#endif
#include <linux/ata_platform.h>
#include <linux/irq.h>
+#include <linux/i2c.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/reboot.h>
};
#endif
+#if defined(CONFIG_MTD_BF5xx) || defined(CONFIG_MTD_BF5xx_MODULE)
static struct mtd_partition stamp_partitions[] = {
{
.name = "Bootloader",
- .size = 0x20000,
+ .size = 0x40000,
.offset = 0,
}, {
.name = "Kernel",
.num_resources = ARRAY_SIZE(stamp_flash_resource),
.resource = stamp_flash_resource,
};
+#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* all SPI peripherals info goes here */
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader",
- .size = 0x00020000,
+ .size = 0x00040000,
.offset = 0,
.mask_flags = MTD_CAP_ROM
}, {
.name = "kernel",
.size = 0xe0000,
- .offset = 0x20000
+ .offset = MTDPART_OFS_APPEND,
}, {
.name = "file system",
- .size = 0x700000,
- .offset = 0x00100000,
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
}
};
};
#endif
-#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
-static struct bfin5xx_spi_chip ad5304_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
static struct bfin5xx_spi_chip spi_mmc_chip_info = {
.enable_dma = 1,
};
#endif
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
{
},
#endif
-#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
{
- .modalias = "ad5304_spi",
- .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .modalias = "spidev",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 2,
- .platform_data = NULL,
- .controller_data = &ad5304_chip_info,
- .mode = SPI_MODE_2,
+ .chip_select = 1,
+ .controller_data = &spidev_chip_info,
},
#endif
};
};
#endif
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+ .name = "bfin_sir",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sir_resources),
+ .resource = bfin_sir_resources,
+};
+#endif
+
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
static struct platform_device bfin_sport0_uart_device = {
.name = "bfin-sport-uart",
#include <linux/gpio_keys.h>
static struct gpio_keys_button bfin_gpio_keys_table[] = {
- {BTN_0, GPIO_PF5, 1, "gpio-keys: BTN0"},
- {BTN_1, GPIO_PF6, 1, "gpio-keys: BTN1"},
- {BTN_2, GPIO_PF8, 1, "gpio-keys: BTN2"},
+ {BTN_0, GPIO_PF5, 0, "gpio-keys: BTN0"},
+ {BTN_1, GPIO_PF6, 0, "gpio-keys: BTN1"},
+ {BTN_2, GPIO_PF8, 0, "gpio-keys: BTN2"},
};
static struct gpio_keys_platform_data bfin_gpio_keys_data = {
};
#endif
+static struct resource bfin_gpios_resources = {
+ .start = 0,
+ .end = MAX_BLACKFIN_GPIOS - 1,
+ .flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+ .name = "simple-gpio",
+ .id = -1,
+ .num_resources = 1,
+ .resource = &bfin_gpios_resources,
+};
+
#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
#include <linux/i2c-gpio.h>
};
#endif
+#ifdef CONFIG_I2C_BOARDINFO
+static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+#if defined(CONFIG_JOYSTICK_AD7142) || defined(CONFIG_JOYSTICK_AD7142_MODULE)
+ {
+ I2C_BOARD_INFO("ad7142_joystick", 0x2C),
+ .irq = 39,
+ },
+#endif
+#if defined(CONFIG_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE)
+ {
+ I2C_BOARD_INFO("pcf8574_lcd", 0x22),
+ },
+#endif
+#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+ {
+ I2C_BOARD_INFO("pcf8574_keypad", 0x27),
+ .irq = 39,
+ },
+#endif
+};
+#endif
+
static struct platform_device *stamp_devices[] __initdata = {
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
&rtc_device,
&bfin_uart_device,
#endif
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+ &bfin_sir_device,
+#endif
+
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
&bfin_sport0_uart_device,
&bfin_sport1_uart_device,
#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
&i2c_gpio_device,
#endif
+
+ &bfin_gpios_device,
+
+#if defined(CONFIG_MTD_BF5xx) || defined(CONFIG_MTD_BF5xx_MODULE)
&stamp_flash_device,
+#endif
};
static int __init stamp_init(void)
{
int ret;
- printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+ printk(KERN_INFO "%s(): registering device resources\n", __func__);
+
+#ifdef CONFIG_I2C_BOARDINFO
+ i2c_register_board_info(0, bfin_i2c_board_info,
+ ARRAY_SIZE(bfin_i2c_board_info));
+#endif
+
ret = platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
if (ret < 0)
return ret;