#include <asm/mach/flash.h>
#include <asm/mach/map.h>
+#include <asm/arch/gpio-switch.h>
#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
#include <asm/arch/nand.h>
#include <asm/arch/mcbsp.h>
#include <asm/arch/omap-alsa.h>
-extern int omap_gpio_init(void);
-
static int h2_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
&h2_mcbsp1_device,
};
-#ifdef CONFIG_I2C_BOARDINFO
-static struct i2c_board_info __initdata h2_i2c_board_info[] = {
- {
- I2C_BOARD_INFO("tps65010", 0x48),
- .type = "tps65010",
- .irq = OMAP_GPIO_IRQ(58),
- },
- /* TODO when driver support is ready:
- * - isp1301 OTG transceiver
- * - optional ov9640 camera sensor at 0x30
- * - pcf9754 for aGPS control
- * - ... etc
- */
-};
-#endif
-
static void __init h2_init_smc91x(void)
{
if ((omap_request_gpio(0)) < 0) {
}
}
+static struct i2c_board_info __initdata h2_i2c_board_info[] = {
+ {
+ I2C_BOARD_INFO("tps65010", 0x48),
+ .irq = OMAP_GPIO_IRQ(58),
+ }, {
+ I2C_BOARD_INFO("isp1301_omap", 0x2d),
+ .irq = OMAP_GPIO_IRQ(2),
+ },
+};
+
static void __init h2_init_irq(void)
{
omap1_init_common_hw();
};
static struct omap_mmc_config h2_mmc_config __initdata = {
- .mmc [0] = {
- .enabled = 1,
+ .mmc[0] = {
+ .enabled = 1,
.wire4 = 1,
- .wp_pin = OMAP_MPUIO(3),
- .power_pin = -1, /* tps65010 gpio3 */
- .switch_pin = OMAP_MPUIO(1),
},
};
+extern struct omap_mmc_platform_data h2_mmc_data;
+
static struct omap_uart_config h2_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
omap_serial_init();
-
- /* irq for tps65010 chip */
- omap_cfg_reg(W4_GPIO58);
- if (gpio_request(58, "tps65010") == 0)
- gpio_direction_input(58);
-
-#ifdef CONFIG_I2C_BOARDINFO
- i2c_register_board_info(1, h2_i2c_board_info,
- ARRAY_SIZE(h2_i2c_board_info));
-#endif
+ omap_register_i2c_bus(1, 100, h2_i2c_board_info,
+ ARRAY_SIZE(h2_i2c_board_info));
+ h2_mmc_init();
}
static void __init h2_map_io(void)
omap1_map_common_io();
}
-#ifdef CONFIG_TPS65010
-static int __init h2_tps_init(void)
-{
- if (!machine_is_omap_h2())
- return 0;
-
- /* gpio3 for SD, gpio4 for VDD_DSP */
- /* FIXME send power to DSP iff it's configured */
-
- /* Enable LOW_PWR */
- tps65010_set_low_pwr(ON);
- return 0;
-}
-fs_initcall(h2_tps_init);
-#endif
-
MACHINE_START(OMAP_H2, "TI-H2")
/* Maintainer: Imre Deak <imre.deak@nokia.com> */
.phys_io = 0xfff00000,