/* PCI related definitions */
-static unsigned short cy_pci_nboard;
-static unsigned short cy_isa_nboard;
-static unsigned short cy_nboard;
#ifdef CONFIG_PCI
static struct pci_device_id cy_pci_dev_id[] __devinitdata = {
{ PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Lo) }, /* PCI < 1Mb */
card_base_addr = cinfo->base_addr;
index = cinfo->bus_index;
+ /* card was not initialized yet (e.g. DEBUG_SHIRQ) */
+ if (unlikely(card_base_addr == NULL))
+ return IRQ_HANDLED;
+
/* This loop checks all chips in the card. Make a note whenever
_any_ chip had some work to do, as this is considered an
indication that there will be more to do. Only when no chip
*/
static void cy_wait_until_sent(struct tty_struct *tty, int timeout)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
void __iomem *base_addr;
int card, chip, channel, index;
unsigned long orig_jiffies;
*/
static void cy_close(struct tty_struct *tty, struct file *filp)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
unsigned long flags;
#ifdef CY_DEBUG_OTHER
*/
static int cy_write(struct tty_struct *tty, const unsigned char *buf, int count)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
unsigned long flags;
int c, ret = 0;
*/
static void cy_put_char(struct tty_struct *tty, unsigned char ch)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
unsigned long flags;
#ifdef CY_DEBUG_IO
*/
static void cy_flush_chars(struct tty_struct *tty)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
#ifdef CY_DEBUG_IO
printk("cyc:cy_flush_chars ttyC%d\n", info->line); /* */
*/
static int cy_write_room(struct tty_struct *tty)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
int ret;
#ifdef CY_DEBUG_IO
static int cy_chars_in_buffer(struct tty_struct *tty)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
int card, channel;
if (serial_paranoia_check(info, tty->name, "cy_chars_in_buffer"))
static int cy_tiocmget(struct tty_struct *tty, struct file *file)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
int card, chip, channel, index;
void __iomem *base_addr;
unsigned long flags;
((status & CyCTS) ? TIOCM_CTS : 0);
} else {
base_addr = cy_card[card].base_addr;
-
- if (cy_card[card].num_chips != -1) {
- return -EINVAL;
- }
-
firm_id = cy_card[card].base_addr + ID_ADDRESS;
if (ISZLOADED(cy_card[card])) {
zfw_ctrl = cy_card[card].base_addr +
cy_tiocmset(struct tty_struct *tty, struct file *file,
unsigned int set, unsigned int clear)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
int card, chip, channel, index;
void __iomem *base_addr;
unsigned long flags;
*/
static void cy_break(struct tty_struct *tty, int break_state)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
unsigned long flags;
if (serial_paranoia_check(info, tty->name, "cy_break"))
cy_ioctl(struct tty_struct *tty, struct file *file,
unsigned int cmd, unsigned long arg)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
struct cyclades_icount cprev, cnow; /* kernel counter temps */
struct serial_icounter_struct __user *p_cuser; /* user space */
int ret_val = 0;
case CYGETRTSDTR_INV:
ret_val = info->rtsdtr_inv;
break;
- case CYGETCARDINFO:
- if (copy_to_user(argp, &cy_card[info->card],
- sizeof(struct cyclades_card))) {
- ret_val = -EFAULT;
- break;
- }
- ret_val = 0;
- break;
case CYGETCD1400VER:
ret_val = info->chip_rev;
break;
*/
static void cy_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
#ifdef CY_DEBUG_OTHER
printk("cyc:cy_set_termios ttyC%d\n", info->line);
*/
static void cy_send_xchar(struct tty_struct *tty, char ch)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
int card, channel;
if (serial_paranoia_check(info, tty->name, "cy_send_xchar"))
*/
static void cy_throttle(struct tty_struct *tty)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
unsigned long flags;
void __iomem *base_addr;
int card, chip, channel, index;
*/
static void cy_unthrottle(struct tty_struct *tty)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
unsigned long flags;
void __iomem *base_addr;
int card, chip, channel, index;
static void cy_stop(struct tty_struct *tty)
{
struct cyclades_card *cinfo;
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
void __iomem *base_addr;
int chip, channel, index;
unsigned long flags;
static void cy_start(struct tty_struct *tty)
{
struct cyclades_card *cinfo;
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
void __iomem *base_addr;
int chip, channel, index;
unsigned long flags;
static void cy_flush_buffer(struct tty_struct *tty)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
int card, channel, retval;
unsigned long flags;
*/
static void cy_hangup(struct tty_struct *tty)
{
- struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
+ struct cyclades_port *info = tty->driver_data;
#ifdef CY_DEBUG_OTHER
printk("cyc:cy_hangup ttyC%d\n", info->line); /* */
* ---------------------------------------------------------------------
*/
+static void __devinit cy_init_card(struct cyclades_card *cinfo,
+ const unsigned int board)
+{
+ struct cyclades_port *info;
+ u32 mailbox;
+ unsigned int nports;
+ unsigned short chip_number;
+ int index, port;
+
+ if (IS_CYC_Z(*cinfo)) { /* Cyclades-Z */
+ mailbox = readl(&((struct RUNTIME_9060 __iomem *)
+ cinfo->ctl_addr)->mail_box_0);
