev *devp);
-#endif
+static int stl_brdinit(struct stlbrd *brdp);
+static int stl_getportstats(struct stlport *portp, comstats_t __user *cp);
+static int stl_clrportstats(struct stlport *portp, comstats_t __user *cp);
+static int stl_waitcarrier(struct stlport *portp, struct file *filp);
/*
* CD1400 uart specific handling functions.
*/
-static void stl_cd1400setreg(stlport_t *portp, int regnr, int value);
-static int stl_cd1400getreg(stlport_t *portp, int regnr);
-static int stl_cd1400updatereg(stlport_t *portp, int regnr, int value);
-static int stl_cd1400panelinit(stlbrd_t *brdp, stlpanel_t *panelp);
-static void stl_cd1400portinit(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp);
-static void stl_cd1400setport(stlport_t *portp, struct termios *tiosp);
-static int stl_cd1400getsignals(stlport_t *portp);
-static void stl_cd1400setsignals(stlport_t *portp, int dtr, int rts);
-static void stl_cd1400ccrwait(stlport_t *portp);
-static void stl_cd1400enablerxtx(stlport_t *portp, int rx, int tx);
-static void stl_cd1400startrxtx(stlport_t *portp, int rx, int tx);
-static void stl_cd1400disableintrs(stlport_t *portp);
-static void stl_cd1400sendbreak(stlport_t *portp, int len);
-static void stl_cd1400flowctrl(stlport_t *portp, int state);
-static void stl_cd1400sendflow(stlport_t *portp, int state);
-static void stl_cd1400flush(stlport_t *portp);
-static int stl_cd1400datastate(stlport_t *portp);
-static void stl_cd1400eiointr(stlpanel_t *panelp, unsigned int iobase);
-static void stl_cd1400echintr(stlpanel_t *panelp, unsigned int iobase);
-static void stl_cd1400txisr(stlpanel_t *panelp, int ioaddr);
-static void stl_cd1400rxisr(stlpanel_t *panelp, int ioaddr);
-static void stl_cd1400mdmisr(stlpanel_t *panelp, int ioaddr);
-
-static inline int stl_cd1400breakisr(stlport_t *portp, int ioaddr);
+static void stl_cd1400setreg(struct stlport *portp, int regnr, int value);
+static int stl_cd1400getreg(struct stlport *portp, int regnr);
+static int stl_cd1400updatereg(struct stlport *portp, int regnr, int value);
+static int stl_cd1400panelinit(struct stlbrd *brdp, struct stlpanel *panelp);
+static void stl_cd1400portinit(struct stlbrd *brdp, struct stlpanel *panelp, struct stlport *portp);
+static void stl_cd1400setport(struct stlport *portp, struct ktermios *tiosp);
+static int stl_cd1400getsignals(struct stlport *portp);
+static void stl_cd1400setsignals(struct stlport *portp, int dtr, int rts);
+static void stl_cd1400ccrwait(struct stlport *portp);
+static void stl_cd1400enablerxtx(struct stlport *portp, int rx, int tx);
+static void stl_cd1400startrxtx(struct stlport *portp, int rx, int tx);
+static void stl_cd1400disableintrs(struct stlport *portp);
+static void stl_cd1400sendbreak(struct stlport *portp, int len);
+static void stl_cd1400flowctrl(struct stlport *portp, int state);
+static void stl_cd1400sendflow(struct stlport *portp, int state);
+static void stl_cd1400flush(struct stlport *portp);
+static int stl_cd1400datastate(struct stlport *portp);
+static void stl_cd1400eiointr(struct stlpanel *panelp, unsigned int iobase);
+static void stl_cd1400echintr(struct stlpanel *panelp, unsigned int iobase);
+static void stl_cd1400txisr(struct stlpanel *panelp, int ioaddr);
+static void stl_cd1400rxisr(struct stlpanel *panelp, int ioaddr);
+static void stl_cd1400mdmisr(struct stlpanel *panelp, int ioaddr);
+
+static inline int stl_cd1400breakisr(struct stlport *portp, int ioaddr);
/*
* SC26198 uart specific handling functions.
*/
-static void stl_sc26198setreg(stlport_t *portp, int regnr, int value);
-static int stl_sc26198getreg(stlport_t *portp, int regnr);
-static int stl_sc26198updatereg(stlport_t *portp, int regnr, int value);
-static int stl_sc26198getglobreg(stlport_t *portp, int regnr);
-static int stl_sc26198panelinit(stlbrd_t *brdp, stlpanel_t *panelp);
-static void stl_sc26198portinit(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp);
-static void stl_sc26198setport(stlport_t *portp, struct termios *tiosp);
-static int stl_sc26198getsignals(stlport_t *portp);
-static void stl_sc26198setsignals(stlport_t *portp, int dtr, int rts);
-static void stl_sc26198enablerxtx(stlport_t *portp, int rx, int tx);
-static void stl_sc26198startrxtx(stlport_t *portp, int rx, int tx);
-static void stl_sc26198disableintrs(stlport_t *portp);
-static void stl_sc26198sendbreak(stlport_t *portp, int len);
-static void stl_sc26198flowctrl(stlport_t *portp, int state);
-static void stl_sc26198sendflow(stlport_t *portp, int state);
-static void stl_sc26198flush(stlport_t *portp);
-static int stl_sc26198datastate(stlport_t *portp);
-static void stl_sc26198wait(stlport_t *portp);
-static void stl_sc26198txunflow(stlport_t *portp, struct tty_struct *tty);
-static void stl_sc26198intr(stlpanel_t *panelp, unsigned int iobase);
-static void stl_sc26198txisr(stlport_t *port);
-static void stl_sc26198rxisr(stlport_t *port, unsigned int iack);
-static void stl_sc26198rxbadch(stlport_t *portp, unsigned char status, char ch);
-static void stl_sc26198rxbadchars(stlport_t *portp);
-static void stl_sc26198otherisr(stlport_t *port, unsigned int iack);
+static void stl_sc26198setreg(struct stlport *portp, int regnr, int value);
+static int stl_sc26198getreg(struct stlport *portp, int regnr);
+static int stl_sc26198updatereg(struct stlport *portp, int regnr, int value);
+static int stl_sc26198getglobreg(struct stlport *portp, int regnr);
+static int stl_sc26198panelinit(struct stlbrd *brdp, struct stlpanel *panelp);
+static void stl_sc26198portinit(struct stlbrd *brdp, struct stlpanel *panelp, struct stlport *portp);
+static void stl_sc26198setport(struct stlport *portp, struct ktermios *tiosp);
+static int stl_sc26198getsignals(struct stlport *portp);
+static void stl_sc26198setsignals(struct stlport *portp, int dtr, int rts);
+static void stl_sc26198enablerxtx(struct stlport *portp, int rx, int tx);
+static void stl_sc26198startrxtx(struct stlport *portp, int rx, int tx);
+static void stl_sc26198disableintrs(struct stlport *portp);
+static void stl_sc26198sendbreak(struct stlport *portp, int len);
+static void stl_sc26198flowctrl(struct stlport *portp, int state);
+static void stl_sc26198sendflow(struct stlport *portp, int state);
+static void stl_sc26198flush(struct stlport *portp);
+static int stl_sc26198datastate(struct stlport *portp);
+static void stl_sc26198wait(struct stlport *portp);
+static void stl_sc26198txunflow(struct stlport *portp, struct tty_struct *tty);
+static void stl_sc26198intr(struct stlpanel *panelp, unsigned int iobase);
+static void stl_sc26198txisr(struct stlport *port);
+static void stl_sc26198rxisr(struct stlport *port, unsigned int iack);
+static void stl_sc26198rxbadch(struct stlport *portp, unsigned char status, char ch);
+static void stl_sc26198rxbadchars(struct stlport *portp);
+static void stl_sc26198otherisr(struct stlport *port, unsigned int iack);
/*****************************************************************************/
* Generic UART support structure.
*/
typedef struct uart {
- int (*panelinit)(stlbrd_t *brdp, stlpanel_t *panelp);
- void (*portinit)(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp);
- void (*setport)(stlport_t *portp, struct termios *tiosp);
- int (*getsignals)(stlport_t *portp);
- void (*setsignals)(stlport_t *portp, int dtr, int rts);
- void (*enablerxtx)(stlport_t *portp, int rx, int tx);
- void (*startrxtx)(stlport_t *portp, int rx, int tx);
- void (*disableintrs)(stlport_t *portp);
- void (*sendbreak)(stlport_t *portp, int len);
- void (*flowctrl)(stlport_t *portp, int state);
- void (*sendflow)(stlport_t *portp, int state);
- void (*flush)(stlport_t *portp);
- int (*datastate)(stlport_t *portp);
- void (*intr)(stlpanel_t *panelp, unsigned int iobase);
+ int (*panelinit)(struct stlbrd *brdp, struct stlpanel *panelp);
+ void (*portinit)(struct stlbrd *brdp, struct stlpanel *panelp, struct stlport *portp);
+ void (*setport)(struct stlport *portp, struct ktermios *tiosp);
+ int (*getsignals)(struct stlport *portp);
+ void (*setsignals)(struct stlport *portp, int dtr, int rts);
+ void (*enablerxtx)(struct stlport *portp, int rx, int tx);
+ void (*startrxtx)(struct stlport *portp, int rx, int tx);
+ void (*disableintrs)(struct stlport *portp);
+ void (*sendbreak)(struct stlport *portp, int len);
+ void (*flowctrl)(struct stlport *portp, int state);
+ void (*sendflow)(struct stlport *portp, int state);
+ void (*flush)(struct stlport *portp);
+ int (*datastate)(struct stlport *portp);
+ void (*intr)(struct stlpanel *panelp, unsigned int iobase);
} uart_t;
/*
.ioctl = stl_memioctl,
};
-/*****************************************************************************/
-
static struct class *stallion_class;
-/*
- * Loadable module initialization stuff.
- */
-
-static int __init stallion_module_init(void)
-{
- stl_init();
- return 0;
-}
-
-/*****************************************************************************/
-
-static void __exit stallion_module_exit(void)
-{
- stlbrd_t *brdp;
- stlpanel_t *panelp;
- stlport_t *portp;
- int i, j, k;
-
- pr_debug("cleanup_module()\n");
-
- printk(KERN_INFO "Unloading %s: version %s\n", stl_drvtitle,
- stl_drvversion);
-
-/*
- * Free up all allocated resources used by the ports. This includes
- * memory and interrupts. As part of this process we will also do
- * a hangup on every open port - to try to flush out any processes
- * hanging onto ports.
- */
- i = tty_unregister_driver(stl_serial);
- put_tty_driver(stl_serial);
- if (i) {
- printk("STALLION: failed to un-register tty driver, "
- "errno=%d\n", -i);
- return;
- }
- for (i = 0; i < 4; i++)
- class_device_destroy(stallion_class, MKDEV(STL_SIOMEMMAJOR, i));
- if ((i = unregister_chrdev(STL_SIOMEMMAJOR, "staliomem")))
- printk("STALLION: failed to un-register serial memory device, "
- "errno=%d\n", -i);
- class_destroy(stallion_class);
-
- for (i = 0; (i < stl_nrbrds); i++) {
- if ((brdp = stl_brds[i]) == NULL)
- continue;
-
- free_irq(brdp->irq, brdp);
-
- for (j = 0; (j < STL_MAXPANELS); j++) {
- panelp = brdp->panels[j];
- if (panelp == NULL)
- continue;
- for (k = 0; (k < STL_PORTSPERPANEL); k++) {
- portp = panelp->ports[k];
- if (portp == NULL)
- continue;
- if (portp->tty != NULL)
- stl_hangup(portp->tty);
- kfree(portp->tx.buf);
- kfree(portp);
- }
- kfree(panelp);
- }
-
- release_region(brdp->ioaddr1, brdp->iosize1);
- if (brdp->iosize2 > 0)
- release_region(brdp->ioaddr2, brdp->iosize2);
-
- kfree(brdp);
- stl_brds[i] = NULL;
- }
-}
-
-module_init(stallion_module_init);
-module_exit(stallion_module_exit);
-
-/*****************************************************************************/
-
/*
* Check for any arguments passed in on the module load command line.
