#include <linux/libata.h>
#define DRV_NAME "pata_hpt366"
-#define DRV_VERSION "0.5"
+#define DRV_VERSION "0.5.3"
struct hpt_clock {
u8 xfer_speed;
static int hpt36x_pre_reset(struct ata_port *ap)
{
+ static const struct pci_bits hpt36x_enable_bits[] = {
+ { 0x50, 1, 0x04, 0x04 },
+ { 0x54, 1, 0x04, 0x04 }
+ };
+
u8 ata66;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ if (!pci_test_config_bits(pdev, &hpt36x_enable_bits[ap->port_no]))
+ return -ENOENT;
+
pci_read_config_byte(pdev, 0x5A, &ata66);
if (ata66 & (1 << ap->port_no))
ap->cbl = ATA_CBL_PATA40;
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
- .max_sectors = ATA_MAX_SECTORS,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
/*
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .eng_timeout = ata_eng_timeout,
+
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.host_stop = ata_host_stop
};
+/**
+ * hpt36x_init_chipset - common chip setup
+ * @dev: PCI device
+ *
+ * Perform the chip setup work that must be done at both init and
+ * resume time
+ */
+
+static void hpt36x_init_chipset(struct pci_dev *dev)
+{
+ u8 drive_fast;
+ pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+ pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+ pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+ pci_read_config_byte(dev, 0x51, &drive_fast);
+ if (drive_fast & 0x80)
+ pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
+}
+
/**
* hpt36x_init_one - Initialise an HPT366/368
* @dev: PCI device
u32 class_rev;
u32 reg1;
- u8 drive_fast;
pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xFF;
if (class_rev > 2)
return -ENODEV;
- pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
- pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
- pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
- pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
-
- pci_read_config_byte(dev, 0x51, &drive_fast);
- if (drive_fast & 0x80)
- pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
+ hpt36x_init_chipset(dev);
pci_read_config_dword(dev, 0x40, ®1);
/* PCI clocking determines the ATA timing values to use */
/* info_hpt366 is safe against re-entry so we can scribble on it */
- switch(reg1 & 0x700) {
+ switch((reg1 & 0x700) >> 8) {
case 5:
info_hpt366.private_data = &hpt366_40;
break;
return ata_pci_init_one(dev, port_info, 2);
}
-static struct pci_device_id hpt36x[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
- { 0, },
+static int hpt36x_reinit_one(struct pci_dev *dev)
+{
+ hpt36x_init_chipset(dev);
+ return ata_pci_device_resume(dev);
+}
+
+
+static const struct pci_device_id hpt36x[] = {
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
+ { },
};
static struct pci_driver hpt36x_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = hpt36x,
.probe = hpt36x_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = hpt36x_reinit_one,
};
static int __init hpt36x_init(void)
return pci_register_driver(&hpt36x_pci_driver);
}
-
static void __exit hpt36x_exit(void)
{
pci_unregister_driver(&hpt36x_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
MODULE_LICENSE("GPL");