+ nports = (mailbox == ZE_V1) ? ZE_V1_NPORTS : 8;
+ cinfo->intr_enabled = 0;
+ cinfo->nports = 0; /* Will be correctly set later, after
+ Z FW is loaded */
+ spin_lock_init(&cinfo->card_lock);
+ for (port = cinfo->first_line;
+ port < cinfo->first_line + nports; port++) {
+ info = &cy_port[port];
+ info->magic = CYCLADES_MAGIC;
+ info->type = PORT_STARTECH;
+ info->card = board;
+ info->line = port;
+ info->chip_rev = 0;
+ info->flags = STD_COM_FLAGS;
+ info->tty = NULL;
+ if (mailbox == ZO_V1)
+ info->xmit_fifo_size = CYZ_FIFO_SIZE;
+ else
+ info->xmit_fifo_size =
+ 4 * CYZ_FIFO_SIZE;
+ info->cor1 = 0;
+ info->cor2 = 0;
+ info->cor3 = 0;
+ info->cor4 = 0;
+ info->cor5 = 0;
+ info->tbpr = 0;
+ info->tco = 0;
+ info->rbpr = 0;
+ info->rco = 0;
+ info->custom_divisor = 0;
+ info->close_delay = 5 * HZ / 10;
+ info->closing_wait = CLOSING_WAIT_DELAY;
+ info->icount.cts = info->icount.dsr =
+ info->icount.rng = info->icount.dcd = 0;
+ info->icount.rx = info->icount.tx = 0;
+ info->icount.frame = info->icount.parity = 0;
+ info->icount.overrun = info->icount.brk = 0;
+ info->x_char = 0;
+ info->event = 0;
+ info->count = 0;
+ info->blocked_open = 0;
+ info->default_threshold = 0;
+ info->default_timeout = 0;
+ INIT_WORK(&info->tqueue, do_softint);
+ init_waitqueue_head(&info->open_wait);
+ init_waitqueue_head(&info->close_wait);
+ init_waitqueue_head(&info->shutdown_wait);
+ init_waitqueue_head(&info->delta_msr_wait);
+ /* info->session */
+ /* info->pgrp */
+ info->read_status_mask = 0;
+ /* info->timeout */
+ /* Bentson's vars */
+ info->jiffies[0] = 0;
+ info->jiffies[1] = 0;
+ info->jiffies[2] = 0;
+ info->rflush_count = 0;
+#ifdef CONFIG_CYZ_INTR
+ init_timer(&cyz_rx_full_timer[port]);
+ cyz_rx_full_timer[port].function = NULL;
+#endif
+ }
+#ifndef CONFIG_CYZ_INTR
+ if (!timer_pending(&cyz_timerlist)) {
+ mod_timer(&cyz_timerlist, jiffies + 1);
+#ifdef CY_PCI_DEBUG
+ printk("Cyclades-Z polling initialized\n");
+#endif
+ }
+#endif /* CONFIG_CYZ_INTR */
+
+ } else { /* Cyclom-Y of some kind */
+ index = cinfo->bus_index;
+ spin_lock_init(&cinfo->card_lock);
+ cinfo->nports = CyPORTS_PER_CHIP * cinfo->num_chips;
+ for (port = cinfo->first_line;
+ port < cinfo->first_line + cinfo->nports; port++) {
+ info = &cy_port[port];
+ info->magic = CYCLADES_MAGIC;
+ info->type = PORT_CIRRUS;
+ info->card = board;
+ info->line = port;
+ info->flags = STD_COM_FLAGS;
+ info->tty = NULL;
+ info->xmit_fifo_size = CyMAX_CHAR_FIFO;
+ info->cor1 =
+ CyPARITY_NONE | Cy_1_STOP | Cy_8_BITS;
+ info->cor2 = CyETC;
+ info->cor3 = 0x08; /* _very_ small rcv threshold */
+ info->cor4 = 0;
+ info->cor5 = 0;
+ info->custom_divisor = 0;
+ info->close_delay = 5 * HZ / 10;
+ info->closing_wait = CLOSING_WAIT_DELAY;
+ info->icount.cts = info->icount.dsr =
+ info->icount.rng = info->icount.dcd = 0;
+ info->icount.rx = info->icount.tx = 0;
+ info->icount.frame = info->icount.parity = 0;
+ info->icount.overrun = info->icount.brk = 0;
+ chip_number = (port - cinfo->first_line) / 4;
+ if ((info->chip_rev =
+ readb(cinfo->base_addr +
+ (cy_chip_offset[chip_number] <<
+ index) + (CyGFRCR << index))) >=
+ CD1400_REV_J) {
+ /* It is a CD1400 rev. J or later */
+ info->tbpr = baud_bpr_60[13]; /* Tx BPR */
+ info->tco = baud_co_60[13]; /* Tx CO */
+ info->rbpr = baud_bpr_60[13]; /* Rx BPR */
+ info->rco = baud_co_60[13]; /* Rx CO */
+ info->rflow = 0;
+ info->rtsdtr_inv = 1;
+ } else {
+ info->tbpr = baud_bpr_25[13]; /* Tx BPR */
+ info->tco = baud_co_25[13]; /* Tx CO */
+ info->rbpr = baud_bpr_25[13]; /* Rx BPR */
+ info->rco = baud_co_25[13]; /* Rx CO */
+ info->rflow = 0;
+ info->rtsdtr_inv = 0;
+ }
+ info->x_char = 0;
+ info->event = 0;
+ info->count = 0;
+ info->blocked_open = 0;
+ info->default_threshold = 0;
+ info->default_timeout = 0;
+ INIT_WORK(&info->tqueue, do_softint);
+ init_waitqueue_head(&info->open_wait);
+ init_waitqueue_head(&info->close_wait);
+ init_waitqueue_head(&info->shutdown_wait);
+ init_waitqueue_head(&info->delta_msr_wait);
+ /* info->session */
+ /* info->pgrp */
+ info->read_status_mask =
+ CyTIMEOUT | CySPECHAR | CyBREAK
+ | CyPARITY | CyFRAME | CyOVERRUN;
+ /* info->timeout */
+ }
+ }
+}
+
/* initialize chips on Cyclom-Y card -- return number of valid
chips (which is number of ports/4) */
static unsigned short __init
cy_card[j].bus_index = 0;
cy_card[j].first_line = cy_next_channel;
cy_card[j].num_chips = cy_isa_nchan / 4;
+ cy_init_card(&cy_card[j], j);
nboard++;
/* print message */
cy_isa_irq);
printk("%d channels starting from port %d.\n",
cy_isa_nchan, cy_next_channel);
+ for (j = cy_next_channel;
+ j < cy_next_channel + cy_isa_nchan; j++)
+ tty_register_device(cy_serial_driver, j, NULL);
cy_next_channel += cy_isa_nchan;
}
return nboard;
#endif /* CONFIG_ISA */
} /* cy_detect_isa */
-static void plx_init(void __iomem * addr, __u32 initctl)
+#ifdef CONFIG_PCI
+static void __devinit plx_init(void __iomem * addr, __u32 initctl)
{
/* Reset PLX */
cy_writel(addr + initctl, readl(addr + initctl) | 0x40000000);
cy_writel(addr + initctl, readl(addr + initctl) & ~0x20000000);
}
-/*
- * ---------------------------------------------------------------------
- * cy_detect_pci() - Test PCI bus presence and Cyclom-Ye/PCI.
- * sets global variables and return the number of PCI boards found.
