#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/i2c.h>
+#include <linux/leds.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
&osk5912_mcbsp1_device,
};
+static struct gpio_led tps_leds[] = {
+ /* NOTE: D9 and D2 have hardware blink support.
+ * Also, D9 requires non-battery power.
+ */
+ { .gpio = OSK_TPS_GPIO_LED_D9, .name = "d9", },
+ { .gpio = OSK_TPS_GPIO_LED_D2, .name = "d2", },
+ { .gpio = OSK_TPS_GPIO_LED_D3, .name = "d3", .active_low = 1,
+ .default_trigger = "heartbeat", },
+};
+
+static struct gpio_led_platform_data tps_leds_data = {
+ .num_leds = 3,
+ .leds = tps_leds,
+};
+
+static struct platform_device osk5912_tps_leds = {
+ .name = "leds-gpio",
+ .id = 0,
+ .dev.platform_data = &tps_leds_data,
+};
+
+static int osk_tps_setup(struct i2c_client *client, void *context)
+{
+ /* Set GPIO 1 HIGH to disable VBUS power supply;
+ * OHCI driver powers it up/down as needed.
+ */
+ gpio_request(OSK_TPS_GPIO_USB_PWR_EN, "n_vbus_en");
+ gpio_direction_output(OSK_TPS_GPIO_USB_PWR_EN, 1);
+
+ /* Set GPIO 2 high so LED D3 is off by default */
+ tps65010_set_gpio_out_value(GPIO2, HIGH);
+
+ /* Set GPIO 3 low to take ethernet out of reset */
+ gpio_request(OSK_TPS_GPIO_LAN_RESET, "smc_reset");
+ gpio_direction_output(OSK_TPS_GPIO_LAN_RESET, 0);
+
+ /* GPIO4 is VDD_DSP */
+ gpio_request(OSK_TPS_GPIO_DSP_PWR_EN, "dsp_power");
+ gpio_direction_output(OSK_TPS_GPIO_DSP_PWR_EN, 1);
+ /* REVISIT if DSP support isn't configured, power it off ... */
+
+ /* Let LED1 (D9) blink; leds-gpio may override it */
+ tps65010_set_led(LED1, BLINK);
+
+ /* Set LED2 off by default */
+ tps65010_set_led(LED2, OFF);
+
+ /* Enable LOW_PWR handshake */
+ tps65010_set_low_pwr(ON);
+
+ /* Switch VLDO2 to 3.0V for AIC23 */
+ tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V
+ | TPS_LDO1_ENABLE);
+
+ /* register these three LEDs */
+ osk5912_tps_leds.dev.parent = &client->dev;
+ platform_device_register(&osk5912_tps_leds);
+
+ return 0;
+}
+
+static struct tps65010_board tps_board = {
+ .base = OSK_TPS_GPIO_BASE,
+ .outmask = 0x0f,
+ .setup = osk_tps_setup,
+};
+
static struct i2c_board_info __initdata osk_i2c_board_info[] = {
{
I2C_BOARD_INFO("tps65010", 0x48),
- .type = "tps65010",
.irq = OMAP_GPIO_IRQ(OMAP_MPUIO(1)),
+ .platform_data = &tps_board,
+
},
/* TODO when driver support is ready:
* - aic23 audio chip at 0x1a
static void __init osk_init_smc91x(void)
{
- if ((omap_request_gpio(0)) < 0) {
+ if ((gpio_request(0, "smc_irq")) < 0) {
printk("Error requesting gpio 0 for smc91x irq\n");
return;
}
static void __init osk_init_cf(void)
{
omap_cfg_reg(M7_1610_GPIO62);
- if ((omap_request_gpio(62)) < 0) {
+ if ((gpio_request(62, "cf_irq")) < 0) {
printk("Error requesting gpio 62 for CF irq\n");
return;
}
static int mistral_get_pendown_state(void)
{
