If you don't know what to do here, say N.
-config PREEMPT
- bool "Preemptible Kernel"
- ---help---
- This option reduces the latency of the kernel when reacting to
- real-time or interactive events by allowing a low priority process to
- be preempted even if it is in kernel mode executing a system call.
- This allows applications to run more reliably even when the system is
- under load. On contrary it may also break your drivers and add
- priority inheritance problems to your system. Don't select it if
- you rely on a stable system or have slightly obscure hardware.
- It's also not very well tested on x86-64 currently.
- You have been warned.
-
- Say Y here if you are feeling brave and building a kernel for a
- desktop, embedded or real-time system. Say N if you are unsure.
-
-config PREEMPT_BKL
- bool "Preempt The Big Kernel Lock"
- depends on PREEMPT
- default y
- help
- This option reduces the latency of the kernel by making the
- big kernel lock preemptible.
-
- Say Y here if you are building a kernel for a desktop system.
- Say N if you are unsure.
-
config SCHED_SMT
bool "SMT (Hyperthreading) scheduler support"
depends on SMP
cost of slightly increased overhead in some places. If unsure say
N here.
+source "kernel/Kconfig.preempt"
+
config K8_NUMA
bool "K8 NUMA support"
select NUMA
into virtual nodes when booted with "numa=fake=N", where N is the
number of nodes. This is only useful for debugging.
-config DISCONTIGMEM
+config ARCH_DISCONTIGMEM_ENABLE
bool
depends on NUMA
default y
bool
default n
+config ARCH_DISCONTIGMEM_ENABLE
+ def_bool y
+ depends on NUMA
+
+config ARCH_DISCONTIGMEM_DEFAULT
+ def_bool y
+ depends on NUMA
+
+config ARCH_SPARSEMEM_ENABLE
+ def_bool y
+ depends on NUMA
+
+config ARCH_FLATMEM_ENABLE
+ def_bool y
+ depends on !NUMA
+
+source "mm/Kconfig"
+
+config HAVE_ARCH_EARLY_PFN_TO_NID
+ def_bool y
+
config HAVE_DEC_LOCK
bool
depends on SMP
This is purely to save memory - each supported CPU requires
memory in the static kernel configuration.
+config HOTPLUG_CPU
+ bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
+ depends on SMP && HOTPLUG && EXPERIMENTAL
+ help
+ Say Y here to experiment with turning CPUs off and on. CPUs
+ can be controlled through /sys/devices/system/cpu/cpu#.
+ Say N if you want to disable CPU hotplug.
+
+
config HPET_TIMER
bool
default y
config X86_PM_TIMER
bool "PM timer"
+ depends on ACPI
default y
help
Support the ACPI PM timer for time keeping. This is slow,
Additional support for intel specific MCE features such as
the thermal monitor.
+config PHYSICAL_START
+ hex "Physical address where the kernel is loaded" if EMBEDDED
+ default "0x100000"
+ help
+ This gives the physical address where the kernel is loaded.
+ Primarily used in the case of kexec on panic where the
+ fail safe kernel needs to run at a different address than
+ the panic-ed kernel.
+
+ Don't change this unless you know what you are doing.
+
+config KEXEC
+ bool "kexec system call (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ help
+ kexec is a system call that implements the ability to shutdown your
+ current kernel, and to start another kernel. It is like a reboot
+ but it is indepedent of the system firmware. And like a reboot
+ you can start any kernel with it, not just Linux.
+
+ The name comes from the similiarity to the exec system call.
+
+ It is an ongoing process to be certain the hardware in a machine
+ is properly shutdown, so do not be surprised if this code does not
+ initially work for you. It may help to enable device hotplugging
+ support. As of this writing the exact hardware interface is
+ strongly in flux, so no good recommendation can be made.
+
config SECCOMP
bool "Enable seccomp to safely compute untrusted bytecode"
depends on PROC_FS
If unsure, say Y. Only embedded should say N here.
+source kernel/Kconfig.hz
+
endmenu
#