- * ---------------------------------------------------------------------
- */
-static int __init cy_detect_pci(void)
+static int __devinit cy_init_Ze(unsigned long cy_pci_phys0,
+ unsigned long cy_pci_phys2,
+ struct RUNTIME_9060 __iomem *cy_pci_addr0,
+ int cy_pci_irq, struct pci_dev *pdev)
{
-#ifdef CONFIG_PCI
+ void __iomem *cy_pci_addr2;
+ unsigned int j;
+ unsigned short cy_pci_nchan;
- struct pci_dev *pdev = NULL;
- unsigned char cyy_rev_id;
- unsigned char cy_pci_irq = 0;
- __u32 cy_pci_phys0, cy_pci_phys2;
- void __iomem *cy_pci_addr0, *cy_pci_addr2;
- unsigned short i, j, cy_pci_nchan, plx_ver;
- unsigned short device_id, dev_index = 0;
- __u32 mailbox;
- __u32 ZeIndex = 0;
- void __iomem *Ze_addr0[NR_CARDS], *Ze_addr2[NR_CARDS];
- __u32 Ze_phys0[NR_CARDS], Ze_phys2[NR_CARDS];
- unsigned char Ze_irq[NR_CARDS];
- struct pci_dev *Ze_pdev[NR_CARDS];
+ cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Ze_win);
- for (i = 0; i < NR_CARDS; i++) {
- /* look for a Cyclades card by vendor and device id */
- while ((device_id = cy_pci_dev_id[dev_index].device) != 0) {
- if ((pdev = pci_get_device(PCI_VENDOR_ID_CYCLADES,
- device_id, pdev)) == NULL) {
- dev_index++; /* try next device id */
- } else {
- break; /* found a board */
- }
- }
+ readl(&cy_pci_addr0->mail_box_0);
+#ifdef CY_PCI_DEBUG
+ printk("Cyclades-Z/PCI: relocate winaddr=0x%lx ctladdr=0x%lx\n",
+ (ulong)cy_pci_addr2, (ulong)cy_pci_addr0);
+ printk("Cyclades-Z/PCI: New Cyclades-Z board. FPGA not "
+ "loaded\n");
+#endif
+ /* This must be the new Cyclades-Ze/PCI. */
+ cy_pci_nchan = ZE_V1_NPORTS;
+
+ if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) {
+ printk("Cyclades-Ze/PCI found at 0x%lx but no channels "
+ "are available.\nChange NR_PORTS in cyclades.c "
+ "and recompile kernel.\n",
+ (ulong) cy_pci_phys2);
+ return -EIO;
+ }
- if (device_id == 0)
+ /* fill the next cy_card structure available */
+ for (j = 0; j < NR_CARDS; j++) {
+ if (cy_card[j].base_addr == 0)
break;
+ }
+ if (j == NR_CARDS) { /* no more cy_cards available */
+ printk("Cyclades-Ze/PCI found at 0x%lx but no more "
+ "cards can be used.\nChange NR_CARDS in "
+ "cyclades.c and recompile kernel.\n",
+ (ulong) cy_pci_phys2);
+ return -EIO;
+ }
+#ifdef CONFIG_CYZ_INTR
+ /* allocate IRQ only if board has an IRQ */
+ if ((cy_pci_irq != 0) && (cy_pci_irq != 255)) {
+ if (request_irq(cy_pci_irq, cyz_interrupt,
+ IRQF_SHARED, "Cyclades-Z",
+ &cy_card[j])) {
+ printk("Cyclom-Ze/PCI found at 0x%lx ",
+ (ulong) cy_pci_phys2);
+ printk("but could not allocate IRQ%d.\n",
+ cy_pci_irq);
+ return -EIO;
+ }
+ }
+#endif /* CONFIG_CYZ_INTR */
- if (pci_enable_device(pdev))
- continue;
+ /* set cy_card */
+ cy_card[j].base_addr = cy_pci_addr2;
+ cy_card[j].ctl_addr = cy_pci_addr0;
+ cy_card[j].irq = (int)cy_pci_irq;
+ cy_card[j].bus_index = 1;
+ cy_card[j].first_line = cy_next_channel;
+ cy_card[j].num_chips = -1;
+ cy_init_card(&cy_card[j], j);
+ pci_set_drvdata(pdev, &cy_card[j]);
+
+ /* print message */
+#ifdef CONFIG_CYZ_INTR
+ /* don't report IRQ if board is no IRQ */
+ if ((cy_pci_irq != 0) && (cy_pci_irq != 255))
+ printk("Cyclades-Ze/PCI #%d: 0x%lx-0x%lx, IRQ%d, ",
+ j + 1, (ulong) cy_pci_phys2,
+ (ulong) (cy_pci_phys2 + CyPCI_Ze_win - 1),
+ (int)cy_pci_irq);
+ else
+#endif /* CONFIG_CYZ_INTR */
+ printk("Cyclades-Ze/PCI #%d: 0x%lx-0x%lx, ",
+ j + 1, (ulong) cy_pci_phys2,
+ (ulong) (cy_pci_phys2 + CyPCI_Ze_win - 1));
- /* read PCI configuration area */
- cy_pci_irq = pdev->irq;
- cy_pci_phys0 = pci_resource_start(pdev, 0);
- cy_pci_phys2 = pci_resource_start(pdev, 2);
- pci_read_config_byte(pdev, PCI_REVISION_ID, &cyy_rev_id);
+ printk("%d channels starting from port %d.\n",
+ cy_pci_nchan, cy_next_channel);
+ for (j = cy_next_channel; j < cy_next_channel + cy_pci_nchan; j++)
+ tty_register_device(cy_serial_driver, j, &pdev->dev);
+ cy_next_channel += cy_pci_nchan;
- device_id &= ~PCI_DEVICE_ID_MASK;
+ return 0;
+}
- if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
- device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
+static int __devinit cy_pci_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ unsigned char cyy_rev_id;
+ unsigned char cy_pci_irq;
+ __u32 cy_pci_phys0, cy_pci_phys2, mailbox;
+ void __iomem *cy_pci_addr0, *cy_pci_addr2;
+ unsigned int device_id;
+ unsigned short j, cy_pci_nchan, plx_ver;
+ int retval;
+
+ retval = pci_enable_device(pdev);
+ if (retval) {
+ dev_err(&pdev->dev, "cannot enable device\n");
+ return retval;
+ }
+
+ /* read PCI configuration area */
+ cy_pci_irq = pdev->irq;
+ cy_pci_phys0 = pci_resource_start(pdev, 0);
+ cy_pci_phys2 = pci_resource_start(pdev, 2);
+ pci_read_config_byte(pdev, PCI_REVISION_ID, &cyy_rev_id);
+
+ device_id = pdev->device & ~PCI_DEVICE_ID_MASK;
+
+ if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
+ device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
#ifdef CY_PCI_DEBUG
+ printk("Cyclom-Y/PCI (bus=0x0%x, pci_id=0x%x, ",
+ pdev->bus->number, pdev->devfn);
+ printk("rev_id=%d) IRQ%d\n",
+ cyy_rev_id, (int)cy_pci_irq);
+ printk("Cyclom-Y/PCI:found winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (ulong)cy_pci_phys2, (ulong)cy_pci_phys0);
+#endif
+
+ if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
+ printk(" Warning: PCI I/O bit incorrectly "
+ "set. Ignoring it...\n");
+ pdev->resource[2].flags &= ~IORESOURCE_IO;
+ }
+
+ /* Although we don't use this I/O region, we should
+ request it from the kernel anyway, to avoid problems
+ with other drivers accessing it. */
+ retval = pci_request_regions(pdev, "Cyclom-Y");
+ if (retval) {
+ printk(KERN_ERR "cyclades: failed to reserve "
+ "PCI resources\n");
+ return retval;
+ }
+#if defined(__alpha__)
+ if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo) { /* below 1M? */
printk("Cyclom-Y/PCI (bus=0x0%x, pci_id=0x%x, ",
pdev->bus->number, pdev->devfn);
printk("rev_id=%d) IRQ%d\n",
cyy_rev_id, (int)cy_pci_irq);
printk("Cyclom-Y/PCI:found winaddr=0x%lx "
"ctladdr=0x%lx\n",
- (ulong)cy_pci_phys2, (ulong)cy_pci_phys0);
-#endif
-
- if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
- printk(" Warning: PCI I/O bit incorrectly "
- "set. Ignoring it...\n");
- pdev->resource[2].flags &= ~IORESOURCE_IO;
- }
-
- /* Although we don't use this I/O region, we should
- request it from the kernel anyway, to avoid problems
- with other drivers accessing it. */
- if (pci_request_regions(pdev, "Cyclom-Y") != 0) {
- printk(KERN_ERR "cyclades: failed to reserve "
- "PCI resources\n");
- continue;
- }
-#if defined(__alpha__)