*/
-static void stl_argbrds(void)
-{
- stlconf_t conf;
- stlbrd_t *brdp;
- int i;
-
- pr_debug("stl_argbrds()\n");
-
- for (i = stl_nrbrds; (i < stl_nargs); i++) {
- memset(&conf, 0, sizeof(conf));
- if (stl_parsebrd(&conf, stl_brdsp[i]) == 0)
- continue;
- if ((brdp = stl_allocbrd()) == NULL)
- continue;
- stl_nrbrds = i + 1;
- brdp->brdnr = i;
- brdp->brdtype = conf.brdtype;
- brdp->ioaddr1 = conf.ioaddr1;
- brdp->ioaddr2 = conf.ioaddr2;
- brdp->irq = conf.irq;
- brdp->irqtype = conf.irqtype;
- stl_brdinit(brdp);
- }
-}
-
-/*****************************************************************************/
-
-/*
- * Convert an ascii string number into an unsigned long.
- */
-
-static unsigned long stl_atol(char *str)
-{
- unsigned long val;
- int base, c;
- char *sp;
-
- val = 0;
- sp = str;
- if ((*sp == '0') && (*(sp+1) == 'x')) {
- base = 16;
- sp += 2;
- } else if (*sp == '0') {
- base = 8;
- sp++;
- } else {
- base = 10;
- }
-
- for (; (*sp != 0); sp++) {
- c = (*sp > '9') ? (TOLOWER(*sp) - 'a' + 10) : (*sp - '0');
- if ((c < 0) || (c >= base)) {
- printk("STALLION: invalid argument %s\n", str);
- val = 0;
- break;
- }
- val = (val * base) + c;
- }
- return val;
-}
-
/*****************************************************************************/
/*
* Parse the supplied argument string, into the board conf struct.
*/
-static int stl_parsebrd(stlconf_t *confp, char **argp)
+static int __init stl_parsebrd(struct stlconf *confp, char **argp)
{
char *sp;
- int i;
+ unsigned int i;
pr_debug("stl_parsebrd(confp=%p,argp=%p)\n", confp, argp);
if ((argp[0] == NULL) || (*argp[0] == 0))
return 0;
- for (sp = argp[0], i = 0; ((*sp != 0) && (i < 25)); sp++, i++)
- *sp = TOLOWER(*sp);
+ for (sp = argp[0], i = 0; (*sp != 0) && (i < 25); sp++, i++)
+ *sp = tolower(*sp);
- for (i = 0; i < ARRAY_SIZE(stl_brdstr); i++) {
+ for (i = 0; i < ARRAY_SIZE(stl_brdstr); i++)
if (strcmp(stl_brdstr[i].name, argp[0]) == 0)
break;
- }
+
if (i == ARRAY_SIZE(stl_brdstr)) {
printk("STALLION: unknown board name, %s?\n", argp[0]);
return 0;
i = 1;
if ((argp[i] != NULL) && (*argp[i] != 0))
- confp->ioaddr1 = stl_atol(argp[i]);
+ confp->ioaddr1 = simple_strtoul(argp[i], NULL, 0);
i++;
if (confp->brdtype == BRD_ECH) {
if ((argp[i] != NULL) && (*argp[i] != 0))
- confp->ioaddr2 = stl_atol(argp[i]);
+ confp->ioaddr2 = simple_strtoul(argp[i], NULL, 0);
i++;
}
if ((argp[i] != NULL) && (*argp[i] != 0))
- confp->irq = stl_atol(argp[i]);
+ confp->irq = simple_strtoul(argp[i], NULL, 0);
return 1;
}
* Allocate a new board structure. Fill out the basic info in it.
*/
-static stlbrd_t *stl_allocbrd(void)
+static struct stlbrd *stl_allocbrd(void)
{
- stlbrd_t *brdp;
+ struct stlbrd *brdp;
- brdp = kzalloc(sizeof(stlbrd_t), GFP_KERNEL);
+ brdp = kzalloc(sizeof(struct stlbrd), GFP_KERNEL);
if (!brdp) {
printk("STALLION: failed to allocate memory (size=%Zd)\n",
- sizeof(stlbrd_t));
+ sizeof(struct stlbrd));
return NULL;
}
static int stl_open(struct tty_struct *tty, struct file *filp)
{
- stlport_t *portp;
- stlbrd_t *brdp;
- unsigned int minordev;
- int brdnr, panelnr, portnr, rc;
+ struct stlport *portp;
+ struct stlbrd *brdp;
+ unsigned int minordev, brdnr, panelnr;
+ int portnr, rc;
pr_debug("stl_open(tty=%p,filp=%p): device=%s\n", tty, filp, tty->name);
if (brdp == NULL)
return -ENODEV;
minordev = MINOR2PORT(minordev);
- for (portnr = -1, panelnr = 0; (panelnr < STL_MAXPANELS); panelnr++) {
+ for (portnr = -1, panelnr = 0; panelnr < STL_MAXPANELS; panelnr++) {
if (brdp->panels[panelnr] == NULL)
break;
if (minordev < brdp->panels[panelnr]->nrports) {
* previous opens still in effect. If we are a normal serial device
* then also we might have to wait for carrier.
*/
- if (!(filp->f_flags & O_NONBLOCK)) {
+ if (!(filp->f_flags & O_NONBLOCK))
if ((rc = stl_waitcarrier(portp, filp)) != 0)
return rc;
- }
+
portp->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
* maybe because if we are clocal then we don't need to wait...
*/
-static int stl_waitcarrier(stlport_t *portp, struct file *filp)
+static int stl_waitcarrier(struct stlport *portp, struct file *filp)
{
unsigned long flags;
int rc, doclocal;
break;
}
if (((portp->flags & ASYNC_CLOSING) == 0) &&
- (doclocal || (portp->sigs & TIOCM_CD))) {
+ (doclocal || (portp->sigs & TIOCM_CD)))
break;
- }
if (signal_pending(current)) {
rc = -ERESTARTSYS;
break;
/*****************************************************************************/
+static void stl_flushbuffer(struct tty_struct *tty)
+{
+ struct stlport *portp;
+
+ pr_debug("stl_flushbuffer(tty=%p)\n", tty);
+
+ if (tty == NULL)
+ return;
+ portp = tty->driver_data;
+ if (portp == NULL)
+ return;
+
+ stl_flush(portp);
+ tty_wakeup(tty);
+}
+
+/*****************************************************************************/
+
+static void stl_waituntilsent(struct tty_struct *tty, int timeout)
+{
+ struct stlport *portp;
+ unsigned long tend;
+
+ pr_debug("stl_waituntilsent(tty=%p,timeout=%d)\n", tty, timeout);
+
+ if (tty == NULL)
+ return;
+ portp = tty->driver_data;
+ if (portp == NULL)
+ return;
+
+ if (timeout == 0)
+ timeout = HZ;
+ tend = jiffies + timeout;
+
+ while (stl_datastate(portp)) {
+ if (signal_pending(current))
+ break;
+ msleep_interruptible(20);
+ if (time_after_eq(jiffies, tend))
+ break;
+ }
+}
+
+/*****************************************************************************/
+
static void stl_close(struct tty_struct *tty, struct file *filp)
{
- stlport_t *portp;
+ struct stlport *portp;
unsigned long flags;
pr_debug("stl_close(tty=%p,filp=%p)\n", tty, filp);
static int stl_write(struct tty_struct *tty, const unsigned char *buf, int count)
{
- stlport_t *portp;
+ struct stlport *portp;
unsigned int len, stlen;
unsigned char *chbuf;
char *head, *tail;
stlen = len;
}
- len = MIN(len, count);
+ len = min(len, (unsigned int)count);
count = 0;
while (len > 0) {
- stlen = MIN(len, stlen);
+ stlen = min(len, stlen);
memcpy(head, chbuf, stlen);
len -= stlen;
chbuf += stlen;
static void stl_putchar(struct tty_struct *tty, unsigned char ch)
{
- stlport_t *portp;
+ struct stlport *portp;
unsigned int len;
char *head, *tail;
static void stl_flushchars(struct tty_struct *tty)
{
- stlport_t *portp;
+ struct stlport *portp;
pr_debug("stl_flushchars(tty=%p)\n", tty);
static int stl_writeroom(struct tty_struct *tty)
{
- stlport_t *portp;
+ struct stlport *portp;
char *head, *tail;
pr_debug("stl_writeroom(tty=%p)\n", tty);
head = portp->tx.head;
tail = portp->tx.tail;
- return ((head >= tail) ? (STL_TXBUFSIZE - (head - tail) - 1) : (tail - head - 1));
+ return (head >= tail) ? (STL_TXBUFSIZE - (head - tail) - 1) : (tail - head - 1);
}
/*****************************************************************************/
static int stl_charsinbuffer(struct tty_struct *tty)
{
- stlport_t *portp;
+ struct stlport *portp;
unsigned int size;
char *head, *tail;
* Generate the serial struct info.
*/
-static int stl_getserial(stlport_t *portp, struct serial_struct __user *sp)
+static int stl_getserial(struct stlport *portp, struct serial_struct __user *sp)
{
struct serial_struct sio;
- stlbrd_t *brdp;
+ struct stlbrd *brdp;
pr_debug("stl_getserial(portp=%p,sp=%p)\n", portp, sp);
* just quietly ignore any requests to change irq, etc.
*/
-static int stl_setserial(stlport_t *portp, struct serial_struct __user *sp)
+static int stl_setserial(struct stlport *portp, struct serial_struct __user *sp)
{
struct serial_struct sio;
static int stl_tiocmget(struct tty_struct *tty, struct file *file)
{
- stlport_t *portp;
+ struct stlport *portp;
if (tty == NULL)
return -ENODEV;
static int stl_tiocmset(struct tty_struct *tty, struct file *file,
unsigned int set, unsigned int clear)
{
- stlport_t *portp;
+ struct stlport *portp;
int rts = -1, dtr = -1;
if (tty == NULL)
static int stl_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg)
{
- stlport_t *portp;
+ struct stlport *portp;
unsigned int ival;
int rc;
void __user *argp = (void __user *)arg;
return -ENODEV;
if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
- (cmd != COM_GETPORTSTATS) && (cmd != COM_CLRPORTSTATS)) {
+ (cmd != COM_GETPORTSTATS) && (cmd != COM_CLRPORTSTATS))
if (tty->flags & (1 << TTY_IO_ERROR))
return -EIO;
- }
rc = 0;
/*****************************************************************************/
-static void stl_settermios(struct tty_struct *tty, struct termios *old)
+/*
+ * Start the transmitter again. Just turn TX interrupts back on.
