config IRQCHIP_DEMUX_GPIO
bool
- depends on (BF53x || BF561 || BF54x)
+ depends on (BF52x || BF53x || BF561 || BF54x)
default y
source "init/Kconfig"
prompt "CPU"
default BF533
+config BF522
+ bool "BF522"
+ help
+ BF522 Processor Support.
+
+config BF525
+ bool "BF525"
+ help
+ BF525 Processor Support.
+
+config BF527
+ bool "BF527"
+ help
+ BF527 Processor Support.
+
config BF531
bool "BF531"
help
choice
prompt "Silicon Rev"
+ default BF_REV_0_1 if BF527
default BF_REV_0_2 if BF537
default BF_REV_0_3 if BF533
default BF_REV_0_0 if BF549
config BF_REV_0_0
bool "0.0"
- depends on (BF549)
+ depends on (BF549 || BF527)
+
+config BF_REV_0_1
+ bool "0.2"
+ depends on (BF549 || BF527)
config BF_REV_0_2
bool "0.2"
endchoice
+config BF52x
+ bool
+ depends on (BF522 || BF525 || BF527)
+ default y
+
config BF53x
bool
depends on (BF531 || BF532 || BF533 || BF534 || BF536 || BF537)
configuration to ensure that all the other settings are
correct.
+config BFIN527_EZKIT
+ bool "BF527-EZKIT"
+ depends on (BF522 || BF525 || BF527)
+ help
+ BF533-EZKIT-LITE board Support.
+
config BFIN533_EZKIT
bool "BF533-EZKIT"
depends on (BF533 || BF532 || BF531)
help
PNAV 1.0 board Support.
+config H8606_HVSISTEMAS
+ bool "HV Sistemas H8606"
+ depends on (BF532)
+ help
+ HV Sistemas H8606 board support.
+
config GENERIC_BOARD
bool "Custom"
depends on (BF537 || BF536 \
config MEM_MT48LC16M16A2TG_75
bool
depends on (BFIN533_EZKIT || BFIN561_EZKIT \
- || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM)
+ || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \
+ || H8606_HVSISTEMAS)
default y
config MEM_MT48LC32M8A2_75
depends on (BFIN561_BLUETECHNIX_CM)
default y
+config MEM_MT48LC32M16A2TG_75
+ bool
+ depends on (BFIN527_EZKIT)
+ default y
+
config BFIN_SHARED_FLASH_ENET
bool
depends on (BFIN533_STAMP)
default y
+source "arch/blackfin/mach-bf527/Kconfig"
source "arch/blackfin/mach-bf533/Kconfig"
source "arch/blackfin/mach-bf561/Kconfig"
source "arch/blackfin/mach-bf537/Kconfig"
int "Crystal Frequency in Hz"
default "11059200" if BFIN533_STAMP
default "27000000" if BFIN533_EZKIT
- default "25000000" if BFIN537_STAMP
+ default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS)
default "30000000" if BFIN561_EZKIT
default "24576000" if PNAV10
help
range 1 64
default "22" if BFIN533_EZKIT
default "45" if BFIN533_STAMP
- default "20" if BFIN537_STAMP
+ default "20" if (BFIN537_STAMP || BFIN527_EZKIT)
default "22" if BFIN533_BLUETECHNIX_CM
default "20" if BFIN537_BLUETECHNIX_CM
default "20" if BFIN561_BLUETECHNIX_CM
default "20" if BFIN561_EZKIT
+ default "16" if H8606_HVSISTEMAS
help
This controls the frequency of the on-chip PLL. This can be between 1 and 64.
PLL Frequency = (Crystal Frequency) * (this setting)
range 1 15
default 5 if BFIN533_EZKIT
default 5 if BFIN533_STAMP
- default 4 if BFIN537_STAMP
+ default 4 if (BFIN537_STAMP || BFIN527_EZKIT)
default 5 if BFIN533_BLUETECHNIX_CM
default 4 if BFIN537_BLUETECHNIX_CM
default 4 if BFIN561_BLUETECHNIX_CM
default 5 if BFIN561_EZKIT
+ default 3 if H8606_HVSISTEMAS
help
This sets the frequency of the system clock (including SDRAM or DDR).
This can be between 1 and 15
config MEM_SIZE
int "SDRAM Memory Size in MBytes"
default 32 if BFIN533_EZKIT
+ default 64 if BFIN527_EZKIT
default 64 if BFIN537_STAMP
default 64 if BFIN561_EZKIT
default 128 if BFIN533_STAMP
default 64 if PNAV10
+ default 32 if H8606_HVSISTEMAS
config MEM_ADD_WIDTH
int "SDRAM Memory Address Width"
default 9 if BFIN533_EZKIT
default 9 if BFIN561_EZKIT
+ default 9 if H8606_HVSISTEMAS
+ default 10 if BFIN527_EZKIT
default 10 if BFIN537_STAMP
default 11 if BFIN533_STAMP
default 10 if PNAV10
bool "Locate interrupt entry code in L1 Memory"
default y
help
- If enabled interrupt entry code (STORE/RESTORE CONTEXT) is linked
- into L1 instruction memory.(less latency)
+ If enabled, interrupt entry code (STORE/RESTORE CONTEXT) is linked
+ into L1 instruction memory. (less latency)
config EXCPT_IRQ_SYSC_L1
- bool "Locate entire ASM lowlevel excepetion / interrupt - Syscall and CPLB handler code in L1 Memory"
+ bool "Locate entire ASM lowlevel exception / interrupt - Syscall and CPLB handler code in L1 Memory"
default y
help
- If enabled entire ASM lowlevel exception and interrupt entry code (STORE/RESTORE CONTEXT) is linked
- into L1 instruction memory.(less latency)
+ If enabled, the entire ASM lowlevel exception and interrupt entry code
+ (STORE/RESTORE CONTEXT) is linked into L1 instruction memory.