- if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo) { /* below 1M? */
- printk("Cyclom-Y/PCI (bus=0x0%x, pci_id=0x%x, ",
- pdev->bus->number, pdev->devfn);
- printk("rev_id=%d) IRQ%d\n",
- cyy_rev_id, (int)cy_pci_irq);
- printk("Cyclom-Y/PCI:found winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (ulong)cy_pci_phys2,
- (ulong)cy_pci_phys0);
- printk("Cyclom-Y/PCI not supported for low "
- "addresses in Alpha systems.\n");
- i--;
- continue;
- }
+ (ulong)cy_pci_phys2,
+ (ulong)cy_pci_phys0);
+ printk("Cyclom-Y/PCI not supported for low "
+ "addresses in Alpha systems.\n");
+ return -EIO;
+ }
#endif
- cy_pci_addr0 = ioremap(cy_pci_phys0, CyPCI_Yctl);
- cy_pci_addr2 = ioremap(cy_pci_phys2, CyPCI_Ywin);
+ cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Yctl);
+ cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Ywin);
#ifdef CY_PCI_DEBUG
- printk("Cyclom-Y/PCI: relocate winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (u_long)cy_pci_addr2, (u_long)cy_pci_addr0);
+ printk("Cyclom-Y/PCI: relocate winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (u_long)cy_pci_addr2, (u_long)cy_pci_addr0);
#endif
- cy_pci_nchan = (unsigned short)(CyPORTS_PER_CHIP *
- cyy_init_card(cy_pci_addr2, 1));
- if (cy_pci_nchan == 0) {
- printk("Cyclom-Y PCI host card with ");
- printk("no Serial-Modules at 0x%lx.\n",
- (ulong) cy_pci_phys2);
- i--;
- continue;
- }
- if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) {
- printk("Cyclom-Y/PCI found at 0x%lx ",
- (ulong) cy_pci_phys2);
- printk("but no channels are available.\n");
- printk("Change NR_PORTS in cyclades.c and "
- "recompile kernel.\n");
- return i;
- }
- /* fill the next cy_card structure available */
- for (j = 0; j < NR_CARDS; j++) {
- if (cy_card[j].base_addr == 0)
- break;
- }
- if (j == NR_CARDS) { /* no more cy_cards available */
- printk("Cyclom-Y/PCI found at 0x%lx ",
- (ulong) cy_pci_phys2);
- printk("but no more cards can be used.\n");
- printk("Change NR_CARDS in cyclades.c and "
- "recompile kernel.\n");
- return i;
- }
-
- /* allocate IRQ */
- if (request_irq(cy_pci_irq, cyy_interrupt,
- IRQF_SHARED, "Cyclom-Y", &cy_card[j])) {
- printk("Cyclom-Y/PCI found at 0x%lx ",
- (ulong) cy_pci_phys2);
- printk("but could not allocate IRQ%d.\n",
- cy_pci_irq);
- return i;
- }
-
- /* set cy_card */
- cy_card[j].base_phys = (ulong) cy_pci_phys2;
- cy_card[j].ctl_phys = (ulong) cy_pci_phys0;
- cy_card[j].base_addr = cy_pci_addr2;
- cy_card[j].ctl_addr = cy_pci_addr0;
- cy_card[j].irq = (int)cy_pci_irq;
- cy_card[j].bus_index = 1;
- cy_card[j].first_line = cy_next_channel;
- cy_card[j].num_chips = cy_pci_nchan / 4;
- cy_card[j].pdev = pdev;
-
- /* enable interrupts in the PCI interface */
- plx_ver = readb(cy_pci_addr2 + CyPLX_VER) & 0x0f;
- switch (plx_ver) {
- case PLX_9050:
-
- cy_writeb(cy_pci_addr0 + 0x4c, 0x43);
+ cy_pci_nchan = (unsigned short)(CyPORTS_PER_CHIP *
+ cyy_init_card(cy_pci_addr2, 1));
+ if (cy_pci_nchan == 0) {
+ printk("Cyclom-Y PCI host card with ");
+ printk("no Serial-Modules at 0x%lx.\n",
+ (ulong) cy_pci_phys2);
+ return -EIO;
+ }
+ if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) {
+ printk("Cyclom-Y/PCI found at 0x%lx ",
+ (ulong) cy_pci_phys2);
+ printk("but no channels are available.\n");
+ printk("Change NR_PORTS in cyclades.c and "
+ "recompile kernel.\n");
+ return -EIO;
+ }
+ /* fill the next cy_card structure available */
+ for (j = 0; j < NR_CARDS; j++) {
+ if (cy_card[j].base_addr == 0)
break;
+ }
+ if (j == NR_CARDS) { /* no more cy_cards available */
+ printk("Cyclom-Y/PCI found at 0x%lx ",
+ (ulong) cy_pci_phys2);
+ printk("but no more cards can be used.\n");
+ printk("Change NR_CARDS in cyclades.c and "
+ "recompile kernel.\n");
+ return -EIO;
+ }
- case PLX_9060:
- case PLX_9080:
- default: /* Old boards, use PLX_9060 */
-
- plx_init(cy_pci_addr0, 0x6c);
- /* For some yet unknown reason, once the PLX9060 reloads
- the EEPROM, the IRQ is lost and, thus, we have to
- re-write it to the PCI config. registers.
- This will remain here until we find a permanent
- fix. */
- pci_write_config_byte(pdev, PCI_INTERRUPT_LINE,
- cy_pci_irq);
-
- cy_writew(cy_pci_addr0 + 0x68,
- readw(cy_pci_addr0 + 0x68) | 0x0900);
- break;
- }
+ /* allocate IRQ */
+ retval = request_irq(cy_pci_irq, cyy_interrupt,
+ IRQF_SHARED, "Cyclom-Y", &cy_card[j]);
+ if (retval) {
+ printk("Cyclom-Y/PCI found at 0x%lx ",
+ (ulong) cy_pci_phys2);
+ printk("but could not allocate IRQ%d.\n",
+ cy_pci_irq);
+ return retval;
+ }
- /* print message */
- printk("Cyclom-Y/PCI #%d: 0x%lx-0x%lx, IRQ%d, ",
- j + 1, (ulong)cy_pci_phys2,
- (ulong) (cy_pci_phys2 + CyPCI_Ywin - 1),
- (int)cy_pci_irq);
- printk("%d channels starting from port %d.\n",
- cy_pci_nchan, cy_next_channel);
+ /* set cy_card */
+ cy_card[j].base_addr = cy_pci_addr2;
+ cy_card[j].ctl_addr = cy_pci_addr0;
+ cy_card[j].irq = (int)cy_pci_irq;
+ cy_card[j].bus_index = 1;
+ cy_card[j].first_line = cy_next_channel;
+ cy_card[j].num_chips = cy_pci_nchan / 4;
+ cy_init_card(&cy_card[j], j);
+ pci_set_drvdata(pdev, &cy_card[j]);
- cy_next_channel += cy_pci_nchan;
- } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Lo) {
- /* print message */
- printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ",
- pdev->bus->number, pdev->devfn);
- printk("rev_id=%d) IRQ%d\n",
- cyy_rev_id, (int)cy_pci_irq);
- printk("Cyclades-Z/PCI: found winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (ulong)cy_pci_phys2, (ulong)cy_pci_phys0);
- printk("Cyclades-Z/PCI not supported for low "
- "addresses\n");
+ /* enable interrupts in the PCI interface */
+ plx_ver = readb(cy_pci_addr2 + CyPLX_VER) & 0x0f;
+ switch (plx_ver) {
+ case PLX_9050:
+
+ cy_writeb(cy_pci_addr0 + 0x4c, 0x43);
break;
- } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) {
-#ifdef CY_PCI_DEBUG
- printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ",
- pdev->bus->number, pdev->devfn);
- printk("rev_id=%d) IRQ%d\n",
- cyy_rev_id, (int)cy_pci_irq);
- printk("Cyclades-Z/PCI: found winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (ulong) cy_pci_phys2, (ulong) cy_pci_phys0);
-#endif
- cy_pci_addr0 = ioremap(cy_pci_phys0, CyPCI_Zctl);
- /* Disable interrupts on the PLX before resetting it */
- cy_writew(cy_pci_addr0 + 0x68,
- readw(cy_pci_addr0 + 0x68) & ~0x0900);
+ case PLX_9060:
+ case PLX_9080:
+ default: /* Old boards, use PLX_9060 */
plx_init(cy_pci_addr0, 0x6c);
- /* For some yet unknown reason, once the PLX9060 reloads
- the EEPROM, the IRQ is lost and, thus, we have to
- re-write it to the PCI config. registers.
