#define DRV_NAME "pata_it821x"
-#define DRV_VERSION "0.3.7"
+#define DRV_VERSION "0.3.8"
struct it821x_dev
{
/*
* We allow users to force the card into non raid mode without
- * flashing the alternative BIOS. This is also neccessary right now
+ * flashing the alternative BIOS. This is also necessary right now
* for embedded platforms that cannot run a PC BIOS but are using this
* device.
*/
* @ap: ATA port
* @device: Device number (not pointer)
*
- * Device selection hook. If neccessary perform clock switching
+ * Device selection hook. If necessary perform clock switching
*/
static void it821x_passthru_dev_select(struct ata_port *ap,
{
struct it821x_dev *itdev = ap->private_data;
if (itdev && device != itdev->last_device) {
- struct ata_device *adev = &ap->device[device];
+ struct ata_device *adev = &ap->link.device[device];
it821x_program(ap, adev, itdev->pio[adev->devno]);
itdev->last_device = device;
}
return ata_qc_issue_prot(qc);
}
printk(KERN_DEBUG "it821x: can't process command 0x%02X\n", qc->tf.command);
- return AC_ERR_INVALID;
+ return AC_ERR_DEV;
}
/**
/**
* it821x_smart_set_mode - mode setting
- * @ap: interface to set up
+ * @link: interface to set up
* @unused: device that failed (error only)
*
* Use a non standard set_mode function. We don't want to be tuned.
* and respect them.
*/
-static int it821x_smart_set_mode(struct ata_port *ap, struct ata_device **unused)
+static int it821x_smart_set_mode(struct ata_link *link, struct ata_device **unused)
{
- int i;
+ struct ata_device *dev;
- for (i = 0; i < ATA_MAX_DEVICES; i++) {
- struct ata_device *dev = &ap->device[i];
+ ata_link_for_each_dev(dev, link) {
if (ata_dev_enabled(dev)) {
/* We don't really care */
dev->pio_mode = XFER_PIO_0;
printk("(%dK stripe)", adev->id[146]);
printk(".\n");
}
+ /* This is a controller firmware triggered funny, don't
+ report the drive faulty! */
+ adev->horkage &= ~ATA_HORKAGE_DIAGNOSTIC;
+}
+
+/**
+ * it821x_ident_hack - Hack identify data up
+ * @ap: Port
+ *
+ * Walk the devices on this firmware driven port and slightly
+ * mash the identify data to stop us and common tools trying to
+ * use features not firmware supported. The firmware itself does
+ * some masking (eg SMART) but not enough.
+ *
+ * This is a bit of an abuse of the cable method, but it is the
+ * only method called at the right time. We could modify the libata
+ * core specifically for ident hacking but while we have one offender
+ * it seems better to keep the fallout localised.
+ */
+
+static int it821x_ident_hack(struct ata_port *ap)
+{
+ struct ata_device *adev;
+ ata_link_for_each_dev(adev, &ap->link) {
+ if (ata_dev_enabled(adev)) {
+ adev->id[84] &= ~(1 << 6); /* No FUA */
+ adev->id[85] &= ~(1 << 10); /* No HPA */
+ adev->id[76] = 0; /* No NCQ/AN etc */
+ }
+ }
+ return ata_cable_unknown(ap);
}
struct ata_port *ap = qc->ap;
struct it821x_dev *itdev = ap->private_data;
+ /* Only use dma for transfers to/from the media. */
+ if (ata_qc_raw_nbytes(qc) < 2048)
+ return -EOPNOTSUPP;
+
/* No ATAPI DMA in smart mode */
if (itdev->smart)
return -EOPNOTSUPP;
struct it821x_dev *itdev;
u8 conf;
- int ret = ata_port_start(ap);
+ int ret = ata_sff_port_start(ap);
if (ret < 0)
return ret;
itdev->want[1][1] = ATA_ANY;
itdev->last_device = -1;
- pci_read_config_byte(pdev, PCI_REVISION_ID, &conf);
- if (conf == 0x10) {
+ if (pdev->revision == 0x10) {
itdev->timing10 = 1;
/* Need to disable ATAPI DMA for this case */
if (!itdev->smart)
static struct ata_port_operations it821x_smart_port_ops = {
.set_mode = it821x_smart_set_mode,
- .port_disable = ata_port_disable,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.mode_filter = ata_pci_default_filter,
.thaw = ata_bmdma_thaw,
.error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
- .cable_detect = ata_cable_unknown,
+ .cable_detect = it821x_ident_hack,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .irq_ack = ata_irq_ack,
.port_start = it821x_port_start,
};
static struct ata_port_operations it821x_passthru_port_ops = {
- .port_disable = ata_port_disable,
.set_piomode = it821x_passthru_set_piomode,
.set_dmamode = it821x_passthru_set_dmamode,
.mode_filter = ata_pci_default_filter,
.irq_clear = ata_bmdma_irq_clear,
.irq_handler = ata_interrupt,
.irq_on = ata_irq_on,
- .irq_ack = ata_irq_ack,
.port_start = it821x_port_start,
};
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &it821x_passthru_port_ops
};