config IRQCHIP_DEMUX_GPIO
bool
- depends on (BF53x || BF561 || BF54x)
+ depends on (BF52x || BF53x || BF561 || BF54x)
default y
source "init/Kconfig"
prompt "CPU"
default BF533
+config BF522
+ bool "BF522"
+ help
+ BF522 Processor Support.
+
+config BF525
+ bool "BF525"
+ help
+ BF525 Processor Support.
+
+config BF527
+ bool "BF527"
+ help
+ BF527 Processor Support.
+
config BF531
bool "BF531"
help
choice
prompt "Silicon Rev"
+ default BF_REV_0_1 if BF527
default BF_REV_0_2 if BF537
default BF_REV_0_3 if BF533
default BF_REV_0_0 if BF549
config BF_REV_0_0
bool "0.0"
- depends on (BF549)
+ depends on (BF549 || BF527)
+
+config BF_REV_0_1
+ bool "0.2"
+ depends on (BF549 || BF527)
config BF_REV_0_2
bool "0.2"
endchoice
+config BF52x
+ bool
+ depends on (BF522 || BF525 || BF527)
+ default y
+
config BF53x
bool
depends on (BF531 || BF532 || BF533 || BF534 || BF536 || BF537)
configuration to ensure that all the other settings are
correct.
+config BFIN527_EZKIT
+ bool "BF527-EZKIT"
+ depends on (BF522 || BF525 || BF527)
+ help
+ BF533-EZKIT-LITE board Support.
+
config BFIN533_EZKIT
bool "BF533-EZKIT"
depends on (BF533 || BF532 || BF531)
help
PNAV 1.0 board Support.
+config H8606_HVSISTEMAS
+ bool "HV Sistemas H8606"
+ depends on (BF532)
+ help
+ HV Sistemas H8606 board support.
+
config GENERIC_BOARD
bool "Custom"
depends on (BF537 || BF536 \
config MEM_MT48LC16M16A2TG_75
bool
depends on (BFIN533_EZKIT || BFIN561_EZKIT \
- || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM)
+ || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \
+ || H8606_HVSISTEMAS)
default y
config MEM_MT48LC32M8A2_75
depends on (BFIN561_BLUETECHNIX_CM)
default y
+config MEM_MT48LC32M16A2TG_75
+ bool
+ depends on (BFIN527_EZKIT)
+ default y
+
config BFIN_SHARED_FLASH_ENET
bool
depends on (BFIN533_STAMP)
default y
+source "arch/blackfin/mach-bf527/Kconfig"
source "arch/blackfin/mach-bf533/Kconfig"
source "arch/blackfin/mach-bf561/Kconfig"
source "arch/blackfin/mach-bf537/Kconfig"
int "Crystal Frequency in Hz"
default "11059200" if BFIN533_STAMP
default "27000000" if BFIN533_EZKIT
- default "25000000" if BFIN537_STAMP
+ default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS)
default "30000000" if BFIN561_EZKIT
default "24576000" if PNAV10
help
range 1 64
default "22" if BFIN533_EZKIT
default "45" if BFIN533_STAMP
- default "20" if BFIN537_STAMP
+ default "20" if (BFIN537_STAMP || BFIN527_EZKIT)
default "22" if BFIN533_BLUETECHNIX_CM
default "20" if BFIN537_BLUETECHNIX_CM
default "20" if BFIN561_BLUETECHNIX_CM
default "20" if BFIN561_EZKIT
+ default "16" if H8606_HVSISTEMAS
help
This controls the frequency of the on-chip PLL. This can be between 1 and 64.
PLL Frequency = (Crystal Frequency) * (this setting)
range 1 15
default 5 if BFIN533_EZKIT
default 5 if BFIN533_STAMP
- default 4 if BFIN537_STAMP
+ default 4 if (BFIN537_STAMP || BFIN527_EZKIT)
default 5 if BFIN533_BLUETECHNIX_CM
default 4 if BFIN537_BLUETECHNIX_CM
default 4 if BFIN561_BLUETECHNIX_CM
default 5 if BFIN561_EZKIT
+ default 3 if H8606_HVSISTEMAS
help
This sets the frequency of the system clock (including SDRAM or DDR).
This can be between 1 and 15
config MEM_SIZE
int "SDRAM Memory Size in MBytes"
default 32 if BFIN533_EZKIT
+ default 64 if BFIN527_EZKIT
default 64 if BFIN537_STAMP
default 64 if BFIN561_EZKIT
default 128 if BFIN533_STAMP
default 64 if PNAV10
+ default 32 if H8606_HVSISTEMAS
config MEM_ADD_WIDTH
int "SDRAM Memory Address Width"
default 9 if BFIN533_EZKIT
default 9 if BFIN561_EZKIT
+ default 9 if H8606_HVSISTEMAS
+ default 10 if BFIN527_EZKIT
default 10 if BFIN537_STAMP
default 11 if BFIN533_STAMP
default 10 if PNAV10
a lot of RAM, and you need to able to allocate very large
contiguous chunks. If unsure, say N.
+config BFIN_GPTIMERS
+ tristate "Enable Blackfin General Purpose Timers API"
+ default n
+ help
+ Enable support for the General Purpose Timers API. If you
+ are unsure, say N.
+
+ To compile this driver as a module, choose M here: the module
+ will be called gptimers.ko.
+
config BFIN_DMA_5XX
bool "Enable DMA Support"
- depends on (BF533 || BF532 || BF531 || BF537 || BF536 || BF534 || BF561 || BF54x)
+ depends on (BF52x || BF53x || BF561 || BF54x)
default y
help
DMA driver for BF5xx.