- This will remain here until we find a permanent
- fix. */
+ /* For some yet unknown reason, once the PLX9060 reloads
+ the EEPROM, the IRQ is lost and, thus, we have to
+ re-write it to the PCI config. registers.
+ This will remain here until we find a permanent
+ fix. */
pci_write_config_byte(pdev, PCI_INTERRUPT_LINE,
- cy_pci_irq);
-
- mailbox = (__u32)readl(&((struct RUNTIME_9060 __iomem *)
- cy_pci_addr0)->mail_box_0);
-
- if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
- printk(" Warning: PCI I/O bit incorrectly "
- "set. Ignoring it...\n");
- pdev->resource[2].flags &= ~IORESOURCE_IO;
- }
+ cy_pci_irq);
- /* Although we don't use this I/O region, we should
- request it from the kernel anyway, to avoid problems
- with other drivers accessing it. */
- if (pci_request_regions(pdev, "Cyclades-Z") != 0) {
- printk(KERN_ERR "cyclades: failed to reserve "
- "PCI resources\n");
- continue;
- }
+ cy_writew(cy_pci_addr0 + 0x68,
+ readw(cy_pci_addr0 + 0x68) | 0x0900);
+ break;
+ }
- if (mailbox == ZE_V1) {
- cy_pci_addr2 = ioremap(cy_pci_phys2,
- CyPCI_Ze_win);
- if (ZeIndex == NR_CARDS) {
- printk("Cyclades-Ze/PCI found at "
- "0x%lx but no more cards can "
- "be used.\nChange NR_CARDS in "
- "cyclades.c and recompile "
- "kernel.\n",
- (ulong)cy_pci_phys2);
- } else {
- Ze_phys0[ZeIndex] = cy_pci_phys0;
- Ze_phys2[ZeIndex] = cy_pci_phys2;
- Ze_addr0[ZeIndex] = cy_pci_addr0;
- Ze_addr2[ZeIndex] = cy_pci_addr2;
- Ze_irq[ZeIndex] = cy_pci_irq;
- Ze_pdev[ZeIndex] = pdev;
- ZeIndex++;
- }
- i--;
- continue;
- } else {
- cy_pci_addr2 = ioremap(cy_pci_phys2,CyPCI_Zwin);
- }
+ /* print message */
+ printk("Cyclom-Y/PCI #%d: 0x%lx-0x%lx, IRQ%d, ",
+ j + 1, (ulong)cy_pci_phys2,
+ (ulong) (cy_pci_phys2 + CyPCI_Ywin - 1),
+ (int)cy_pci_irq);
+ printk("%d channels starting from port %d.\n",
+ cy_pci_nchan, cy_next_channel);
+ for (j = cy_next_channel;
+ j < cy_next_channel + cy_pci_nchan; j++)
+ tty_register_device(cy_serial_driver, j, &pdev->dev);
+ cy_next_channel += cy_pci_nchan;
+ } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Lo) {
+ /* print message */
+ printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ",
+ pdev->bus->number, pdev->devfn);
+ printk("rev_id=%d) IRQ%d\n",
+ cyy_rev_id, (int)cy_pci_irq);
+ printk("Cyclades-Z/PCI: found winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (ulong)cy_pci_phys2, (ulong)cy_pci_phys0);
+ printk("Cyclades-Z/PCI not supported for low "
+ "addresses\n");
+ return -EIO;
+ } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) {
#ifdef CY_PCI_DEBUG
- printk("Cyclades-Z/PCI: relocate winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (ulong) cy_pci_addr2, (ulong) cy_pci_addr0);
- if (mailbox == ZO_V1) {
- cy_writel(&((struct RUNTIME_9060 *)
- (cy_pci_addr0))->loc_addr_base,
- WIN_CREG);
- printk("Cyclades-8Zo/PCI: FPGA id %lx, ver "
- "%lx\n", (ulong) (0xff &
- readl(&((struct CUSTOM_REG *)
- (cy_pci_addr2))->fpga_id)),
- (ulong)(0xff &
- readl(&((struct CUSTOM_REG *)
- (cy_pci_addr2))->
- fpga_version)));
- cy_writel(&((struct RUNTIME_9060 *)
- (cy_pci_addr0))->loc_addr_base,
- WIN_RAM);
- } else {
- printk("Cyclades-Z/PCI: New Cyclades-Z board. "
- "FPGA not loaded\n");
- }
+ printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ",
+ pdev->bus->number, pdev->devfn);
+ printk("rev_id=%d) IRQ%d\n",
+ cyy_rev_id, (int)cy_pci_irq);
+ printk("Cyclades-Z/PCI: found winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (ulong) cy_pci_phys2, (ulong) cy_pci_phys0);
#endif
- /* The following clears the firmware id word. This
- ensures that the driver will not attempt to talk to
- the board until it has been properly initialized.
- */
- if ((mailbox == ZO_V1) || (mailbox == ZO_V2))
- cy_writel(cy_pci_addr2 + ID_ADDRESS, 0L);
-
- /* This must be a Cyclades-8Zo/PCI. The extendable
- version will have a different device_id and will
- be allocated its maximum number of ports. */
- cy_pci_nchan = 8;
-
- if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) {
- printk("Cyclades-8Zo/PCI found at 0x%lx but"
- "no channels are available.\nChange "
- "NR_PORTS in cyclades.c and recompile "
- "kernel.\n", (ulong)cy_pci_phys2);
- return i;
- }
+ cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Zctl);
+
+ /* Disable interrupts on the PLX before resetting it */
+ cy_writew(cy_pci_addr0 + 0x68,
+ readw(cy_pci_addr0 + 0x68) & ~0x0900);
+
+ plx_init(cy_pci_addr0, 0x6c);
+ /* For some yet unknown reason, once the PLX9060 reloads
+ the EEPROM, the IRQ is lost and, thus, we have to
+ re-write it to the PCI config. registers.