+ (less latency)
config DO_IRQ_L1
bool "Locate frequently called do_irq dispatcher function in L1 Memory"
default y
help
- If enabled frequently called do_irq dispatcher function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the frequently called do_irq dispatcher function is linked
+ into L1 instruction memory. (less latency)
config CORE_TIMER_IRQ_L1
bool "Locate frequently called timer_interrupt() function in L1 Memory"
default y
help
- If enabled frequently called timer_interrupt() function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the frequently called timer_interrupt() function is linked
+ into L1 instruction memory. (less latency)
config IDLE_L1
bool "Locate frequently idle function in L1 Memory"
default y
help
- If enabled frequently called idle function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the frequently called idle function is linked
+ into L1 instruction memory. (less latency)
config SCHEDULE_L1
bool "Locate kernel schedule function in L1 Memory"
default y
help
- If enabled frequently called kernel schedule is linked
- into L1 instruction memory.(less latency)
+ If enabled, the frequently called kernel schedule is linked
+ into L1 instruction memory. (less latency)
config ARITHMETIC_OPS_L1
bool "Locate kernel owned arithmetic functions in L1 Memory"
default y
help
- If enabled arithmetic functions are linked
- into L1 instruction memory.(less latency)
+ If enabled, arithmetic functions are linked
+ into L1 instruction memory. (less latency)
config ACCESS_OK_L1
bool "Locate access_ok function in L1 Memory"
default y
help
- If enabled access_ok function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the access_ok function is linked
+ into L1 instruction memory. (less latency)
config MEMSET_L1
bool "Locate memset function in L1 Memory"
default y
help
- If enabled memset function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the memset function is linked
+ into L1 instruction memory. (less latency)
config MEMCPY_L1
bool "Locate memcpy function in L1 Memory"
default y
help
- If enabled memcpy function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the memcpy function is linked
+ into L1 instruction memory. (less latency)
config SYS_BFIN_SPINLOCK_L1
bool "Locate sys_bfin_spinlock function in L1 Memory"
default y
help
- If enabled sys_bfin_spinlock function is linked
- into L1 instruction memory.(less latency)
+ If enabled, sys_bfin_spinlock function is linked
+ into L1 instruction memory. (less latency)
config IP_CHECKSUM_L1
bool "Locate IP Checksum function in L1 Memory"
default n
help
- If enabled IP Checksum function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the IP Checksum function is linked
+ into L1 instruction memory. (less latency)
config CACHELINE_ALIGNED_L1
bool "Locate cacheline_aligned data to L1 Data Memory"
default n if BF54x
depends on !BF531
help
- If enabled cacheline_anligned data is linked
- into L1 data memory.(less latency)
+ If enabled, cacheline_anligned data is linked
+ into L1 data memory. (less latency)
config SYSCALL_TAB_L1
bool "Locate Syscall Table L1 Data Memory"
default n
depends on !BF531
help
- If enabled the Syscall LUT is linked
- into L1 data memory.(less latency)
+ If enabled, the Syscall LUT is linked
+ into L1 data memory. (less latency)
config CPLB_SWITCH_TAB_L1
bool "Locate CPLB Switch Tables L1 Data Memory"
default n
depends on !BF531
help
- If enabled the CPLB Switch Tables are linked
- into L1 data memory.(less latency)
+ If enabled, the CPLB Switch Tables are linked
+ into L1 data memory. (less latency)
endmenu
a lot of RAM, and you need to able to allocate very large
contiguous chunks. If unsure, say N.
+config BFIN_GPTIMERS
+ tristate "Enable Blackfin General Purpose Timers API"
+ default n
+ help
+ Enable support for the General Purpose Timers API. If you
+ are unsure, say N.
+
+ To compile this driver as a module, choose M here: the module
+ will be called gptimers.ko.
+
config BFIN_DMA_5XX
bool "Enable DMA Support"
- depends on (BF533 || BF532 || BF531 || BF537 || BF536 || BF534 || BF561 || BF54x)
+ depends on (BF52x || BF53x || BF561 || BF54x)
default y
help
DMA driver for BF5xx.
choice
prompt "Uncached SDRAM region"
default DMA_UNCACHED_1M
- depends BFIN_DMA_5XX
+ depends on BFIN_DMA_5XX
config DMA_UNCACHED_2M
bool "Enable 2M DMA region"
config DMA_UNCACHED_1M
source "fs/Kconfig"
-source "arch/blackfin/oprofile/Kconfig"
+source "kernel/Kconfig.instrumentation"
menu "Kernel hacking"
from.
config DEBUG_ICACHE_CHECK
- bool "Check Instruction cache coherancy"
+ bool "Check Instruction cache coherency"
depends on DEBUG_KERNEL
depends on DEBUG_HWERR
help
- Say Y here if you are getting wierd unexplained errors. This will
- ensure that icache is what SDRAM says it should be, by doing a
- byte wise comparision between SDRAM and instruction cache. This
+ Say Y here if you are getting weird unexplained errors. This will
+ ensure that icache is what SDRAM says it should be by doing a
+ byte wise comparison between SDRAM and instruction cache. This
also relocates the irq_panic() function to L1 memory, (which is
un-cached).