+ */
+
+static void stl_start(struct tty_struct *tty)
+{
+ struct stlport *portp;
+
+ pr_debug("stl_start(tty=%p)\n", tty);
+
+ if (tty == NULL)
+ return;
+ portp = tty->driver_data;
+ if (portp == NULL)
+ return;
+ stl_startrxtx(portp, -1, 1);
+}
+
+/*****************************************************************************/
+
+static void stl_settermios(struct tty_struct *tty, struct ktermios *old)
{
- stlport_t *portp;
- struct termios *tiosp;
+ struct stlport *portp;
+ struct ktermios *tiosp;
pr_debug("stl_settermios(tty=%p,old=%p)\n", tty, old);
static void stl_throttle(struct tty_struct *tty)
{
- stlport_t *portp;
+ struct stlport *portp;
pr_debug("stl_throttle(tty=%p)\n", tty);
static void stl_unthrottle(struct tty_struct *tty)
{
- stlport_t *portp;
+ struct stlport *portp;
pr_debug("stl_unthrottle(tty=%p)\n", tty);
static void stl_stop(struct tty_struct *tty)
{
- stlport_t *portp;
+ struct stlport *portp;
pr_debug("stl_stop(tty=%p)\n", tty);
/*****************************************************************************/
-/*
- * Start the transmitter again. Just turn TX interrupts back on.
- */
-
-static void stl_start(struct tty_struct *tty)
-{
- stlport_t *portp;
-
- pr_debug("stl_start(tty=%p)\n", tty);
-
- if (tty == NULL)
- return;
- portp = tty->driver_data;
- if (portp == NULL)
- return;
- stl_startrxtx(portp, -1, 1);
-}
-
-/*****************************************************************************/
-
/*
* Hangup this port. This is pretty much like closing the port, only
* a little more brutal. No waiting for data to drain. Shutdown the
static void stl_hangup(struct tty_struct *tty)
{
- stlport_t *portp;
+ struct stlport *portp;
pr_debug("stl_hangup(tty=%p)\n", tty);
/*****************************************************************************/
-static void stl_flushbuffer(struct tty_struct *tty)
-{
- stlport_t *portp;
-
- pr_debug("stl_flushbuffer(tty=%p)\n", tty);
-
- if (tty == NULL)
- return;
- portp = tty->driver_data;
- if (portp == NULL)
- return;
-
- stl_flush(portp);
- tty_wakeup(tty);
-}
-
-/*****************************************************************************/
-
static void stl_breakctl(struct tty_struct *tty, int state)
{
- stlport_t *portp;
+ struct stlport *portp;
pr_debug("stl_breakctl(tty=%p,state=%d)\n", tty, state);
/*****************************************************************************/
-static void stl_waituntilsent(struct tty_struct *tty, int timeout)
-{
- stlport_t *portp;
- unsigned long tend;
-
- pr_debug("stl_waituntilsent(tty=%p,timeout=%d)\n", tty, timeout);
-
- if (tty == NULL)
- return;
- portp = tty->driver_data;
- if (portp == NULL)
- return;
-
- if (timeout == 0)
- timeout = HZ;
- tend = jiffies + timeout;
-
- while (stl_datastate(portp)) {
- if (signal_pending(current))
- break;
- msleep_interruptible(20);
- if (time_after_eq(jiffies, tend))
- break;
- }
-}
-
-/*****************************************************************************/
-
static void stl_sendxchar(struct tty_struct *tty, char ch)
{
- stlport_t *portp;
+ struct stlport *portp;
pr_debug("stl_sendxchar(tty=%p,ch=%x)\n", tty, ch);
* short then padded with spaces).
*/
-static int stl_portinfo(stlport_t *portp, int portnr, char *pos)
+static int stl_portinfo(struct stlport *portp, int portnr, char *pos)
{
char *sp;
int sigs, cnt;
*sp = ' ';
sp += cnt;
- for (cnt = (sp - pos); (cnt < (MAXLINE - 1)); cnt++)
+ for (cnt = sp - pos; cnt < (MAXLINE - 1); cnt++)
*sp++ = ' ';
if (cnt >= MAXLINE)
pos[(MAXLINE - 2)] = '+';
static int stl_readproc(char *page, char **start, off_t off, int count, int *eof, void *data)
{
- stlbrd_t *brdp;
- stlpanel_t *panelp;
- stlport_t *portp;
- int brdnr, panelnr, portnr, totalport;
- int curoff, maxoff;
+ struct stlbrd *brdp;
+ struct stlpanel *panelp;
+ struct stlport *portp;
+ unsigned int brdnr, panelnr, portnr;
+ int totalport, curoff, maxoff;
char *pos;
pr_debug("stl_readproc(page=%p,start=%p,off=%lx,count=%d,eof=%p,"
* We scan through for each board, panel and port. The offset is
* calculated on the fly, and irrelevant ports are skipped.
*/
- for (brdnr = 0; (brdnr < stl_nrbrds); brdnr++) {
+ for (brdnr = 0; brdnr < stl_nrbrds; brdnr++) {
brdp = stl_brds[brdnr];
if (brdp == NULL)
continue;
}
totalport = brdnr * STL_MAXPORTS;
- for (panelnr = 0; (panelnr < brdp->nrpanels); panelnr++) {
+ for (panelnr = 0; panelnr < brdp->nrpanels; panelnr++) {
panelp = brdp->panels[panelnr];
if (panelp == NULL)
continue;
continue;
}
- for (portnr = 0; (portnr < panelp->nrports); portnr++,
+ for (portnr = 0; portnr < panelp->nrports; portnr++,
totalport++) {
portp = panelp->ports[portnr];
if (portp == NULL)
stl_readdone:
*start = page;
- return (pos - page);
+ return pos - page;
}
/*****************************************************************************/
static irqreturn_t stl_intr(int irq, void *dev_id)
{
- stlbrd_t *brdp = dev_id;
+ struct stlbrd *brdp = dev_id;
pr_debug("stl_intr(brdp=%p,irq=%d)\n", brdp, irq);
* Interrupt service routine for EasyIO board types.
*/
-static int stl_eiointr(stlbrd_t *brdp)
+static int stl_eiointr(struct stlbrd *brdp)
{
- stlpanel_t *panelp;
+ struct stlpanel *panelp;
unsigned int iobase;
int handled = 0;
* Interrupt service routine for ECH-AT board types.
*/
-static int stl_echatintr(stlbrd_t *brdp)
+static int stl_echatintr(struct stlbrd *brdp)
{
- stlpanel_t *panelp;
- unsigned int ioaddr;
- int bnknr;
+ struct stlpanel *panelp;
+ unsigned int ioaddr, bnknr;
int handled = 0;
outb((brdp->ioctrlval | ECH_BRDENABLE), brdp->ioctrl);
while (inb(brdp->iostatus) & ECH_INTRPEND) {
handled = 1;
- for (bnknr = 0; (bnknr < brdp->nrbnks); bnknr++) {
+ for (bnknr = 0; bnknr < brdp->nrbnks; bnknr++) {
ioaddr = brdp->bnkstataddr[bnknr];
if (inb(ioaddr) & ECH_PNLINTRPEND) {
panelp = brdp->bnk2panel[bnknr];
* Interrupt service routine for ECH-MCA board types.
*/
-static int stl_echmcaintr(stlbrd_t *brdp)
+static int stl_echmcaintr(struct stlbrd *brdp)
{
- stlpanel_t *panelp;
- unsigned int ioaddr;
- int bnknr;
+ struct stlpanel *panelp;
+ unsigned int ioaddr, bnknr;
int handled = 0;
while (inb(brdp->iostatus) & ECH_INTRPEND) {
handled = 1;
- for (bnknr = 0; (bnknr < brdp->nrbnks); bnknr++) {
+ for (bnknr = 0; bnknr < brdp->nrbnks; bnknr++) {
ioaddr = brdp->bnkstataddr[bnknr];
if (inb(ioaddr) & ECH_PNLINTRPEND) {
panelp = brdp->bnk2panel[bnknr];
* Interrupt service routine for ECH-PCI board types.
*/
-static int stl_echpciintr(stlbrd_t *brdp)
+static int stl_echpciintr(struct stlbrd *brdp)
{
- stlpanel_t *panelp;
- unsigned int ioaddr;
- int bnknr, recheck;
+ struct stlpanel *panelp;
+ unsigned int ioaddr, bnknr, recheck;
int handled = 0;
while (1) {
recheck = 0;
- for (bnknr = 0; (bnknr < brdp->nrbnks); bnknr++) {
+ for (bnknr = 0; bnknr < brdp->nrbnks; bnknr++) {
outb(brdp->bnkpageaddr[bnknr], brdp->ioctrl);
ioaddr = brdp->bnkstataddr[bnknr];
if (inb(ioaddr) & ECH_PNLINTRPEND) {
* Interrupt service routine for ECH-8/64-PCI board types.
*/
-static int stl_echpci64intr(stlbrd_t *brdp)
+static int stl_echpci64intr(struct stlbrd *brdp)
{
- stlpanel_t *panelp;
- unsigned int ioaddr;
- int bnknr;
+ struct stlpanel *panelp;
+ unsigned int ioaddr, bnknr;
int handled = 0;
while (inb(brdp->ioctrl) & 0x1) {
handled = 1;
- for (bnknr = 0; (bnknr < brdp->nrbnks); bnknr++) {
+ for (bnknr = 0; bnknr < brdp->nrbnks; bnknr++) {
ioaddr = brdp->bnkstataddr[bnknr];
if (inb(ioaddr) & ECH_PNLINTRPEND) {
panelp = brdp->bnk2panel[bnknr];
*/
static void stl_offintr(struct work_struct *work)
{
- stlport_t *portp = container_of(work, stlport_t, tqueue);
+ struct stlport *portp = container_of(work, struct stlport, tqueue);
struct tty_struct *tty;
unsigned int oldsigs;
if (tty == NULL)
return;
- lock_kernel();
- if (test_bit(ASYI_TXLOW, &portp->istate)) {
+ if (test_bit(ASYI_TXLOW, &portp->istate))
tty_wakeup(tty);
- }
+
if (test_bit(ASYI_DCDCHANGE, &portp->istate)) {
clear_bit(ASYI_DCDCHANGE, &portp->istate);
oldsigs = portp->sigs;
portp->sigs = stl_getsignals(portp);
if ((portp->sigs & TIOCM_CD) && ((oldsigs & TIOCM_CD) == 0))
wake_up_interruptible(&portp->open_wait);
- if ((oldsigs & TIOCM_CD) && ((portp->sigs & TIOCM_CD) == 0)) {
+ if ((oldsigs & TIOCM_CD) && ((portp->sigs & TIOCM_CD) == 0))
if (portp->flags & ASYNC_CHECK_CD)
tty_hangup(tty); /* FIXME: module removal race here - AKPM */
- }
}
- unlock_kernel();
}
/*****************************************************************************/
* Initialize all the ports on a panel.
*/
-static int __init stl_initports(stlbrd_t *brdp, stlpanel_t *panelp)
+static int __devinit stl_initports(struct stlbrd *brdp, struct stlpanel *panelp)
{
- stlport_t *portp;
- int chipmask, i;
+ struct stlport *portp;
+ unsigned int i;
+ int chipmask;
pr_debug("stl_initports(brdp=%p,panelp=%p)\n", brdp, panelp);
* All UART's are initialized (if found!). Now go through and setup
* each ports data structures.