+ This will remain here until we find a permanent
+ fix. */
+ pci_write_config_byte(pdev, PCI_INTERRUPT_LINE,
+ cy_pci_irq);
- /* fill the next cy_card structure available */
- for (j = 0; j < NR_CARDS; j++) {
- if (cy_card[j].base_addr == 0)
- break;
- }
- if (j == NR_CARDS) { /* no more cy_cards available */
- printk("Cyclades-8Zo/PCI found at 0x%lx but"
- "no more cards can be used.\nChange "
- "NR_CARDS in cyclades.c and recompile "
- "kernel.\n", (ulong)cy_pci_phys2);
- return i;
- }
-#ifdef CONFIG_CYZ_INTR
- /* allocate IRQ only if board has an IRQ */
- if ((cy_pci_irq != 0) && (cy_pci_irq != 255)) {
- if (request_irq(cy_pci_irq, cyz_interrupt,
- IRQF_SHARED, "Cyclades-Z",
- &cy_card[j])) {
- printk("Cyclom-8Zo/PCI found at 0x%lx "
- "but could not allocate "
- "IRQ%d.\n", (ulong)cy_pci_phys2,
- cy_pci_irq);
- return i;
- }
- }
-#endif /* CONFIG_CYZ_INTR */
+ mailbox = (__u32)readl(&((struct RUNTIME_9060 __iomem *)
+ cy_pci_addr0)->mail_box_0);
- /* set cy_card */
- cy_card[j].base_phys = cy_pci_phys2;
- cy_card[j].ctl_phys = cy_pci_phys0;
- cy_card[j].base_addr = cy_pci_addr2;
- cy_card[j].ctl_addr = cy_pci_addr0;
- cy_card[j].irq = (int)cy_pci_irq;
- cy_card[j].bus_index = 1;
- cy_card[j].first_line = cy_next_channel;
- cy_card[j].num_chips = -1;
- cy_card[j].pdev = pdev;
-
- /* print message */
-#ifdef CONFIG_CYZ_INTR
- /* don't report IRQ if board is no IRQ */
- if ((cy_pci_irq != 0) && (cy_pci_irq != 255))
- printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, "
- "IRQ%d, ", j + 1, (ulong)cy_pci_phys2,
- (ulong) (cy_pci_phys2 + CyPCI_Zwin - 1),
- (int)cy_pci_irq);
- else
-#endif /* CONFIG_CYZ_INTR */
- printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, ",
- j + 1, (ulong)cy_pci_phys2,
- (ulong)(cy_pci_phys2 + CyPCI_Zwin - 1));
+ if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
+ printk(" Warning: PCI I/O bit incorrectly "
+ "set. Ignoring it...\n");
+ pdev->resource[2].flags &= ~IORESOURCE_IO;
+ }
- printk("%d channels starting from port %d.\n",
- cy_pci_nchan, cy_next_channel);
- cy_next_channel += cy_pci_nchan;
+ /* Although we don't use this I/O region, we should
+ request it from the kernel anyway, to avoid problems
+ with other drivers accessing it. */
+ retval = pci_request_regions(pdev, "Cyclades-Z");
+ if (retval) {
+ printk(KERN_ERR "cyclades: failed to reserve "
+ "PCI resources\n");
+ return retval;
}
- }
- for (; ZeIndex != 0 && i < NR_CARDS; i++) {
- cy_pci_phys0 = Ze_phys0[0];
- cy_pci_phys2 = Ze_phys2[0];
- cy_pci_addr0 = Ze_addr0[0];
- cy_pci_addr2 = Ze_addr2[0];
- cy_pci_irq = Ze_irq[0];
- pdev = Ze_pdev[0];
- for (j = 0; j < ZeIndex - 1; j++) {
- Ze_phys0[j] = Ze_phys0[j + 1];
- Ze_phys2[j] = Ze_phys2[j + 1];
- Ze_addr0[j] = Ze_addr0[j + 1];
- Ze_addr2[j] = Ze_addr2[j + 1];
- Ze_irq[j] = Ze_irq[j + 1];
- Ze_pdev[j] = Ze_pdev[j + 1];
+ if (mailbox == ZE_V1) {
+ retval = cy_init_Ze(cy_pci_phys0, cy_pci_phys2,
+ cy_pci_addr0, cy_pci_irq, pdev);
+ return retval;
+ } else {
+ cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Zwin);
}
- ZeIndex--;
- mailbox = (__u32)readl(&((struct RUNTIME_9060 __iomem *)
- cy_pci_addr0)->mail_box_0);
+
#ifdef CY_PCI_DEBUG
- printk("Cyclades-Z/PCI: relocate winaddr=0x%lx ctladdr=0x%lx\n",
- (ulong)cy_pci_addr2, (ulong)cy_pci_addr0);
- printk("Cyclades-Z/PCI: New Cyclades-Z board. FPGA not "
- "loaded\n");
+ printk("Cyclades-Z/PCI: relocate winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (ulong) cy_pci_addr2, (ulong) cy_pci_addr0);
+ if (mailbox == ZO_V1) {
+ cy_writel(&((struct RUNTIME_9060 *)
+ (cy_pci_addr0))->loc_addr_base,
+ WIN_CREG);
+ printk("Cyclades-8Zo/PCI: FPGA id %lx, ver "
+ "%lx\n", (ulong) (0xff &
+ readl(&((struct CUSTOM_REG *)
+ (cy_pci_addr2))->fpga_id)),
+ (ulong)(0xff &
+ readl(&((struct CUSTOM_REG *)
+ (cy_pci_addr2))->
+ fpga_version)));
+ cy_writel(&((struct RUNTIME_9060 *)
+ (cy_pci_addr0))->loc_addr_base,
+ WIN_RAM);
+ } else {
+ printk("Cyclades-Z/PCI: New Cyclades-Z board. "
+ "FPGA not loaded\n");
+ }
#endif
- /* This must be the new Cyclades-Ze/PCI. */
- cy_pci_nchan = ZE_V1_NPORTS;
+ /* The following clears the firmware id word. This
+ ensures that the driver will not attempt to talk to
+ the board until it has been properly initialized.
+ */
+ if ((mailbox == ZO_V1) || (mailbox == ZO_V2))
+ cy_writel(cy_pci_addr2 + ID_ADDRESS, 0L);
+
+ /* This must be a Cyclades-8Zo/PCI. The extendable
+ version will have a different device_id and will
+ be allocated its maximum number of ports. */
+ cy_pci_nchan = 8;
if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) {
- printk("Cyclades-Ze/PCI found at 0x%lx but no channels "
- "are available.\nChange NR_PORTS in cyclades.c "
- "and recompile kernel.\n",
- (ulong) cy_pci_phys2);
- return i;
+ printk("Cyclades-8Zo/PCI found at 0x%lx but"
+ "no channels are available.\nChange "
+ "NR_PORTS in cyclades.c and recompile "
+ "kernel.\n", (ulong)cy_pci_phys2);
+ return -EIO;
}
/* fill the next cy_card structure available */
break;
}
if (j == NR_CARDS) { /* no more cy_cards available */
- printk("Cyclades-Ze/PCI found at 0x%lx but no more "
- "cards can be used.\nChange NR_CARDS in "
- "cyclades.c and recompile kernel.\n",
- (ulong) cy_pci_phys2);
- return i;
+ printk("Cyclades-8Zo/PCI found at 0x%lx but"
+ "no more cards can be used.\nChange "
+ "NR_CARDS in cyclades.c and recompile "
+ "kernel.\n", (ulong)cy_pci_phys2);
+ return -EIO;
}
#ifdef CONFIG_CYZ_INTR
/* allocate IRQ only if board has an IRQ */
if ((cy_pci_irq != 0) && (cy_pci_irq != 255)) {
