#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
+#include <linux/fb.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+
+#include <video/atmel_lcdc.h>
#include <asm/hardware.h>
#include <asm/setup.h>
* MACB Ethernet device
*/
static struct at91_eth_data __initdata ek_macb_data = {
+ .phy_irq_pin = AT91_PIN_PE31,
.is_rmii = 1,
};
},
};
-static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
{
*num_partitions = ARRAY_SIZE(ek_nand_partition);
return ek_nand_partition;
};
+/*
+ * LCD Controller
+ */
+#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
+static struct fb_videomode at91_tft_vga_modes[] = {
+ {
+ .name = "TX09D50VM1CCA @ 60",
+ .refresh = 60,
+ .xres = 240, .yres = 320,
+ .pixclock = KHZ2PICOS(4965),
+
+ .left_margin = 1, .right_margin = 33,
+ .upper_margin = 1, .lower_margin = 0,
+ .hsync_len = 5, .vsync_len = 1,
+
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+};
+
+static struct fb_monspecs at91fb_default_monspecs = {
+ .manufacturer = "HIT",
+ .monitor = "TX09D70VM1CCA",
+
+ .modedb = at91_tft_vga_modes,
+ .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
+ .hfmin = 15000,
+ .hfmax = 64000,
+ .vfmin = 50,
+ .vfmax = 150,
+};
+
+#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
+ | ATMEL_LCDC_DISTYPE_TFT \
+ | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
+
+static void at91_lcdc_power_control(int on)
+{
+ if (on)
+ at91_set_gpio_value(AT91_PIN_PD12, 0); /* power up */
+ else
+ at91_set_gpio_value(AT91_PIN_PD12, 1); /* power down */
+}
+
+/* Driver datas */
+static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+ .default_bpp = 16,
+ .default_dmacon = ATMEL_LCDC_DMAEN,
+ .default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
+ .default_monspecs = &at91fb_default_monspecs,
+ .atmel_lcdfb_power_control = at91_lcdc_power_control,
+ .guard_time = 1,
+};
+
+#else
+static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+#endif
+
+
+/*
+ * GPIO Buttons
+ */
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button ek_buttons[] = {
+ { /* BP1, "leftclic" */
+ .code = BTN_LEFT,
+ .gpio = AT91_PIN_PC5,
+ .active_low = 1,
+ .desc = "left_click",
+ .wakeup = 1,
+ },
+ { /* BP2, "rightclic" */
+ .code = BTN_RIGHT,
+ .gpio = AT91_PIN_PC4,
+ .active_low = 1,
+ .desc = "right_click",
+ .wakeup = 1,
+ },
+};
+
+static struct gpio_keys_platform_data ek_button_data = {
+ .buttons = ek_buttons,
+ .nbuttons = ARRAY_SIZE(ek_buttons),
+};
+
+static struct platform_device ek_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &ek_button_data,
+ }
+};
+
+static void __init ek_add_device_buttons(void)
+{
+ at91_set_GPIO_periph(AT91_PIN_PC5, 0); /* left button */
+ at91_set_deglitch(AT91_PIN_PC5, 1);
+ at91_set_GPIO_periph(AT91_PIN_PC4, 0); /* right button */
+ at91_set_deglitch(AT91_PIN_PC4, 1);
+
+ platform_device_register(&ek_button_device);
+}
+#else
+static void __init ek_add_device_buttons(void) {}
+#endif
+
+
/*
* AC97
*/
};
+/*
+ * LEDs ... these could all be PWM-driven, for variable brightness
+ */
+static struct gpio_led ek_leds[] = {
+ { /* "left" led, green, userled1, pwm1 */
+ .name = "ds1",
+ .gpio = AT91_PIN_PB8,
+ .active_low = 1,
+ .default_trigger = "mmc0",
+ },
+ { /* "right" led, green, userled2, pwm2 */
+ .name = "ds2",
+ .gpio = AT91_PIN_PC29,
+ .active_low = 1,
+ .default_trigger = "nand-disk",
+ },
+ { /* "power" led, yellow, pwm0 */
+ .name = "ds3",
+ .gpio = AT91_PIN_PB7,
+ .default_trigger = "heartbeat",
+ },
+};
+
+
static void __init ek_board_init(void)
{
/* Serial */
/* NAND */
at91_add_device_nand(&ek_nand_data);
/* I2C */
- at91_add_device_i2c();
+ at91_add_device_i2c(NULL, 0);
+ /* LCD Controller */
+ at91_add_device_lcdc(&ek_lcdc_data);
+ /* Push Buttons */
+ ek_add_device_buttons();
/* AC97 */
at91_add_device_ac97(&ek_ac97_data);
+ /* LEDs */
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")