}
static struct scsi_host_template cs5520_sht = {
- .module = THIS_MODULE,
- .name = DRV_NAME,
- .ioctl = ata_scsi_ioctl,
- .queuecommand = ata_scsi_queuecmd,
- .can_queue = ATA_DEF_QUEUE,
- .this_id = ATA_SHT_THIS_ID,
+ ATA_BMDMA_SHT(DRV_NAME),
.sg_tablesize = LIBATA_DUMB_MAX_PRD,
- .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
- .emulated = ATA_SHT_EMULATED,
- .use_clustering = ATA_SHT_USE_CLUSTERING,
- .proc_name = DRV_NAME,
- .dma_boundary = ATA_DMA_BOUNDARY,
- .slave_configure = ata_scsi_slave_config,
- .slave_destroy = ata_scsi_slave_destroy,
- .bios_param = ata_std_bios_param,
};
static struct ata_port_operations cs5520_port_ops = {
- .port_disable = ata_port_disable,
+ .inherits = &ata_bmdma_port_ops,
+ .qc_prep = ata_sff_dumb_qc_prep,
+ .cable_detect = ata_cable_40wire,
.set_piomode = cs5520_set_piomode,
.set_dmamode = cs5520_set_dmamode,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = ata_bmdma_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
- .cable_detect = ata_cable_40wire,
-
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = ata_bmdma_start,
- .bmdma_stop = ata_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
- .qc_prep = ata_dumb_qc_prep,
- .qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_data_xfer,
-
- .irq_clear = ata_bmdma_irq_clear,
- .irq_on = ata_irq_on,
- .irq_ack = ata_irq_ack,
-
- .port_start = ata_port_start,
};
static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
+ static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
+ static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
struct ata_port_info pi = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
};
const struct ata_port_info *ppi[2];
u8 pcicfg;
- void *iomap[5];
+ void __iomem *iomap[5];
struct ata_host *host;
struct ata_ioports *ioaddr;
int i, rc;
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+
/* IDE port enable bits */
pci_read_config_byte(pdev, 0x60, &pcicfg);
return -ENOMEM;
/* Perform set up for DMA */
- if (pci_enable_device_bars(pdev, 1<<2)) {
+ if (pci_enable_device_io(pdev)) {
printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
return -ENODEV;
}
}
/* Map IO ports and initialize host accordingly */
- iomap[0] = devm_ioport_map(&pdev->dev, 0x1F0, 8);
- iomap[1] = devm_ioport_map(&pdev->dev, 0x3F6, 1);
- iomap[2] = devm_ioport_map(&pdev->dev, 0x170, 8);
- iomap[3] = devm_ioport_map(&pdev->dev, 0x376, 1);
+ iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
+ iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
+ iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
+ iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
iomap[4] = pcim_iomap(pdev, 2, 0);
if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
ioaddr->ctl_addr = iomap[1];
ioaddr->altstatus_addr = iomap[1];
ioaddr->bmdma_addr = iomap[4];
- ata_std_ports(ioaddr);
+ ata_sff_std_ports(ioaddr);
+
+ ata_port_desc(host->ports[0],
+ "cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
+ ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
ioaddr = &host->ports[1]->ioaddr;
ioaddr->cmd_addr = iomap[2];
ioaddr->ctl_addr = iomap[3];
ioaddr->altstatus_addr = iomap[3];
ioaddr->bmdma_addr = iomap[4] + 8;
- ata_std_ports(ioaddr);
+ ata_sff_std_ports(ioaddr);
+
+ ata_port_desc(host->ports[1],
+ "cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
+ ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
/* activate the host */
pci_set_master(pdev);
continue;
rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
- ata_interrupt, 0, DRV_NAME, host);
+ ata_sff_interrupt, 0, DRV_NAME, host);
if (rc)
return rc;
- if (i == 0)
- host->irq = irq[0];
- else
- host->irq2 = irq[1];
+ ata_port_desc(ap, "irq %d", irq[i]);
}
return ata_host_register(host, &cs5520_sht);
}
-/**
- * cs5520_remove_one - device unload
- * @pdev: PCI device being removed
- *
- * Handle an unplug/unload event for a PCI device. Unload the
- * PCI driver but do not use the default handler as we manage
- * resources ourself and *MUST NOT* disable the device as it has
- * other functions.
- */
-
-static void __devexit cs5520_remove_one(struct pci_dev *pdev)
-{
- struct device *dev = pci_dev_to_dev(pdev);
- struct ata_host *host = dev_get_drvdata(dev);
-
- ata_host_detach(host);
-}
-
#ifdef CONFIG_PM
/**
* cs5520_reinit_one - device resume
static int cs5520_reinit_one(struct pci_dev *pdev)
{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
u8 pcicfg;
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+
pci_read_config_byte(pdev, 0x60, &pcicfg);
if ((pcicfg & 0x40) == 0)
pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
- return ata_pci_device_resume(pdev);
+
+ ata_host_resume(host);
+ return 0;
}
/**
.name = DRV_NAME,
.id_table = pata_cs5520,
.probe = cs5520_init_one,
- .remove = cs5520_remove_one,
+ .remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = cs5520_pci_device_suspend,
.resume = cs5520_reinit_one,