*/
- for (i = 0; (i < panelp->nrports); i++) {
- portp = kzalloc(sizeof(stlport_t), GFP_KERNEL);
+ for (i = 0; i < panelp->nrports; i++) {
+ portp = kzalloc(sizeof(struct stlport), GFP_KERNEL);
if (!portp) {
printk("STALLION: failed to allocate memory "
- "(size=%Zd)\n", sizeof(stlport_t));
+ "(size=%Zd)\n", sizeof(struct stlport));
break;
}
stl_portinit(brdp, panelp, portp);
}
- return(0);
+ return 0;
+}
+
+static void stl_cleanup_panels(struct stlbrd *brdp)
+{
+ struct stlpanel *panelp;
+ struct stlport *portp;
+ unsigned int j, k;
+
+ for (j = 0; j < STL_MAXPANELS; j++) {
+ panelp = brdp->panels[j];
+ if (panelp == NULL)
+ continue;
+ for (k = 0; k < STL_PORTSPERPANEL; k++) {
+ portp = panelp->ports[k];
+ if (portp == NULL)
+ continue;
+ if (portp->tty != NULL)
+ stl_hangup(portp->tty);
+ kfree(portp->tx.buf);
+ kfree(portp);
+ }
+ kfree(panelp);
+ }
}
/*****************************************************************************/
* Try to find and initialize an EasyIO board.
*/
-static inline int stl_initeio(stlbrd_t *brdp)
+static int __devinit stl_initeio(struct stlbrd *brdp)
{
- stlpanel_t *panelp;
+ struct stlpanel *panelp;
unsigned int status;
char *name;
- int rc;
+ int retval;
pr_debug("stl_initeio(brdp=%p)\n", brdp);
(stl_vecmap[brdp->irq] == (unsigned char) 0xff)) {
printk("STALLION: invalid irq=%d for brd=%d\n",
brdp->irq, brdp->brdnr);
- return(-EINVAL);
+ retval = -EINVAL;
+ goto err;
}
outb((stl_vecmap[brdp->irq] | EIO_0WS |
((brdp->irqtype) ? EIO_INTLEVEL : EIO_INTEDGE)),
brdp->ioctrl);
}
+ retval = -EBUSY;
if (!request_region(brdp->ioaddr1, brdp->iosize1, name)) {
printk(KERN_WARNING "STALLION: Warning, board %d I/O address "
"%x conflicts with another device\n", brdp->brdnr,
brdp->ioaddr1);
- return(-EBUSY);
+ goto err;
}
if (brdp->iosize2 > 0)
printk(KERN_WARNING "STALLION: Warning, also "
"releasing board %d I/O address %x \n",
brdp->brdnr, brdp->ioaddr1);
- release_region(brdp->ioaddr1, brdp->iosize1);
- return(-EBUSY);
+ goto err_rel1;
}
/*
brdp->clk = CD1400_CLK;
brdp->isr = stl_eiointr;
+ retval = -ENODEV;
switch (status & EIO_IDBITMASK) {
case EIO_8PORTM:
brdp->clk = CD1400_CLK8M;
brdp->nrports = 16;
break;
default:
- return(-ENODEV);
+ goto err_rel2;
}
break;
default:
- return(-ENODEV);
+ goto err_rel2;
}
/*
* can complete the setup.
*/
- panelp = kzalloc(sizeof(stlpanel_t), GFP_KERNEL);
+ panelp = kzalloc(sizeof(struct stlpanel), GFP_KERNEL);
if (!panelp) {
printk(KERN_WARNING "STALLION: failed to allocate memory "
- "(size=%Zd)\n", sizeof(stlpanel_t));
- return -ENOMEM;
+ "(size=%Zd)\n", sizeof(struct stlpanel));
+ retval = -ENOMEM;
+ goto err_rel2;
}
panelp->magic = STL_PANELMAGIC;
if (request_irq(brdp->irq, stl_intr, IRQF_SHARED, name, brdp) != 0) {
printk("STALLION: failed to register interrupt "
"routine for %s irq=%d\n", name, brdp->irq);
- rc = -ENODEV;
- } else {
- rc = 0;
+ retval = -ENODEV;
+ goto err_fr;
}
- return rc;
+
+ return 0;
+err_fr:
+ stl_cleanup_panels(brdp);
+err_rel2:
+ if (brdp->iosize2 > 0)
+ release_region(brdp->ioaddr2, brdp->iosize2);
+err_rel1:
+ release_region(brdp->ioaddr1, brdp->iosize1);
+err:
+ return retval;
}
/*****************************************************************************/
* dealing with all types of ECH board.
*/
-static inline int stl_initech(stlbrd_t *brdp)
+static int __devinit stl_initech(struct stlbrd *brdp)
{
- stlpanel_t *panelp;
- unsigned int status, nxtid, ioaddr, conflict;
- int panelnr, banknr, i;
+ struct stlpanel *panelp;
+ unsigned int status, nxtid, ioaddr, conflict, panelnr, banknr, i;
+ int retval;
char *name;
pr_debug("stl_initech(brdp=%p)\n", brdp);
brdp->ioctrl = brdp->ioaddr1 + 1;
brdp->iostatus = brdp->ioaddr1 + 1;
status = inb(brdp->iostatus);
- if ((status & ECH_IDBITMASK) != ECH_ID)
- return(-ENODEV);
+ if ((status & ECH_IDBITMASK) != ECH_ID) {
+ retval = -ENODEV;
+ goto err;
+ }
if ((brdp->irq < 0) || (brdp->irq > 15) ||
(stl_vecmap[brdp->irq] == (unsigned char) 0xff)) {
printk("STALLION: invalid irq=%d for brd=%d\n",
brdp->irq, brdp->brdnr);
- return(-EINVAL);
+ retval = -EINVAL;
+ goto err;
}
status = ((brdp->ioaddr2 & ECH_ADDR2MASK) >> 1);
status |= (stl_vecmap[brdp->irq] << 1);
outb((status | ECH_BRDRESET), brdp->ioaddr1);
brdp->ioctrlval = ECH_INTENABLE |
((brdp->irqtype) ? ECH_INTLEVEL : ECH_INTEDGE);
- for (i = 0; (i < 10); i++)
+ for (i = 0; i < 10; i++)
outb((brdp->ioctrlval | ECH_BRDENABLE), brdp->ioctrl);
brdp->iosize1 = 2;
brdp->iosize2 = 32;
brdp->ioctrl = brdp->ioaddr1 + 0x20;
brdp->iostatus = brdp->ioctrl;
status = inb(brdp->iostatus);
- if ((status & ECH_IDBITMASK) != ECH_ID)
- return(-ENODEV);
+ if ((status & ECH_IDBITMASK) != ECH_ID) {
+ retval = -ENODEV;
+ goto err;
+ }
if ((brdp->irq < 0) || (brdp->irq > 15) ||
(stl_vecmap[brdp->irq] == (unsigned char) 0xff)) {
printk("STALLION: invalid irq=%d for brd=%d\n",
brdp->irq, brdp->brdnr);
- return(-EINVAL);
+ retval = -EINVAL;
+ goto err;
}
outb(ECHMC_BRDRESET, brdp->ioctrl);
outb(ECHMC_INTENABLE, brdp->ioctrl);
default:
printk("STALLION: unknown board type=%d\n", brdp->brdtype);
- return(-EINVAL);
- break;
+ retval = -EINVAL;
+ goto err;
}
/*
* Check boards for possible IO address conflicts and return fail status
* if an IO conflict found.
*/
+ retval = -EBUSY;
if (!request_region(brdp->ioaddr1, brdp->iosize1, name)) {
printk(KERN_WARNING "STALLION: Warning, board %d I/O address "
"%x conflicts with another device\n", brdp->brdnr,
brdp->ioaddr1);
- return(-EBUSY);
+ goto err;
}
if (brdp->iosize2 > 0)
printk(KERN_WARNING "STALLION: Warning, also "
"releasing board %d I/O address %x \n",
brdp->brdnr, brdp->ioaddr1);
- release_region(brdp->ioaddr1, brdp->iosize1);
- return(-EBUSY);
+ goto err_rel1;
}
/*
panelnr = 0;
nxtid = 0;
- for (i = 0; (i < STL_MAXPANELS); i++) {
+ for (i = 0; i < STL_MAXPANELS; i++) {
if (brdp->brdtype == BRD_ECHPCI) {
outb(nxtid, brdp->ioctrl);
ioaddr = brdp->ioaddr2;
status = inb(ioaddr + ECH_PNLSTATUS);
if ((status & ECH_PNLIDMASK) != nxtid)
break;
- panelp = kzalloc(sizeof(stlpanel_t), GFP_KERNEL);
+ panelp = kzalloc(sizeof(struct stlpanel), GFP_KERNEL);
if (!panelp) {
printk("STALLION: failed to allocate memory "
- "(size=%Zd)\n", sizeof(stlpanel_t));
- break;
+ "(size=%Zd)\n", sizeof(struct stlpanel));
+ retval = -ENOMEM;
+ goto err_fr;
}
panelp->magic = STL_PANELMAGIC;
panelp->brdnr = brdp->brdnr;
brdp->bnkpageaddr[banknr] = nxtid;
brdp->bnkstataddr[banknr++] = ioaddr + 4 +
ECH_PNLSTATUS;
- } else {
+ } else
panelp->nrports = 8;
- }
} else {
panelp->uartp = &stl_cd1400uart;
panelp->isr = stl_cd1400echintr;
brdp->nrports += panelp->nrports;
brdp->panels[panelnr++] = panelp;
if ((brdp->brdtype != BRD_ECHPCI) &&
- (ioaddr >= (brdp->ioaddr2 + brdp->iosize2)))
- break;
+ (ioaddr >= (brdp->ioaddr2 + brdp->iosize2))) {
+ retval = -EINVAL;
+ goto err_fr;
+ }
}
brdp->nrpanels = panelnr;
if (request_irq(brdp->irq, stl_intr, IRQF_SHARED, name, brdp) != 0) {
printk("STALLION: failed to register interrupt "
"routine for %s irq=%d\n", name, brdp->irq);
- i = -ENODEV;
- } else {
- i = 0;
+ retval = -ENODEV;
+ goto err_fr;
}
- return(i);
+ return 0;
+err_fr:
+ stl_cleanup_panels(brdp);
+ if (brdp->iosize2 > 0)
+ release_region(brdp->ioaddr2, brdp->iosize2);
+err_rel1:
+ release_region(brdp->ioaddr1, brdp->iosize1);
+err:
+ return retval;
}
/*****************************************************************************/
* since the initial search and setup is very different.