- return !omap_get_gpio_datain(4);
+ return !gpio_get_value(4);
}
static const struct ads7846_platform_data mistral_ts_info = {
omap_cfg_reg(W14_1610_CCP_DATAP);
/* CAM_PWDN */
- if (omap_request_gpio(11) == 0) {
+ if (gpio_request(11, "cam_pwdn") == 0) {
omap_cfg_reg(N20_1610_GPIO11);
- omap_set_gpio_direction(11, 0 /* out */);
- omap_set_gpio_dataout(11, 0 /* off */);
+ gpio_direction_output(11, 0);
} else
pr_debug("OSK+Mistral: CAM_PWDN is awol\n");
/* omap_cfg_reg(P19_1610_GPIO6); */ /* BUSY */
+ gpio_request(6, "ts_busy");
+ gpio_direction_input(6);
+
omap_cfg_reg(P20_1610_GPIO4); /* PENIRQ */
+ gpio_request(4, "ts_int");
+ gpio_direction_input(4);
set_irq_type(OMAP_GPIO_IRQ(4), IRQT_FALLING);
+
spi_register_board_info(mistral_boardinfo,
ARRAY_SIZE(mistral_boardinfo));
/* the sideways button (SW1) is for use as a "wakeup" button */
omap_cfg_reg(N15_1610_MPUIO2);
- if (omap_request_gpio(OMAP_MPUIO(2)) == 0) {
+ if (gpio_request(OMAP_MPUIO(2), "wakeup") == 0) {
int ret = 0;
- omap_set_gpio_direction(OMAP_MPUIO(2), 1);
+
+ gpio_direction_input(OMAP_MPUIO(2));
set_irq_type(OMAP_GPIO_IRQ(OMAP_MPUIO(2)), IRQT_RISING);
#ifdef CONFIG_PM
/* share the IRQ in case someone wants to use the
IRQF_SHARED, "mistral_wakeup",
&osk_mistral_wake_interrupt);
if (ret != 0) {
- omap_free_gpio(OMAP_MPUIO(2));
+ gpio_free(OMAP_MPUIO(2));
printk(KERN_ERR "OSK+Mistral: no wakeup irq, %d?\n",
ret);
} else
* board, like the touchscreen, EEPROM, and wakeup (!) switch.
*/
omap_cfg_reg(PWL);
- if (omap_request_gpio(2) == 0) {
- omap_set_gpio_direction(2, 0 /* out */);
- omap_set_gpio_dataout(2, 1 /* on */);
- }
+ if (gpio_request(2, "lcd_pwr") == 0)
+ gpio_direction_output(2, 1);
platform_add_devices(mistral_devices, ARRAY_SIZE(mistral_devices));
}
omap1_map_common_io();
}
-#ifdef CONFIG_TPS65010
-static int __init osk_tps_init(void)
-{
- if (!machine_is_omap_osk())
- return 0;
-
- /* Let LED1 (D9) blink */
- tps65010_set_led(LED1, BLINK);
-
- /* Disable LED 2 (D2) */
- tps65010_set_led(LED2, OFF);
-
- /* Set GPIO 1 HIGH to disable VBUS power supply;
- * OHCI driver powers it up/down as needed.
- */
- tps65010_set_gpio_out_value(GPIO1, HIGH);
-
- /* Set GPIO 2 low to turn on LED D3 */
- tps65010_set_gpio_out_value(GPIO2, HIGH);
-
- /* Set GPIO 3 low to take ethernet out of reset */
- tps65010_set_gpio_out_value(GPIO3, LOW);
-
- /* gpio4 for VDD_DSP */
- /* FIXME send power to DSP iff it's configured */
-
- /* Enable LOW_PWR */
- tps65010_set_low_pwr(ON);
-
- /* Switch VLDO2 to 3.0V for AIC23 */
- tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V
- | TPS_LDO1_ENABLE);
-
- return 0;
-}
-fs_initcall(osk_tps_init);
-#endif
-
MACHINE_START(OMAP_OSK, "TI-OSK")
/* Maintainer: Dirk Behme <dirk.behme@de.bosch.com> */
.phys_io = 0xfff00000,
projects / linux-2.6 / blobdiff