* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
- * Portions Copyright (C) 2005-2006 MontaVista Software, Inc.
+ * Portions Copyright (C) 2005-2007 MontaVista Software, Inc.
*
*
* TODO
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
-#define DRV_VERSION "0.3.3"
+#define DRV_VERSION "0.3.4"
enum {
HPT_PCI_FAST = (1 << 31),
/**
* hpt3x2n_pre_reset - reset the hpt3x2n bus
- * @ap: ATA port to reset
+ * @link: ATA link to reset
* @deadline: deadline jiffies for the operation
*
* Perform the initial reset handling for the 3x2n series controllers.
* Reset the hardware and state machine,
*/
-static int hpt3xn_pre_reset(struct ata_port *ap)
+static int hpt3xn_pre_reset(struct ata_link *link, unsigned long deadline)
{
+ struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
/* Reset the state machine */
pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(100);
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(link, deadline);
}
/**
static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* HPT372N and friends - UDMA133 */
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &hpt3x2n_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &hpt3x2n_port_ops
};
- struct ata_port_info *port_info[2];
- struct ata_port_info *port = &info;
+ struct ata_port_info port = info;
+ const struct ata_port_info *ppi[] = { &port, NULL };
u8 irqmask;
u32 class_rev;
/* 371N if rev > 1 */
break;
case PCI_DEVICE_ID_TTI_HPT372:
- /* 372N if rev >= 1*/
- if (class_rev == 0)
+ /* 372N if rev >= 2*/
+ if (class_rev < 2)
return -ENODEV;
break;
case PCI_DEVICE_ID_TTI_HPT302:
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
}
if (adjust == 8) {
- printk(KERN_WARNING "hpt3x2n: DPLL did not stabilize.\n");
+ printk(KERN_ERR "pata_hpt3x2n: DPLL did not stabilize!\n");
return -ENODEV;
}
+ printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using 66MHz DPLL.\n",
+ pci_mhz);
/* Set our private data up. We only need a few flags so we use
it directly */
- port->private_data = NULL;
+ port.private_data = NULL;
if (pci_mhz > 60) {
- port->private_data = (void *)PCI66;
+ port.private_data = (void *)PCI66;
/*
* On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
* the MISC. register to stretch the UltraDMA Tss timing.
}
/* Now kick off ATA set up */
- port_info[0] = port_info[1] = port;
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id hpt3x2n[] = {