*/
-static int __init stl_brdinit(stlbrd_t *brdp)
+static int __devinit stl_brdinit(struct stlbrd *brdp)
{
- int i;
+ int i, retval;
pr_debug("stl_brdinit(brdp=%p)\n", brdp);
switch (brdp->brdtype) {
case BRD_EASYIO:
case BRD_EASYIOPCI:
- stl_initeio(brdp);
+ retval = stl_initeio(brdp);
+ if (retval)
+ goto err;
break;
case BRD_ECH:
case BRD_ECHMC:
case BRD_ECHPCI:
case BRD_ECH64PCI:
- stl_initech(brdp);
+ retval = stl_initech(brdp);
+ if (retval)
+ goto err;
break;
default:
printk("STALLION: board=%d is unknown board type=%d\n",
brdp->brdnr, brdp->brdtype);
- return(ENODEV);
+ retval = -ENODEV;
+ goto err;
}
- stl_brds[brdp->brdnr] = brdp;
if ((brdp->state & BRD_FOUND) == 0) {
printk("STALLION: %s board not found, board=%d io=%x irq=%d\n",
stl_brdnames[brdp->brdtype], brdp->brdnr,
brdp->ioaddr1, brdp->irq);
- return(ENODEV);
+ goto err_free;
}
- for (i = 0; (i < STL_MAXPANELS); i++)
+ for (i = 0; i < STL_MAXPANELS; i++)
if (brdp->panels[i] != NULL)
stl_initports(brdp, brdp->panels[i]);
"nrpanels=%d nrports=%d\n", stl_brdnames[brdp->brdtype],
brdp->brdnr, brdp->ioaddr1, brdp->irq, brdp->nrpanels,
brdp->nrports);
- return(0);
+
+ return 0;
+err_free:
+ free_irq(brdp->irq, brdp);
+
+ stl_cleanup_panels(brdp);
+
+ release_region(brdp->ioaddr1, brdp->iosize1);
+ if (brdp->iosize2 > 0)
+ release_region(brdp->ioaddr2, brdp->iosize2);
+err:
+ return retval;
}
/*****************************************************************************/
* Find the next available board number that is free.
*/
-static inline int stl_getbrdnr(void)
+static int __devinit stl_getbrdnr(void)
{
- int i;
+ unsigned int i;
- for (i = 0; (i < STL_MAXBRDS); i++) {
+ for (i = 0; i < STL_MAXBRDS; i++)
if (stl_brds[i] == NULL) {
if (i >= stl_nrbrds)
stl_nrbrds = i + 1;
- return(i);
+ return i;
}
- }
- return(-1);
+
+ return -1;
}
/*****************************************************************************/
-
-#ifdef CONFIG_PCI
-
/*
* We have a Stallion board. Allocate a board structure and
* initialize it. Read its IO and IRQ resources from PCI
* configuration space.
*/
-static inline int stl_initpcibrd(int brdtype, struct pci_dev *devp)
+static int __devinit stl_pciprobe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
{
- stlbrd_t *brdp;
-
- pr_debug("stl_initpcibrd(brdtype=%d,busnr=%x,devnr=%x)\n", brdtype,
- devp->bus->number, devp->devfn);
-
- if (pci_enable_device(devp))
- return(-EIO);
- if ((brdp = stl_allocbrd()) == NULL)
- return(-ENOMEM);
- if ((brdp->brdnr = stl_getbrdnr()) < 0) {
- printk("STALLION: too many boards found, "
+ struct stlbrd *brdp;
+ unsigned int i, brdtype = ent->driver_data;
+ int brdnr, retval = -ENODEV;
+
+ if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE)
+ goto err;
+
+ retval = pci_enable_device(pdev);
+ if (retval)
+ goto err;
+ brdp = stl_allocbrd();
+ if (brdp == NULL) {
+ retval = -ENOMEM;
+ goto err;
+ }
+ mutex_lock(&stl_brdslock);
+ brdnr = stl_getbrdnr();
+ if (brdnr < 0) {
+ dev_err(&pdev->dev, "too many boards found, "
"maximum supported %d\n", STL_MAXBRDS);
- return(0);
+ mutex_unlock(&stl_brdslock);
+ retval = -ENODEV;
+ goto err_fr;
}
- brdp->brdtype = brdtype;
+ brdp->brdnr = (unsigned int)brdnr;
+ stl_brds[brdp->brdnr] = brdp;
+ mutex_unlock(&stl_brdslock);
-/*
- * Different Stallion boards use the BAR registers in different ways,
- * so set up io addresses based on board type.
- */
- pr_debug("%s(%d): BAR[]=%Lx,%Lx,%Lx,%Lx IRQ=%x\n", __FILE__, __LINE__,
- pci_resource_start(devp, 0), pci_resource_start(devp, 1),
- pci_resource_start(devp, 2), pci_resource_start(devp, 3), devp->irq);
+ brdp->brdtype = brdtype;
+ brdp->state |= STL_PROBED;
/*
* We have all resources from the board, so let's setup the actual
*/
switch (brdtype) {
case BRD_ECHPCI:
- brdp->ioaddr2 = pci_resource_start(devp, 0);
- brdp->ioaddr1 = pci_resource_start(devp, 1);
+ brdp->ioaddr2 = pci_resource_start(pdev, 0);
+ brdp->ioaddr1 = pci_resource_start(pdev, 1);
break;
case BRD_ECH64PCI:
- brdp->ioaddr2 = pci_resource_start(devp, 2);
- brdp->ioaddr1 = pci_resource_start(devp, 1);
+ brdp->ioaddr2 = pci_resource_start(pdev, 2);
+ brdp->ioaddr1 = pci_resource_start(pdev, 1);
break;
case BRD_EASYIOPCI:
- brdp->ioaddr1 = pci_resource_start(devp, 2);
- brdp->ioaddr2 = pci_resource_start(devp, 1);
+ brdp->ioaddr1 = pci_resource_start(pdev, 2);
+ brdp->ioaddr2 = pci_resource_start(pdev, 1);
break;
default:
- printk("STALLION: unknown PCI board type=%d\n", brdtype);
+ dev_err(&pdev->dev, "unknown PCI board type=%u\n", brdtype);
break;
}
- brdp->irq = devp->irq;
- stl_brdinit(brdp);
-
- return(0);
-}
-
-/*****************************************************************************/
-
-/*
- * Find all Stallion PCI boards that might be installed. Initialize each
- * one as it is found.
- */
-
-
-static inline int stl_findpcibrds(void)
-{
- struct pci_dev *dev = NULL;
- int i, rc;
-
- pr_debug("stl_findpcibrds()\n");
-
- for (i = 0; (i < stl_nrpcibrds); i++)
- while ((dev = pci_find_device(stl_pcibrds[i].vendid,
- stl_pcibrds[i].devid, dev))) {
+ brdp->irq = pdev->irq;
+ retval = stl_brdinit(brdp);
+ if (retval)
+ goto err_null;
-/*
- * Found a device on the PCI bus that has our vendor and
- * device ID. Need to check now that it is really us.
- */
- if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
- continue;
+ pci_set_drvdata(pdev, brdp);
- rc = stl_initpcibrd(stl_pcibrds[i].brdtype, dev);
- if (rc)
- return(rc);
- }
+ for (i = 0; i < brdp->nrports; i++)
+ tty_register_device(stl_serial,
+ brdp->brdnr * STL_MAXPORTS + i, &pdev->dev);
- return(0);
+ return 0;
+err_null:
+ stl_brds[brdp->brdnr] = NULL;
+err_fr:
+ kfree(brdp);
+err:
+ return retval;
}
-#endif
-
-/*****************************************************************************/
-
-/*
- * Scan through all the boards in the configuration and see what we
- * can find. Handle EIO and the ECH boards a little differently here
- * since the initial search and setup is too different.
- */
-
-static inline int stl_initbrds(void)
+static void __devexit stl_pciremove(struct pci_dev *pdev)
{
- stlbrd_t *brdp;
- stlconf_t *confp;
- int i;
+ struct stlbrd *brdp = pci_get_drvdata(pdev);
+ unsigned int i;
- pr_debug("stl_initbrds()\n");
+ free_irq(brdp->irq, brdp);
- if (stl_nrbrds > STL_MAXBRDS) {
- printk("STALLION: too many boards in configuration table, "
- "truncating to %d\n", STL_MAXBRDS);
- stl_nrbrds = STL_MAXBRDS;
- }
+ stl_cleanup_panels(brdp);
-/*
- * Firstly scan the list of static boards configured. Allocate
- * resources and initialize the boards as found.
- */
- for (i = 0; (i < stl_nrbrds); i++) {
- confp = &stl_brdconf[i];
- stl_parsebrd(confp, stl_brdsp[i]);
- if ((brdp = stl_allocbrd()) == NULL)
- return(-ENOMEM);
- brdp->brdnr = i;
- brdp->brdtype = confp->brdtype;
- brdp->ioaddr1 = confp->ioaddr1;
- brdp->ioaddr2 = confp->ioaddr2;
- brdp->irq = confp->irq;
- brdp->irqtype = confp->irqtype;
- stl_brdinit(brdp);
- }
+ release_region(brdp->ioaddr1, brdp->iosize1);
+ if (brdp->iosize2 > 0)
+ release_region(brdp->ioaddr2, brdp->iosize2);
-/*
- * Find any dynamically supported boards. That is via module load
- * line options or auto-detected on the PCI bus.
- */
- stl_argbrds();
-#ifdef CONFIG_PCI
- stl_findpcibrds();
-#endif
+ for (i = 0; i < brdp->nrports; i++)
+ tty_unregister_device(stl_serial,
+ brdp->brdnr * STL_MAXPORTS + i);
- return(0);
+ stl_brds[brdp->brdnr] = NULL;
+ kfree(brdp);
}
+static struct pci_driver stl_pcidriver = {
+ .name = "stallion",
+ .id_table = stl_pcibrds,
+ .probe = stl_pciprobe,
+ .remove = __devexit_p(stl_pciremove)
+};
+
/*****************************************************************************/
/*
static int stl_getbrdstats(combrd_t __user *bp)
{
- stlbrd_t *brdp;
- stlpanel_t *panelp;
- int i;
+ combrd_t stl_brdstats;
+ struct stlbrd *brdp;
+ struct stlpanel *panelp;
+ unsigned int i;
if (copy_from_user(&stl_brdstats, bp, sizeof(combrd_t)))
return -EFAULT;
if (stl_brdstats.brd >= STL_MAXBRDS)
- return(-ENODEV);
+ return -ENODEV;
brdp = stl_brds[stl_brdstats.brd];
if (brdp == NULL)
- return(-ENODEV);
+ return -ENODEV;
memset(&stl_brdstats, 0, sizeof(combrd_t));
stl_brdstats.brd = brdp->brdnr;
stl_brdstats.irq = brdp->irq;
stl_brdstats.nrpanels = brdp->nrpanels;
stl_brdstats.nrports = brdp->nrports;
- for (i = 0; (i < brdp->nrpanels); i++) {
+ for (i = 0; i < brdp->nrpanels; i++) {
panelp = brdp->panels[i];
stl_brdstats.panels[i].panel = i;
stl_brdstats.panels[i].hwid = panelp->hwid;
* Resolve the referenced port number into a port struct pointer.
*/
-static stlport_t *stl_getport(int brdnr, int panelnr, int portnr)
+static struct stlport *stl_getport(int brdnr, int panelnr, int portnr)
{
- stlbrd_t *brdp;
- stlpanel_t *panelp;
+ struct stlbrd *brdp;
+ struct stlpanel *panelp;
- if ((brdnr < 0) || (brdnr >= STL_MAXBRDS))
- return(NULL);
+ if (brdnr < 0 || brdnr >= STL_MAXBRDS)
+ return NULL;
brdp = stl_brds[brdnr];
if (brdp == NULL)
- return(NULL);
- if ((panelnr < 0) || (panelnr >= brdp->nrpanels))
- return(NULL);
+ return NULL;
+ if (panelnr < 0 || (unsigned int)panelnr >= brdp->nrpanels)
+ return NULL;
panelp = brdp->panels[panelnr];
if (panelp == NULL)
- return(NULL);
- if ((portnr < 0) || (portnr >= panelp->nrports))
- return(NULL);
- return(panelp->ports[portnr]);
+ return NULL;
+ if (portnr < 0 || (unsigned int)portnr >= panelp->nrports)
+ return NULL;
+ return panelp->ports[portnr];
}
/*****************************************************************************/
* what port to get stats for (used through board control device).