- if (request_irq(cy_pci_irq, cyz_interrupt,
+ retval = request_irq(cy_pci_irq, cyz_interrupt,
IRQF_SHARED, "Cyclades-Z",
- &cy_card[j])) {
- printk("Cyclom-Ze/PCI found at 0x%lx ",
- (ulong) cy_pci_phys2);
- printk("but could not allocate IRQ%d.\n",
+ &cy_card[j]);
+ if (retval) {
+ printk("Cyclom-8Zo/PCI found at 0x%lx "
+ "but could not allocate "
+ "IRQ%d.\n", (ulong)cy_pci_phys2,
cy_pci_irq);
- return i;
+ return retval;
}
}
#endif /* CONFIG_CYZ_INTR */
/* set cy_card */
- cy_card[j].base_phys = cy_pci_phys2;
- cy_card[j].ctl_phys = cy_pci_phys0;
cy_card[j].base_addr = cy_pci_addr2;
cy_card[j].ctl_addr = cy_pci_addr0;
cy_card[j].irq = (int)cy_pci_irq;
cy_card[j].bus_index = 1;
cy_card[j].first_line = cy_next_channel;
cy_card[j].num_chips = -1;
- cy_card[j].pdev = pdev;
+ cy_init_card(&cy_card[j], j);
+ pci_set_drvdata(pdev, &cy_card[j]);
/* print message */
#ifdef CONFIG_CYZ_INTR
/* don't report IRQ if board is no IRQ */
if ((cy_pci_irq != 0) && (cy_pci_irq != 255))
- printk("Cyclades-Ze/PCI #%d: 0x%lx-0x%lx, IRQ%d, ",
- j + 1, (ulong) cy_pci_phys2,
- (ulong) (cy_pci_phys2 + CyPCI_Ze_win - 1),
+ printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, "
+ "IRQ%d, ", j + 1, (ulong)cy_pci_phys2,
+ (ulong) (cy_pci_phys2 + CyPCI_Zwin - 1),
(int)cy_pci_irq);
else
#endif /* CONFIG_CYZ_INTR */
- printk("Cyclades-Ze/PCI #%d: 0x%lx-0x%lx, ",
- j + 1, (ulong) cy_pci_phys2,
- (ulong) (cy_pci_phys2 + CyPCI_Ze_win - 1));
+ printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, ",
+ j + 1, (ulong)cy_pci_phys2,
+ (ulong)(cy_pci_phys2 + CyPCI_Zwin - 1));
printk("%d channels starting from port %d.\n",
- cy_pci_nchan, cy_next_channel);
+ cy_pci_nchan, cy_next_channel);
+ for (j = cy_next_channel;
+ j < cy_next_channel + cy_pci_nchan; j++)
+ tty_register_device(cy_serial_driver, j, &pdev->dev);
cy_next_channel += cy_pci_nchan;
}
- if (ZeIndex != 0) {
- printk("Cyclades-Ze/PCI found at 0x%x but no more cards can be "
- "used.\nChange NR_CARDS in cyclades.c and recompile "
- "kernel.\n", (unsigned int)Ze_phys2[0]);
- }
- return i;
-#else
+
return 0;
-#endif /* ifdef CONFIG_PCI */
-} /* cy_detect_pci */
+}
+
+static void __devexit cy_pci_remove(struct pci_dev *pdev)
+{
+ struct cyclades_card *cinfo = pci_get_drvdata(pdev);
+ unsigned int i;
+
+ /* non-Z with old PLX */
+ if (!IS_CYC_Z(*cinfo) && (readb(cinfo->base_addr + CyPLX_VER) & 0x0f) ==
+ PLX_9050)
+ cy_writeb(cinfo->ctl_addr + 0x4c, 0);
+ else
+#ifndef CONFIG_CYZ_INTR
+ if (!IS_CYC_Z(*cinfo))
+#endif
+ cy_writew(cinfo->ctl_addr + 0x68,
+ readw(cinfo->ctl_addr + 0x68) & ~0x0900);
+
+ pci_iounmap(pdev, cinfo->base_addr);
+ if (cinfo->ctl_addr)
+ pci_iounmap(pdev, cinfo->ctl_addr);
+ if (cinfo->irq
+#ifndef CONFIG_CYZ_INTR
+ && !IS_CYC_Z(*cinfo)
+#endif /* CONFIG_CYZ_INTR */
+ )
+ free_irq(cinfo->irq, cinfo);
+ pci_release_regions(pdev);
+
+ cinfo->base_addr = NULL;
+ for (i = cinfo->first_line; i < cinfo->first_line + cinfo->nports; i++){
+ cy_port[i].line = -1;
+ cy_port[i].magic = -1;
+ }
+ for (i = cinfo->first_line; i < cinfo->first_line +
+ cinfo->nports; i++)
+ tty_unregister_device(cy_serial_driver, i);
+}
+
+static struct pci_driver cy_pci_driver = {
+ .name = "cyclades",
+ .id_table = cy_pci_dev_id,
+ .probe = cy_pci_probe,
+ .remove = __devexit_p(cy_pci_remove)
+};
+#endif
/*
* This routine prints out the appropriate serial driver version number
static int __init cy_init(void)
{
- struct cyclades_port *info;
- struct cyclades_card *cinfo;
- int number_z_boards = 0;
- int board, port, i, index;
- unsigned long mailbox;
- unsigned short chip_number;
- int nports;
+ unsigned int i, nboards;
+ int retval = -ENOMEM;
cy_serial_driver = alloc_tty_driver(NR_PORTS);
if (!cy_serial_driver)
- return -ENOMEM;
+ goto err;
show_version();
/* Initialize the tty_driver structure */
cy_serial_driver->init_termios = tty_std_termios;
cy_serial_driver->init_termios.c_cflag =
B9600 | CS8 | CREAD | HUPCL | CLOCAL;
- cy_serial_driver->flags = TTY_DRIVER_REAL_RAW;
+ cy_serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
tty_set_operations(cy_serial_driver, &cy_ops);
- if (tty_register_driver(cy_serial_driver))
- panic("Couldn't register Cyclades serial driver\n");
+ retval = tty_register_driver(cy_serial_driver);
+ if (retval) {
+ printk(KERN_ERR "Couldn't register Cyclades serial driver\n");
+ goto err_frtty;
+ }
for (i = 0; i < NR_CARDS; i++) {
/* base_addr=0 indicates board not found */
cy_card[i].base_addr = NULL;
}
+ /* invalidate remaining cy_port structures */
+ for (i = 0; i < NR_PORTS; i++) {
+ cy_port[i].line = -1;
+ cy_port[i].magic = -1;
+ }
+
/* the code below is responsible to find the boards. Each different
type of board has its own detection routine. If a board is found,
the next cy_card structure available is set by the detection
the cy_next_channel. */
/* look for isa boards */
- cy_isa_nboard = cy_detect_isa();
+ nboards = cy_detect_isa();
+#ifdef CONFIG_PCI
/* look for pci boards */
- cy_pci_nboard = cy_detect_pci();
-
- cy_nboard = cy_isa_nboard + cy_pci_nboard;
-
- /* invalidate remaining cy_card structures */
- for (i = 0; i < NR_CARDS; i++) {
- if (cy_card[i].base_addr == 0) {
- cy_card[i].first_line = -1;
- cy_card[i].ctl_addr = NULL;
- cy_card[i].irq = 0;
- cy_card[i].bus_index = 0;
- cy_card[i].first_line = 0;
- cy_card[i].num_chips = 0;
- }
- }
- /* invalidate remaining cy_port structures */
- for (i = cy_next_channel; i < NR_PORTS; i++) {
- cy_port[i].line = -1;
- cy_port[i].magic = -1;
- }
-
