If you have an Alchemy AU1000 processor (MIPS based) and you want
to use a console on a serial port, say Y. Otherwise, say N.
-config QTRONIX_KEYBOARD
- bool "Enable Qtronix 990P Keyboard Support"
- depends on IT8712
- help
- Images of Qtronix keyboards are at
- <http://www.qtronix.com/keyboard.html>.
-
-config IT8172_CIR
- bool
- depends on QTRONIX_KEYBOARD
- default y
-
-config IT8172_SCR0
- bool "Enable Smart Card Reader 0 Support "
- depends on IT8712
- help
- Say Y here to support smart-card reader 0 (SCR0) on the Integrated
- Technology Express, Inc. ITE8172 SBC. Vendor page at
- <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
- board at <http://www.mvista.com/partners/semiconductor/ite.html>.
-
-config IT8172_SCR1
- bool "Enable Smart Card Reader 1 Support "
- depends on IT8712
- help
- Say Y here to support smart-card reader 1 (SCR1) on the Integrated
- Technology Express, Inc. ITE8172 SBC. Vendor page at
- <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
- board at <http://www.mvista.com/partners/semiconductor/ite.html>.
-
config A2232
tristate "Commodore A2232 serial support (EXPERIMENTAL)"
depends on EXPERIMENTAL && ZORRO && BROKEN_ON_SMP
When not in use, each legacy PTY occupies 12 bytes on 32-bit
architectures and 24 bytes on 64-bit architectures.
+config BRIQ_PANEL
+ tristate 'Total Impact briQ front panel driver'
+ depends on PPC_CHRP
+ ---help---
+ The briQ is a small footprint CHRP computer with a frontpanel VFD, a
+ tristate led and two switches. It is the size of a CDROM drive.
+
+ If you have such one and want anything showing on the VFD then you
+ must answer Y here.
+
+ To compile this driver as a module, choose M here: the
+ module will be called briq_panel.
+
+ It's safe to say N here.
+
config PRINTER
tristate "Parallel printer support"
depends on PARPORT
console. This driver allows each pSeries partition to have a console
which is accessed via the HMC.
+config HVC_ISERIES
+ bool "iSeries Hypervisor Virtual Console support"
+ depends on PPC_ISERIES && !VIOCONS
+ select HVC_DRIVER
+ help
+ iSeries machines support a hypervisor virtual console.
+
config HVC_RTAS
bool "IBM RTAS Console support"
depends on PPC_RTAS
config RTC
tristate "Enhanced Real Time Clock Support"
- depends on !PPC && !PARISC && !IA64 && !M68K && (!SPARC || PCI) && !FRV && !ARM
+ depends on !PPC && !PARISC && !IA64 && !M68K && (!SPARC || PCI) && !FRV && !ARM && !SUPERH
---help---
If you say Y here and create a character special file /dev/rtc with
major number 10 and minor number 135 using mknod ("man mknod"), you
will get access to the real time clock (or hardware clock) built
into your computer.
-config S3C2410_RTC
- bool "S3C2410 RTC Driver"
- depends on ARCH_S3C2410
- help
- RTC (Realtime Clock) driver for the clock inbuilt into the
- Samsung S3C2410. This can provide periodic interrupt rates
- from 1Hz to 64Hz for user programs, and wakeup from Alarm.
-
config COBALT_LCD
bool "Support for Cobalt LCD"
depends on MIPS_COBALT
config RAW_DRIVER
tristate "RAW driver (/dev/raw/rawN) (OBSOLETE)"
+ depends on BLOCK
help
The raw driver permits block devices to be bound to /dev/raw/rawN.
Once bound, I/O against /dev/raw/rawN uses efficient zero-copy I/O.
help
If you say Y here, you will have a miscdevice named "/dev/hpet/". Each
open selects one of the timers supported by the HPET. The timers are
- non-periodioc and/or periodic.
+ non-periodic and/or periodic.
config HPET_RTC_IRQ
bool "HPET Control RTC IRQ" if !HPET_EMULATE_RTC
config TELCLOCK
tristate "Telecom clock driver for MPBL0010 ATCA SBC"
- depends on EXPERIMENTAL
+ depends on EXPERIMENTAL && X86
default n
help
The telecom clock device is specific to the MPBL0010 ATCA computer and