*/
-static int stl_getportstats(stlport_t *portp, comstats_t __user *cp)
+static int stl_getportstats(struct stlport *portp, comstats_t __user *cp)
{
+ comstats_t stl_comstats;
unsigned char *head, *tail;
unsigned long flags;
portp = stl_getport(stl_comstats.brd, stl_comstats.panel,
stl_comstats.port);
if (portp == NULL)
- return(-ENODEV);
+ return -ENODEV;
}
portp->stats.state = portp->istate;
portp->stats.rxbuffered = 0;
spin_lock_irqsave(&stallion_lock, flags);
- if (portp->tty != NULL) {
+ if (portp->tty != NULL)
if (portp->tty->driver_data == portp) {
portp->stats.ttystate = portp->tty->flags;
/* No longer available as a statistic */
portp->stats.lflags = portp->tty->termios->c_lflag;
}
}
- }
spin_unlock_irqrestore(&stallion_lock, flags);
head = portp->tx.head;
tail = portp->tx.tail;
- portp->stats.txbuffered = ((head >= tail) ? (head - tail) :
- (STL_TXBUFSIZE - (tail - head)));
+ portp->stats.txbuffered = (head >= tail) ? (head - tail) :
+ (STL_TXBUFSIZE - (tail - head));
portp->stats.signals = (unsigned long) stl_getsignals(portp);
* Clear the port stats structure. We also return it zeroed out...
*/
-static int stl_clrportstats(stlport_t *portp, comstats_t __user *cp)
+static int stl_clrportstats(struct stlport *portp, comstats_t __user *cp)
{
+ comstats_t stl_comstats;
+
if (!portp) {
if (copy_from_user(&stl_comstats, cp, sizeof(comstats_t)))
return -EFAULT;
portp = stl_getport(stl_comstats.brd, stl_comstats.panel,
stl_comstats.port);
if (portp == NULL)
- return(-ENODEV);
+ return -ENODEV;
}
memset(&portp->stats, 0, sizeof(comstats_t));
* Return the entire driver ports structure to a user app.
*/
-static int stl_getportstruct(stlport_t __user *arg)
+static int stl_getportstruct(struct stlport __user *arg)
{
- stlport_t *portp;
+ struct stlport stl_dummyport;
+ struct stlport *portp;
- if (copy_from_user(&stl_dummyport, arg, sizeof(stlport_t)))
+ if (copy_from_user(&stl_dummyport, arg, sizeof(struct stlport)))
return -EFAULT;
portp = stl_getport(stl_dummyport.brdnr, stl_dummyport.panelnr,
stl_dummyport.portnr);
if (!portp)
return -ENODEV;
- return copy_to_user(arg, portp, sizeof(stlport_t)) ? -EFAULT : 0;
+ return copy_to_user(arg, portp, sizeof(struct stlport)) ? -EFAULT : 0;
}
/*****************************************************************************/
* Return the entire driver board structure to a user app.
*/
-static int stl_getbrdstruct(stlbrd_t __user *arg)
+static int stl_getbrdstruct(struct stlbrd __user *arg)
{
- stlbrd_t *brdp;
+ struct stlbrd stl_dummybrd;
+ struct stlbrd *brdp;
- if (copy_from_user(&stl_dummybrd, arg, sizeof(stlbrd_t)))
+ if (copy_from_user(&stl_dummybrd, arg, sizeof(struct stlbrd)))
return -EFAULT;
- if ((stl_dummybrd.brdnr < 0) || (stl_dummybrd.brdnr >= STL_MAXBRDS))
+ if (stl_dummybrd.brdnr >= STL_MAXBRDS)
return -ENODEV;
brdp = stl_brds[stl_dummybrd.brdnr];
if (!brdp)
- return(-ENODEV);
- return copy_to_user(arg, brdp, sizeof(stlbrd_t)) ? -EFAULT : 0;
+ return -ENODEV;
+ return copy_to_user(arg, brdp, sizeof(struct stlbrd)) ? -EFAULT : 0;
}
/*****************************************************************************/
brdnr = iminor(ip);
if (brdnr >= STL_MAXBRDS)
- return(-ENODEV);
+ return -ENODEV;
rc = 0;
switch (cmd) {
break;
}
- return(rc);
+ return rc;
}
static const struct tty_operations stl_ops = {
.tiocmset = stl_tiocmset,
};
-/*****************************************************************************/
-
-static int __init stl_init(void)
-{
- int i;
- printk(KERN_INFO "%s: version %s\n", stl_drvtitle, stl_drvversion);
-
- spin_lock_init(&stallion_lock);
- spin_lock_init(&brd_lock);
-
- stl_initbrds();
-
- stl_serial = alloc_tty_driver(STL_MAXBRDS * STL_MAXPORTS);
- if (!stl_serial)
- return -1;
-
-/*
- * Set up a character driver for per board stuff. This is mainly used
- * to do stats ioctls on the ports.
- */
- if (register_chrdev(STL_SIOMEMMAJOR, "staliomem", &stl_fsiomem))
- printk("STALLION: failed to register serial board device\n");
-
- stallion_class = class_create(THIS_MODULE, "staliomem");
- for (i = 0; i < 4; i++)
- class_device_create(stallion_class, NULL,
- MKDEV(STL_SIOMEMMAJOR, i), NULL,
- "staliomem%d", i);
-
- stl_serial->owner = THIS_MODULE;
- stl_serial->driver_name = stl_drvname;
- stl_serial->name = "ttyE";
- stl_serial->major = STL_SERIALMAJOR;
- stl_serial->minor_start = 0;
- stl_serial->type = TTY_DRIVER_TYPE_SERIAL;
- stl_serial->subtype = SERIAL_TYPE_NORMAL;
- stl_serial->init_termios = stl_deftermios;
- stl_serial->flags = TTY_DRIVER_REAL_RAW;
- tty_set_operations(stl_serial, &stl_ops);
-
- if (tty_register_driver(stl_serial)) {
- put_tty_driver(stl_serial);
- printk("STALLION: failed to register serial driver\n");
- return -1;
- }
-
- return 0;
-}
-
/*****************************************************************************/
/* CD1400 HARDWARE FUNCTIONS */
/*****************************************************************************/
* (Maybe should make this inline...)
*/
-static int stl_cd1400getreg(stlport_t *portp, int regnr)
+static int stl_cd1400getreg(struct stlport *portp, int regnr)
{
outb((regnr + portp->uartaddr), portp->ioaddr);
return inb(portp->ioaddr + EREG_DATA);
}
-static void stl_cd1400setreg(stlport_t *portp, int regnr, int value)
+static void stl_cd1400setreg(struct stlport *portp, int regnr, int value)
{
- outb((regnr + portp->uartaddr), portp->ioaddr);
+ outb(regnr + portp->uartaddr, portp->ioaddr);
outb(value, portp->ioaddr + EREG_DATA);
}
-static int stl_cd1400updatereg(stlport_t *portp, int regnr, int value)
+static int stl_cd1400updatereg(struct stlport *portp, int regnr, int value)
{
- outb((regnr + portp->uartaddr), portp->ioaddr);
+ outb(regnr + portp->uartaddr, portp->ioaddr);
if (inb(portp->ioaddr + EREG_DATA) != value) {
outb(value, portp->ioaddr + EREG_DATA);
return 1;
* identical when dealing with ports.
*/
-static int stl_cd1400panelinit(stlbrd_t *brdp, stlpanel_t *panelp)
+static int stl_cd1400panelinit(struct stlbrd *brdp, struct stlpanel *panelp)
{
unsigned int gfrcr;
int chipmask, i, j;
*/
chipmask = 0;
nrchips = panelp->nrports / CD1400_PORTS;
- for (i = 0; (i < nrchips); i++) {
+ for (i = 0; i < nrchips; i++) {
if (brdp->brdtype == BRD_ECHPCI) {
outb((panelp->pagenr + (i >> 1)), brdp->ioctrl);
ioaddr = panelp->iobase;
- } else {
+ } else
ioaddr = panelp->iobase + (EREG_BANKSIZE * (i >> 1));
- }
uartaddr = (i & 0x01) ? 0x080 : 0;
outb((GFRCR + uartaddr), ioaddr);
outb(0, (ioaddr + EREG_DATA));
outb(CCR_RESETFULL, (ioaddr + EREG_DATA));
outb(CCR_RESETFULL, (ioaddr + EREG_DATA));
outb((GFRCR + uartaddr), ioaddr);
- for (j = 0; (j < CCR_MAXWAIT); j++) {
+ for (j = 0; j < CCR_MAXWAIT; j++)
if ((gfrcr = inb(ioaddr + EREG_DATA)) != 0)
break;
- }
+
if ((j >= CCR_MAXWAIT) || (gfrcr < 0x40) || (gfrcr > 0x60)) {
printk("STALLION: cd1400 not responding, "
"brd=%d panel=%d chip=%d\n",
* Initialize hardware specific port registers.
*/
-static void stl_cd1400portinit(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp)
+static void stl_cd1400portinit(struct stlbrd *brdp, struct stlpanel *panelp, struct stlport *portp)
{
unsigned long flags;
pr_debug("stl_cd1400portinit(brdp=%p,panelp=%p,portp=%p)\n", brdp,
* since it won't usually take too long to be ready.
*/
-static void stl_cd1400ccrwait(stlport_t *portp)
+static void stl_cd1400ccrwait(struct stlport *portp)
{
int i;
- for (i = 0; (i < CCR_MAXWAIT); i++) {
- if (stl_cd1400getreg(portp, CCR) == 0) {
+ for (i = 0; i < CCR_MAXWAIT; i++)
+ if (stl_cd1400getreg(portp, CCR) == 0)
return;
- }
- }
printk("STALLION: cd1400 not responding, port=%d panel=%d brd=%d\n",
portp->portnr, portp->panelnr, portp->brdnr);
* settings.
*/
-static void stl_cd1400setport(stlport_t *portp, struct termios *tiosp)
+static void stl_cd1400setport(struct stlport *portp, struct ktermios *tiosp)
{
- stlbrd_t *brdp;
+ struct stlbrd *brdp;
unsigned long flags;
unsigned int clkdiv, baudrate;
unsigned char cor1, cor2, cor3;
baudrate = STL_CD1400MAXBAUD;
if (baudrate > 0) {
- for (clk = 0; (clk < CD1400_NUMCLKS); clk++) {
- clkdiv = ((portp->clk / stl_cd1400clkdivs[clk]) / baudrate);
+ for (clk = 0; clk < CD1400_NUMCLKS; clk++) {
+ clkdiv = (portp->clk / stl_cd1400clkdivs[clk]) / baudrate;
if (clkdiv < 0x100)
break;
}
mcor2 |= MCOR2_DCD;
sreron |= SRER_MODEM;
portp->flags |= ASYNC_CHECK_CD;
- } else {
+ } else
portp->flags &= ~ASYNC_CHECK_CD;
- }
/*
* Setup cd1400 enhanced modes if we can. In particular we want to
* Set the state of the DTR and RTS signals.