- /* initialize per-port data structures for each valid board found */
- for (board = 0; board < cy_nboard; board++) {
- cinfo = &cy_card[board];
- if (cinfo->num_chips == -1) { /* Cyclades-Z */
- number_z_boards++;
- mailbox = readl(&((struct RUNTIME_9060 __iomem *)
- cy_card[board].ctl_addr)->
- mail_box_0);
- nports = (mailbox == ZE_V1) ? ZE_V1_NPORTS : 8;
- cinfo->intr_enabled = 0;
- cinfo->nports = 0; /* Will be correctly set later, after
- Z FW is loaded */
- spin_lock_init(&cinfo->card_lock);
- for (port = cinfo->first_line;
- port < cinfo->first_line + nports; port++) {
- info = &cy_port[port];
- info->magic = CYCLADES_MAGIC;
- info->type = PORT_STARTECH;
- info->card = board;
- info->line = port;
- info->chip_rev = 0;
- info->flags = STD_COM_FLAGS;
- info->tty = NULL;
- if (mailbox == ZO_V1)
- info->xmit_fifo_size = CYZ_FIFO_SIZE;
- else
- info->xmit_fifo_size =
- 4 * CYZ_FIFO_SIZE;
- info->cor1 = 0;
- info->cor2 = 0;
- info->cor3 = 0;
- info->cor4 = 0;
- info->cor5 = 0;
- info->tbpr = 0;
- info->tco = 0;
- info->rbpr = 0;
- info->rco = 0;
- info->custom_divisor = 0;
- info->close_delay = 5 * HZ / 10;
- info->closing_wait = CLOSING_WAIT_DELAY;
- info->icount.cts = info->icount.dsr =
- info->icount.rng = info->icount.dcd = 0;
- info->icount.rx = info->icount.tx = 0;
- info->icount.frame = info->icount.parity = 0;
- info->icount.overrun = info->icount.brk = 0;
- info->x_char = 0;
- info->event = 0;
- info->count = 0;
- info->blocked_open = 0;
- info->default_threshold = 0;
- info->default_timeout = 0;
- INIT_WORK(&info->tqueue, do_softint);
- init_waitqueue_head(&info->open_wait);
- init_waitqueue_head(&info->close_wait);
- init_waitqueue_head(&info->shutdown_wait);
- init_waitqueue_head(&info->delta_msr_wait);
- /* info->session */
- /* info->pgrp */
- info->read_status_mask = 0;
- /* info->timeout */
- /* Bentson's vars */
- info->jiffies[0] = 0;
- info->jiffies[1] = 0;
- info->jiffies[2] = 0;
- info->rflush_count = 0;
-#ifdef CONFIG_CYZ_INTR
- init_timer(&cyz_rx_full_timer[port]);
- cyz_rx_full_timer[port].function = NULL;
+ retval = pci_register_driver(&cy_pci_driver);
+ if (retval && !nboards)
+ goto err_unr;
#endif
- }
- continue;
- } else { /* Cyclom-Y of some kind */
- index = cinfo->bus_index;
- spin_lock_init(&cinfo->card_lock);
- cinfo->nports = CyPORTS_PER_CHIP * cinfo->num_chips;
- for (port = cinfo->first_line;
- port < cinfo->first_line + cinfo->nports; port++) {
- info = &cy_port[port];
- info->magic = CYCLADES_MAGIC;
- info->type = PORT_CIRRUS;
- info->card = board;
- info->line = port;
- info->flags = STD_COM_FLAGS;
- info->tty = NULL;
- info->xmit_fifo_size = CyMAX_CHAR_FIFO;
- info->cor1 =
- CyPARITY_NONE | Cy_1_STOP | Cy_8_BITS;
- info->cor2 = CyETC;
- info->cor3 = 0x08; /* _very_ small rcv threshold */
- info->cor4 = 0;
- info->cor5 = 0;
- info->custom_divisor = 0;
- info->close_delay = 5 * HZ / 10;
- info->closing_wait = CLOSING_WAIT_DELAY;
- info->icount.cts = info->icount.dsr =
- info->icount.rng = info->icount.dcd = 0;
- info->icount.rx = info->icount.tx = 0;
- info->icount.frame = info->icount.parity = 0;
- info->icount.overrun = info->icount.brk = 0;
- chip_number = (port - cinfo->first_line) / 4;
- if ((info->chip_rev =
- readb(cinfo->base_addr +
- (cy_chip_offset[chip_number] <<
- index) + (CyGFRCR << index))) >=
- CD1400_REV_J) {
- /* It is a CD1400 rev. J or later */
- info->tbpr = baud_bpr_60[13]; /* Tx BPR */
- info->tco = baud_co_60[13]; /* Tx CO */
- info->rbpr = baud_bpr_60[13]; /* Rx BPR */
- info->rco = baud_co_60[13]; /* Rx CO */
- info->rflow = 0;
- info->rtsdtr_inv = 1;
- } else {
- info->tbpr = baud_bpr_25[13]; /* Tx BPR */
- info->tco = baud_co_25[13]; /* Tx CO */
- info->rbpr = baud_bpr_25[13]; /* Rx BPR */
- info->rco = baud_co_25[13]; /* Rx CO */
- info->rflow = 0;
- info->rtsdtr_inv = 0;
- }
- info->x_char = 0;
- info->event = 0;
- info->count = 0;
- info->blocked_open = 0;
- info->default_threshold = 0;
- info->default_timeout = 0;
- INIT_WORK(&info->tqueue, do_softint);
- init_waitqueue_head(&info->open_wait);
- init_waitqueue_head(&info->close_wait);
- init_waitqueue_head(&info->shutdown_wait);
- init_waitqueue_head(&info->delta_msr_wait);
- /* info->session */
- /* info->pgrp */
- info->read_status_mask =
- CyTIMEOUT | CySPECHAR | CyBREAK
- | CyPARITY | CyFRAME | CyOVERRUN;
- /* info->timeout */
- }
- }
- }
-
-#ifndef CONFIG_CYZ_INTR
- if (number_z_boards) {
- mod_timer(&cyz_timerlist, jiffies + 1);
-#ifdef CY_PCI_DEBUG
- printk("Cyclades-Z polling initialized\n");
-#endif
- }
-#endif /* CONFIG_CYZ_INTR */
return 0;
-
+err_unr:
+ tty_unregister_driver(cy_serial_driver);
+err_frtty:
+ put_tty_driver(cy_serial_driver);
+err:
+ return retval;
} /* cy_init */
static void __exit cy_cleanup_module(void)
put_tty_driver(cy_serial_driver);
+#ifdef CONFIG_PCI
+ pci_unregister_driver(&cy_pci_driver);
+#endif
+
for (i = 0; i < NR_CARDS; i++) {
if (cy_card[i].base_addr) {
+ /* clear interrupt */
+ cy_writeb(cy_card[i].base_addr + Cy_ClrIntr, 0);
iounmap(cy_card[i].base_addr);
if (cy_card[i].ctl_addr)
iounmap(cy_card[i].ctl_addr);
if (cy_card[i].irq
#ifndef CONFIG_CYZ_INTR
- && cy_card[i].num_chips != -1 /* not a Z card */
+ && !IS_CYC_Z(cy_card[i])
#endif /* CONFIG_CYZ_INTR */
)
free_irq(cy_card[i].irq, &cy_card[i]);
-#ifdef CONFIG_PCI
- if (cy_card[i].pdev)
- pci_release_regions(cy_card[i].pdev);
-#endif
+ for (e1 = cy_card[i].first_line;
+ e1 < cy_card[i].first_line +
+ cy_card[i].nports; e1++)
+ tty_unregister_device(cy_serial_driver, e1);
}
}
} /* cy_cleanup_module */