bool
default y
+config DMI
+ bool
+ default y
+
source "init/Kconfig"
menu "Processor type and features"
+choice
+ prompt "Subarchitecture Type"
+ default X86_PC
+
+config X86_PC
+ bool "PC-compatible"
+ help
+ Choose this option if your computer is a standard PC or compatible.
+
+config X86_VSMP
+ bool "Support for ScaleMP vSMP"
+ help
+ Support for ScaleMP vSMP systems. Say 'Y' here if this kernel is
+ supposed to run on these EM64T-based machines. Only choose this option
+ if you have one of these machines.
+
+endchoice
+
choice
prompt "Processor family"
default MK8
config ARCH_SPARSEMEM_ENABLE
def_bool y
- depends on NUMA
+ depends on (NUMA || EXPERIMENTAL)
+
+config ARCH_MEMORY_PROBE
+ def_bool y
+ depends on MEMORY_HOTPLUG
config ARCH_FLATMEM_ENABLE
def_bool y
config HAVE_ARCH_EARLY_PFN_TO_NID
def_bool y
+ depends on NUMA
config NR_CPUS
int "Maximum number of CPUs (2-256)"
- range 2 256
+ range 2 255
depends on SMP
default "8"
help
as it is off-chip. You can find the HPET spec at
<http://www.intel.com/hardwaredesign/hpetspec.htm>.
-config X86_PM_TIMER
- bool "PM timer"
- depends on ACPI
- default y
- help
- Support the ACPI PM timer for time keeping. This is slow,
- but is useful on some chipsets without HPET on systems with more
- than one CPU. On a single processor or single socket multi core
- system it is normally not required.
- When the PM timer is active 64bit vsyscalls are disabled
- and should not be enabled (/proc/sys/kernel/vsyscall64 should
- not be changed).
- The kernel selects the PM timer only as a last resort, so it is
- useful to enable just in case.
-
config HPET_EMULATE_RTC
bool "Provide RTC interrupt"
depends on HPET_TIMER && RTC=y
config GART_IOMMU
- bool "IOMMU support"
+ bool "K8 GART IOMMU support"
default y
+ select SWIOTLB
depends on PCI
help
Support the IOMMU. Needed to run systems with more than 3GB of memory
properly with 32-bit PCI devices that do not support DAC (Double Address
Cycle). The IOMMU can be turned off at runtime with the iommu=off parameter.
Normally the kernel will take the right choice by itself.
- This option includes a driver for the AMD Opteron/Athlon64 IOMMU
- and a software emulation used on some other systems.
+ This option includes a driver for the AMD Opteron/Athlon64 northbridge IOMMU
+ and a software emulation used on other systems.
If unsure, say Y.
# need this always enabled with GART_IOMMU for the VIA workaround
config SWIOTLB
- bool
- depends on GART_IOMMU
- default y
-
-config DUMMY_IOMMU
bool
- depends on !GART_IOMMU && !SWIOTLB
default y
- help
- Don't use IOMMU code. This will cause problems when you have more than 4GB
- of memory and any 32-bit devices. Don't turn on unless you know what you
- are doing.
+ depends on GART_IOMMU
config X86_MCE
bool "Machine check support" if EMBEDDED
Additional support for AMD specific MCE features such as
the DRAM Error Threshold.
-config PHYSICAL_START
- hex "Physical address where the kernel is loaded" if EMBEDDED
- default "0x100000"
- help
- This gives the physical address where the kernel is loaded.
- Primarily used in the case of kexec on panic where the
- fail safe kernel needs to run at a different address than
- the panic-ed kernel.
-
- Don't change this unless you know what you are doing.
-
config KEXEC
bool "kexec system call (EXPERIMENTAL)"
depends on EXPERIMENTAL
support. As of this writing the exact hardware interface is
strongly in flux, so no good recommendation can be made.
+config CRASH_DUMP
+ bool "kernel crash dumps (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ help
+ Generate crash dump after being started by kexec.
+
+config PHYSICAL_START
+ hex "Physical address where the kernel is loaded" if (EMBEDDED || CRASH_DUMP)
+ default "0x1000000" if CRASH_DUMP
+ default "0x200000"
+ help
+ This gives the physical address where the kernel is loaded. Normally
+ for regular kernels this value is 0x200000 (2MB). But in the case
+ of kexec on panic the fail safe kernel needs to run at a different
+ address than the panic-ed kernel. This option is used to set the load
+ address for kernels used to capture crash dump on being kexec'ed
+ after panic. The default value for crash dump kernels is
+ 0x1000000 (16MB). This can also be set based on the "X" value as
+ specified in the "crashkernel=YM@XM" command line boot parameter
+ passed to the panic-ed kernel. Typically this parameter is set as
+ crashkernel=64M@16M. Please take a look at
+ Documentation/kdump/kdump.txt for more details about crash dumps.
+
+ Don't change this unless you know what you are doing.
+
config SECCOMP
bool "Enable seccomp to safely compute untrusted bytecode"
depends on PROC_FS
source kernel/Kconfig.hz
+config REORDER
+ bool "Function reordering"
+ default n
+ help
+ This option enables the toolchain to reorder functions for a more
+ optimal TLB usage. If you have pretty much any version of binutils,
+ this can increase your kernel build time by roughly one minute.
+
endmenu
#
depends on COMPAT && SYSVIPC
default y
-config UID16
- bool
- depends on IA32_EMULATION
- default y
-
endmenu
source "net/Kconfig"
config KPROBES
bool "Kprobes (EXPERIMENTAL)"
+ depends on EXPERIMENTAL && MODULES
help
Kprobes allows you to trap at almost any kernel address and
execute a callback function. register_kprobe() establishes