*/
-static void stl_cd1400setsignals(stlport_t *portp, int dtr, int rts)
+static void stl_cd1400setsignals(struct stlport *portp, int dtr, int rts)
{
unsigned char msvr1, msvr2;
unsigned long flags;
* Return the state of the signals.
*/
-static int stl_cd1400getsignals(stlport_t *portp)
+static int stl_cd1400getsignals(struct stlport *portp)
{
unsigned char msvr1, msvr2;
unsigned long flags;
* Enable/Disable the Transmitter and/or Receiver.
*/
-static void stl_cd1400enablerxtx(stlport_t *portp, int rx, int tx)
+static void stl_cd1400enablerxtx(struct stlport *portp, int rx, int tx)
{
unsigned char ccr;
unsigned long flags;
* Start/stop the Transmitter and/or Receiver.
*/
-static void stl_cd1400startrxtx(stlport_t *portp, int rx, int tx)
+static void stl_cd1400startrxtx(struct stlport *portp, int rx, int tx)
{
unsigned char sreron, sreroff;
unsigned long flags;
* Disable all interrupts from this port.
*/
-static void stl_cd1400disableintrs(stlport_t *portp)
+static void stl_cd1400disableintrs(struct stlport *portp)
{
unsigned long flags;
/*****************************************************************************/
-static void stl_cd1400sendbreak(stlport_t *portp, int len)
+static void stl_cd1400sendbreak(struct stlport *portp, int len)
{
unsigned long flags;
* Take flow control actions...
*/
-static void stl_cd1400flowctrl(stlport_t *portp, int state)
+static void stl_cd1400flowctrl(struct stlport *portp, int state)
{
struct tty_struct *tty;
unsigned long flags;
* Send a flow control character...
*/
-static void stl_cd1400sendflow(stlport_t *portp, int state)
+static void stl_cd1400sendflow(struct stlport *portp, int state)
{
struct tty_struct *tty;
unsigned long flags;
/*****************************************************************************/
-static void stl_cd1400flush(stlport_t *portp)
+static void stl_cd1400flush(struct stlport *portp)
{
unsigned long flags;
* maintains the busy port flag.
*/
-static int stl_cd1400datastate(stlport_t *portp)
+static int stl_cd1400datastate(struct stlport *portp)
{
pr_debug("stl_cd1400datastate(portp=%p)\n", portp);
* Interrupt service routine for cd1400 EasyIO boards.
*/
-static void stl_cd1400eiointr(stlpanel_t *panelp, unsigned int iobase)
+static void stl_cd1400eiointr(struct stlpanel *panelp, unsigned int iobase)
{
unsigned char svrtype;
* Interrupt service routine for cd1400 panels.
*/
-static void stl_cd1400echintr(stlpanel_t *panelp, unsigned int iobase)
+static void stl_cd1400echintr(struct stlpanel *panelp, unsigned int iobase)
{
unsigned char svrtype;
* this is the only way to generate them on the cd1400.
*/
-static inline int stl_cd1400breakisr(stlport_t *portp, int ioaddr)
+static int stl_cd1400breakisr(struct stlport *portp, int ioaddr)
{
if (portp->brklen == 1) {
outb((COR2 + portp->uartaddr), ioaddr);
* be NULL if the buffer has been freed.
*/
-static void stl_cd1400txisr(stlpanel_t *panelp, int ioaddr)
+static void stl_cd1400txisr(struct stlpanel *panelp, int ioaddr)
{
- stlport_t *portp;
+ struct stlport *portp;
int len, stlen;
char *head, *tail;
unsigned char ioack, srer;
}
outb(srer, (ioaddr + EREG_DATA));
} else {
- len = MIN(len, CD1400_TXFIFOSIZE);
+ len = min(len, CD1400_TXFIFOSIZE);
portp->stats.txtotal += len;
- stlen = MIN(len, ((portp->tx.buf + STL_TXBUFSIZE) - tail));
+ stlen = min(len, ((portp->tx.buf + STL_TXBUFSIZE) - tail));
outb((TDR + portp->uartaddr), ioaddr);
outsb((ioaddr + EREG_DATA), tail, stlen);
len -= stlen;
* shutdown a port not in user context. Need to handle this case.
*/
-static void stl_cd1400rxisr(stlpanel_t *panelp, int ioaddr)
+static void stl_cd1400rxisr(struct stlpanel *panelp, int ioaddr)
{
- stlport_t *portp;
+ struct stlport *portp;
struct tty_struct *tty;
unsigned int ioack, len, buflen;
unsigned char status;
outb((RDCR + portp->uartaddr), ioaddr);
len = inb(ioaddr + EREG_DATA);
if (tty == NULL || (buflen = tty_buffer_request_room(tty, len)) == 0) {
- len = MIN(len, sizeof(stl_unwanted));
+ len = min(len, sizeof(stl_unwanted));
outb((RDSR + portp->uartaddr), ioaddr);
insb((ioaddr + EREG_DATA), &stl_unwanted[0], len);
portp->stats.rxlost += len;
portp->stats.rxtotal += len;
} else {
- len = MIN(len, buflen);
+ len = min(len, buflen);
if (len > 0) {
unsigned char *ptr;
outb((RDSR + portp->uartaddr), ioaddr);
do_SAK(tty);
BRDENABLE(portp->brdnr, portp->pagenr);
}
- } else if (status & ST_PARITY) {
+ } else if (status & ST_PARITY)
status = TTY_PARITY;
- } else if (status & ST_FRAMING) {
+ else if (status & ST_FRAMING)
status = TTY_FRAME;
- } else if(status & ST_OVERRUN) {
+ else if(status & ST_OVERRUN)
status = TTY_OVERRUN;
- } else {
+ else
status = 0;
- }
- } else {
+ } else
status = 0;
- }
tty_insert_flip_char(tty, ch, status);
tty_schedule_flip(tty);
}
* processing routine.
*/
-static void stl_cd1400mdmisr(stlpanel_t *panelp, int ioaddr)
+static void stl_cd1400mdmisr(struct stlpanel *panelp, int ioaddr)
{
- stlport_t *portp;
+ struct stlport *portp;
unsigned int ioack;
unsigned char misr;
* (Maybe should make this inline...)
*/
-static int stl_sc26198getreg(stlport_t *portp, int regnr)
+static int stl_sc26198getreg(struct stlport *portp, int regnr)
{
outb((regnr | portp->uartaddr), (portp->ioaddr + XP_ADDR));
return inb(portp->ioaddr + XP_DATA);
}
-static void stl_sc26198setreg(stlport_t *portp, int regnr, int value)
+static void stl_sc26198setreg(struct stlport *portp, int regnr, int value)
{
outb((regnr | portp->uartaddr), (portp->ioaddr + XP_ADDR));
outb(value, (portp->ioaddr + XP_DATA));
}
-static int stl_sc26198updatereg(stlport_t *portp, int regnr, int value)
+static int stl_sc26198updatereg(struct stlport *portp, int regnr, int value)
{
outb((regnr | portp->uartaddr), (portp->ioaddr + XP_ADDR));
if (inb(portp->ioaddr + XP_DATA) != value) {
* Functions to get and set the sc26198 global registers.
*/
-static int stl_sc26198getglobreg(stlport_t *portp, int regnr)
+static int stl_sc26198getglobreg(struct stlport *portp, int regnr)
{
outb(regnr, (portp->ioaddr + XP_ADDR));
return inb(portp->ioaddr + XP_DATA);
}
#if 0
-static void stl_sc26198setglobreg(stlport_t *portp, int regnr, int value)
+static void stl_sc26198setglobreg(struct stlport *portp, int regnr, int value)
{
outb(regnr, (portp->ioaddr + XP_ADDR));
outb(value, (portp->ioaddr + XP_DATA));
* identical when dealing with ports.
*/
-static int stl_sc26198panelinit(stlbrd_t *brdp, stlpanel_t *panelp)
+static int stl_sc26198panelinit(struct stlbrd *brdp, struct stlpanel *panelp)
{
int chipmask, i;
int nrchips, ioaddr;
if (brdp->brdtype == BRD_ECHPCI)
outb(panelp->pagenr, brdp->ioctrl);
- for (i = 0; (i < nrchips); i++) {
+ for (i = 0; i < nrchips; i++) {
ioaddr = panelp->iobase + (i * 4);
outb(SCCR, (ioaddr + XP_ADDR));
outb(CR_RESETALL, (ioaddr + XP_DATA));
* Initialize hardware specific port registers.
*/
-static void stl_sc26198portinit(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp)
+static void stl_sc26198portinit(struct stlbrd *brdp, struct stlpanel *panelp, struct stlport *portp)
{
pr_debug("stl_sc26198portinit(brdp=%p,panelp=%p,portp=%p)\n", brdp,
panelp, portp);
* settings.
*/
-static void stl_sc26198setport(stlport_t *portp, struct termios *tiosp)
+static void stl_sc26198setport(struct stlport *portp, struct ktermios *tiosp)
{
- stlbrd_t *brdp;
+ struct stlbrd *brdp;
unsigned long flags;
unsigned int baudrate;
unsigned char mr0, mr1, mr2, clk;
mr1 |= (MR1_PARENB | MR1_PARODD);
else
mr1 |= (MR1_PARENB | MR1_PAREVEN);
- } else {
+ } else
mr1 |= MR1_PARNONE;
- }
mr1 |= MR1_ERRBLOCK;
if (baudrate > STL_SC26198MAXBAUD)
baudrate = STL_SC26198MAXBAUD;
- if (baudrate > 0) {
- for (clk = 0; (clk < SC26198_NRBAUDS); clk++) {
+ if (baudrate > 0)
+ for (clk = 0; clk < SC26198_NRBAUDS; clk++)
if (baudrate <= sc26198_baudtable[clk])
break;
- }
- }
/*
* Check what form of modem signaling is required and set it up.
if (tiosp->c_iflag & IXON) {
mr0 |= MR0_SWFTX | MR0_SWFT;
imron |= IR_XONXOFF;
- } else {
+ } else
imroff |= IR_XONXOFF;
- }
+
if (tiosp->c_iflag & IXOFF)
mr0 |= MR0_SWFRX;
* Set the state of the DTR and RTS signals.
*/
-static void stl_sc26198setsignals(stlport_t *portp, int dtr, int rts)
+static void stl_sc26198setsignals(struct stlport *portp, int dtr, int rts)
{
unsigned char iopioron, iopioroff;
unsigned long flags;
* Return the state of the signals.
*/
-static int stl_sc26198getsignals(stlport_t *portp)
+static int stl_sc26198getsignals(struct stlport *portp)
{
unsigned char ipr;
unsigned long flags;
* Enable/Disable the Transmitter and/or Receiver.
*/
-static void stl_sc26198enablerxtx(stlport_t *portp, int rx, int tx)
+static void stl_sc26198enablerxtx(struct stlport *portp, int rx, int tx)
{
unsigned char ccr;
unsigned long flags;
* Start/stop the Transmitter and/or Receiver.
*/
-static void stl_sc26198startrxtx(stlport_t *portp, int rx, int tx)
+static void stl_sc26198startrxtx(struct stlport *portp, int rx, int tx)
{
unsigned char imr;
unsigned long flags;
* Disable all interrupts from this port.
