u8 rev_max;
u16 flags;
} via_isa_bridges[] = {
+ { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
* Cable special cases
*/
-static struct dmi_system_id cable_dmi_table[] = {
+static const struct dmi_system_id cable_dmi_table[] = {
{
.ident = "Acer Ferrari 3400",
.matches = {
if ((config->flags & VIA_UDMA) < VIA_UDMA_66)
return ATA_CBL_PATA40;
/* UDMA 66 chips have only drive side logic */
- else if((config->flags & VIA_UDMA) < VIA_UDMA_100)
+ else if ((config->flags & VIA_UDMA) < VIA_UDMA_100)
return ATA_CBL_PATA_UNK;
/* UDMA 100 or later */
pci_read_config_dword(pdev, 0x50, &ata66);
two drives */
if (ata66 & (0x10100000 >> (16 * ap->port_no)))
return ATA_CBL_PATA80;
+ /* Check with ACPI so we can spot BIOS reported SATA bridges */
+ if (ata_acpi_cbl_80wire(ap))
+ return ATA_CBL_PATA80;
return ATA_CBL_PATA40;
}
-static int via_pre_reset(struct ata_port *ap, unsigned long deadline)
+static int via_pre_reset(struct ata_link *link, unsigned long deadline)
{
+ struct ata_port *ap = link->ap;
const struct via_isa_bridge *config = ap->host->private_data;
if (!(config->flags & VIA_NO_ENABLES)) {
return -ENOENT;
}
- return ata_std_prereset(ap, deadline);
+ return ata_std_prereset(link, deadline);
}
int ut;
int offset = 3 - (2*ap->port_no) - adev->devno;
-
/* Calculate the timing values we require */
ata_timing_compute(adev, mode, &t, T, UT);
ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 9) - 2)) : 0x07;
break;
}
+
/* Set UDMA unless device is not UDMA capable */
- if (udma_type)
- pci_write_config_byte(pdev, 0x50 + offset, ut);
+ if (udma_type) {
+ u8 cable80_status;
+
+ /* Get 80-wire cable detection bit */
+ pci_read_config_byte(pdev, 0x50 + offset, &cable80_status);
+ cable80_status &= 0x10;
+
+ pci_write_config_byte(pdev, 0x50 + offset, ut | cable80_status);
+ }
}
static void via_set_piomode(struct ata_port *ap, struct ata_device *adev)
};
static struct ata_port_operations via_port_ops = {
- .port_disable = ata_port_disable,
.set_piomode = via_set_piomode,
.set_dmamode = via_set_dmamode,
.mode_filter = ata_pci_default_filter,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .irq_ack = ata_irq_ack,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
static struct ata_port_operations via_port_ops_noirq = {
- .port_disable = ata_port_disable,
.set_piomode = via_set_piomode,
.set_dmamode = via_set_dmamode,
.mode_filter = ata_pci_default_filter,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .irq_ack = ata_irq_ack,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
/**
* @pdev: PCI device
* @flags: configuration flags
*
- * Set the FIFO properties for this device if neccessary. Used both on
+ * Set the FIFO properties for this device if necessary. Used both on
* set up and on and the resume path
*/