*/
-static void stl_sc26198disableintrs(stlport_t *portp)
+static void stl_sc26198disableintrs(struct stlport *portp)
{
unsigned long flags;
/*****************************************************************************/
-static void stl_sc26198sendbreak(stlport_t *portp, int len)
+static void stl_sc26198sendbreak(struct stlport *portp, int len)
{
unsigned long flags;
if (len == 1) {
stl_sc26198setreg(portp, SCCR, CR_TXSTARTBREAK);
portp->stats.txbreaks++;
- } else {
+ } else
stl_sc26198setreg(portp, SCCR, CR_TXSTOPBREAK);
- }
+
BRDDISABLE(portp->brdnr);
spin_unlock_irqrestore(&brd_lock, flags);
}
* Take flow control actions...
*/
-static void stl_sc26198flowctrl(stlport_t *portp, int state)
+static void stl_sc26198flowctrl(struct stlport *portp, int state)
{
struct tty_struct *tty;
unsigned long flags;
* Send a flow control character.
*/
-static void stl_sc26198sendflow(stlport_t *portp, int state)
+static void stl_sc26198sendflow(struct stlport *portp, int state)
{
struct tty_struct *tty;
unsigned long flags;
/*****************************************************************************/
-static void stl_sc26198flush(stlport_t *portp)
+static void stl_sc26198flush(struct stlport *portp)
{
unsigned long flags;
* check the port statusy register to be sure.
*/
-static int stl_sc26198datastate(stlport_t *portp)
+static int stl_sc26198datastate(struct stlport *portp)
{
unsigned long flags;
unsigned char sr;
* to process a command...
*/
-static void stl_sc26198wait(stlport_t *portp)
+static void stl_sc26198wait(struct stlport *portp)
{
int i;
if (portp == NULL)
return;
- for (i = 0; (i < 20); i++)
+ for (i = 0; i < 20; i++)
stl_sc26198getglobreg(portp, TSTR);
}
* automatic flow control modes of the sc26198.
*/
-static inline void stl_sc26198txunflow(stlport_t *portp, struct tty_struct *tty)
+static void stl_sc26198txunflow(struct stlport *portp, struct tty_struct *tty)
{
unsigned char mr0;
* Interrupt service routine for sc26198 panels.
*/
-static void stl_sc26198intr(stlpanel_t *panelp, unsigned int iobase)
+static void stl_sc26198intr(struct stlpanel *panelp, unsigned int iobase)
{
- stlport_t *portp;
+ struct stlport *portp;
unsigned int iack;
spin_lock(&brd_lock);
* be NULL if the buffer has been freed.
*/
-static void stl_sc26198txisr(stlport_t *portp)
+static void stl_sc26198txisr(struct stlport *portp)
{
unsigned int ioaddr;
unsigned char mr0;
outb(mr0, (ioaddr + XP_DATA));
}
} else {
- len = MIN(len, SC26198_TXFIFOSIZE);
+ len = min(len, SC26198_TXFIFOSIZE);
portp->stats.txtotal += len;
- stlen = MIN(len, ((portp->tx.buf + STL_TXBUFSIZE) - tail));
+ stlen = min(len, ((portp->tx.buf + STL_TXBUFSIZE) - tail));
outb(GTXFIFO, (ioaddr + XP_ADDR));
outsb((ioaddr + XP_DATA), tail, stlen);
len -= stlen;
* shutdown a port not in user context. Need to handle this case.
*/
-static void stl_sc26198rxisr(stlport_t *portp, unsigned int iack)
+static void stl_sc26198rxisr(struct stlport *portp, unsigned int iack)
{
struct tty_struct *tty;
unsigned int len, buflen, ioaddr;
if ((iack & IVR_TYPEMASK) == IVR_RXDATA) {
if (tty == NULL || (buflen = tty_buffer_request_room(tty, len)) == 0) {
- len = MIN(len, sizeof(stl_unwanted));
+ len = min(len, sizeof(stl_unwanted));
outb(GRXFIFO, (ioaddr + XP_ADDR));
insb((ioaddr + XP_DATA), &stl_unwanted[0], len);
portp->stats.rxlost += len;
portp->stats.rxtotal += len;
} else {
- len = MIN(len, buflen);
+ len = min(len, buflen);
if (len > 0) {
unsigned char *ptr;
outb(GRXFIFO, (ioaddr + XP_ADDR));
* Process an RX bad character.
*/
-static inline void stl_sc26198rxbadch(stlport_t *portp, unsigned char status, char ch)
+static void stl_sc26198rxbadch(struct stlport *portp, unsigned char status, char ch)
{
struct tty_struct *tty;
unsigned int ioaddr;
do_SAK(tty);
BRDENABLE(portp->brdnr, portp->pagenr);
}
- } else if (status & SR_RXPARITY) {
+ } else if (status & SR_RXPARITY)
status = TTY_PARITY;
- } else if (status & SR_RXFRAMING) {
+ else if (status & SR_RXFRAMING)
status = TTY_FRAME;
- } else if(status & SR_RXOVERRUN) {
+ else if(status & SR_RXOVERRUN)
status = TTY_OVERRUN;
- } else {
+ else
status = 0;
- }
- } else {
+ } else
status = 0;
- }
tty_insert_flip_char(tty, ch, status);
tty_schedule_flip(tty);
* the FIFO).
*/
-static void stl_sc26198rxbadchars(stlport_t *portp)
+static void stl_sc26198rxbadchars(struct stlport *portp)
{
unsigned char status, mr1;
char ch;
* processing time.
*/
-static void stl_sc26198otherisr(stlport_t *portp, unsigned int iack)
+static void stl_sc26198otherisr(struct stlport *portp, unsigned int iack)
{
unsigned char cir, ipr, xisr;
}
}
-/*****************************************************************************/
+static void stl_free_isabrds(void)
+{
+ struct stlbrd *brdp;
+ unsigned int i;
+
+ for (i = 0; i < stl_nrbrds; i++) {
+ if ((brdp = stl_brds[i]) == NULL || (brdp->state & STL_PROBED))
+ continue;
+
+ free_irq(brdp->irq, brdp);
+
+ stl_cleanup_panels(brdp);
+
+ release_region(brdp->ioaddr1, brdp->iosize1);
+ if (brdp->iosize2 > 0)
+ release_region(brdp->ioaddr2, brdp->iosize2);
+
+ kfree(brdp);
+ stl_brds[i] = NULL;
+ }
+}
+
+/*
+ * Loadable module initialization stuff.
+ */
+static int __init stallion_module_init(void)
+{
+ struct stlbrd *brdp;
+ struct stlconf conf;
+ unsigned int i, j;
+ int retval;
+
+ printk(KERN_INFO "%s: version %s\n", stl_drvtitle, stl_drvversion);
+
+ spin_lock_init(&stallion_lock);
+ spin_lock_init(&brd_lock);
+
+ stl_serial = alloc_tty_driver(STL_MAXBRDS * STL_MAXPORTS);
+ if (!stl_serial) {
+ retval = -ENOMEM;
+ goto err;
+ }
+
+ stl_serial->owner = THIS_MODULE;
+ stl_serial->driver_name = stl_drvname;
+ stl_serial->name = "ttyE";
+ stl_serial->major = STL_SERIALMAJOR;
+ stl_serial->minor_start = 0;
+ stl_serial->type = TTY_DRIVER_TYPE_SERIAL;
+ stl_serial->subtype = SERIAL_TYPE_NORMAL;
+ stl_serial->init_termios = stl_deftermios;
+ stl_serial->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+ tty_set_operations(stl_serial, &stl_ops);
+
+ retval = tty_register_driver(stl_serial);
+ if (retval) {
+ printk("STALLION: failed to register serial driver\n");
+ goto err_frtty;
+ }
+
+/*
+ * Find any dynamically supported boards. That is via module load
+ * line options.
+ */
+ for (i = stl_nrbrds; i < stl_nargs; i++) {
+ memset(&conf, 0, sizeof(conf));
+ if (stl_parsebrd(&conf, stl_brdsp[i]) == 0)
+ continue;
+ if ((brdp = stl_allocbrd()) == NULL)
+ continue;
+ brdp->brdnr = i;
+ brdp->brdtype = conf.brdtype;
+ brdp->ioaddr1 = conf.ioaddr1;
+ brdp->ioaddr2 = conf.ioaddr2;
+ brdp->irq = conf.irq;
+ brdp->irqtype = conf.irqtype;
+ stl_brds[brdp->brdnr] = brdp;
+ if (stl_brdinit(brdp)) {
+ stl_brds[brdp->brdnr] = NULL;
+ kfree(brdp);
+ } else {
+ for (j = 0; j < brdp->nrports; j++)
+ tty_register_device(stl_serial,
+ brdp->brdnr * STL_MAXPORTS + j, NULL);
+ stl_nrbrds = i + 1;
+ }
+ }
+
+ /* this has to be _after_ isa finding because of locking */
+ retval = pci_register_driver(&stl_pcidriver);
+ if (retval && stl_nrbrds == 0) {
+ printk(KERN_ERR "STALLION: can't register pci driver\n");
+ goto err_unrtty;
+ }
+
+/*
+ * Set up a character driver for per board stuff. This is mainly used
+ * to do stats ioctls on the ports.
+ */
+ if (register_chrdev(STL_SIOMEMMAJOR, "staliomem", &stl_fsiomem))
+ printk("STALLION: failed to register serial board device\n");
+
+ stallion_class = class_create(THIS_MODULE, "staliomem");
+ if (IS_ERR(stallion_class))
+ printk("STALLION: failed to create class\n");
+ for (i = 0; i < 4; i++)
+ class_device_create(stallion_class, NULL,
+ MKDEV(STL_SIOMEMMAJOR, i), NULL,
+ "staliomem%d", i);
+
+ return 0;
+err_unrtty:
+ tty_unregister_driver(stl_serial);
+err_frtty:
+ put_tty_driver(stl_serial);
+err:
+ return retval;
+}
+
+static void __exit stallion_module_exit(void)
+{
+ struct stlbrd *brdp;
+ unsigned int i, j;
+ int retval;
+
+ pr_debug("cleanup_module()\n");
+
+ printk(KERN_INFO "Unloading %s: version %s\n", stl_drvtitle,
+ stl_drvversion);
+
+/*
+ * Free up all allocated resources used by the ports. This includes
+ * memory and interrupts. As part of this process we will also do
+ * a hangup on every open port - to try to flush out any processes
+ * hanging onto ports.
+ */
+ for (i = 0; i < stl_nrbrds; i++) {
+ if ((brdp = stl_brds[i]) == NULL || (brdp->state & STL_PROBED))
+ continue;
+ for (j = 0; j < brdp->nrports; j++)
+ tty_unregister_device(stl_serial,
+ brdp->brdnr * STL_MAXPORTS + j);
+ }
+
+ for (i = 0; i < 4; i++)
+ class_device_destroy(stallion_class, MKDEV(STL_SIOMEMMAJOR, i));
+ if ((retval = unregister_chrdev(STL_SIOMEMMAJOR, "staliomem")))
+ printk("STALLION: failed to un-register serial memory device, "
+ "errno=%d\n", -retval);
+ class_destroy(stallion_class);
+
+ pci_unregister_driver(&stl_pcidriver);
+
+ stl_free_isabrds();
+
+ tty_unregister_driver(stl_serial);
+ put_tty_driver(stl_serial);
+}
+
+module_init(stallion_module_init);
+module_exit(stallion_module_exit);
+
+MODULE_AUTHOR("Greg Ungerer");
+MODULE_DESCRIPTION("Stallion Multiport Serial Driver");
+MODULE_LICENSE("GPL");