Europe. There is an ARM Linux project with a web page at
<http://www.arm.linux.org.uk/>.
+config GENERIC_TIME
+ bool
+ default n
+
config MMU
bool
default y
config RWSEM_XCHGADD_ALGORITHM
bool
+config ARCH_HAS_ILOG2_U32
+ bool
+ default n
+
+config ARCH_HAS_ILOG2_U64
+ bool
+ default n
+
config GENERIC_HWEIGHT
bool
default y
config VECTORS_BASE
hex
- default 0xffff0000 if MMU
+ default 0xffff0000 if MMU || CPU_HIGH_VECTOR
default DRAM_BASE if REMAP_VECTORS_TO_RAM
default 0x00000000
help
help
Support for Intel's IOP33X (XScale) family of processors.
+config ARCH_IOP13XX
+ bool "IOP13xx-based"
+ select PCI
+ help
+ Support for Intel's IOP13XX (XScale) family of processors.
+
config ARCH_IXP4XX
bool "IXP4xx-based"
depends on MMU
+ select GENERIC_TIME
help
Support for Intel's IXP4XX (XScale) family of processors.
source "arch/arm/mach-iop33x/Kconfig"
+source "arch/arm/mach-iop13xx/Kconfig"
+
source "arch/arm/mach-ixp4xx/Kconfig"
source "arch/arm/mach-ixp2000/Kconfig"
source arch/arm/mm/Kconfig
+config IWMMXT
+ bool "Enable iWMMXt support"
+ depends CPU_XSCALE || CPU_XSC3
+ default y if PXA27x
+ help
+ Enable support for iWMMXt context switching at run time if
+ running on a CPU that supports it.
+
# bool 'Use XScale PMU as timer source' CONFIG_XSCALE_PMU_TIMER
config XSCALE_PMU
bool
ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \
ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \
ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE || \
- ARCH_AT91RM9200 || MACH_TRIZEPS4
+ ARCH_AT91 || MACH_TRIZEPS4
help
If you say Y here, the LEDs on your machine will be used
to provide useful information about your current system status.
config ALIGNMENT_TRAP
bool
+ depends on CPU_CP15_MMU
default y if !ARCH_EBSA110
help
- ARM processors can not fetch/store information which is not
+ ARM processors cannot fetch/store information which is not
naturally aligned on the bus, i.e., a 4 byte fetch must start at an
address divisible by 4. On 32-bit ARM processors, these non-aligned
fetch/store instructions will be emulated in software if you say
hex "Compressed ROM boot loader BSS address"
default "0"
help
- The base address of 64KiB of read/write memory in the target
- for the ROM-able zImage, which must be available while the
- decompressor is running. Platforms which normally make use of
- ROM-able zImage formats normally set this to a suitable
- value in their defconfig file.
+ The base address of an area of read/write memory in the target
+ for the ROM-able zImage which must be available while the
+ decompressor is running. It must be large enough to hold the
+ entire decompressed kernel plus an additional 128 KiB.
+ Platforms which normally make use of ROM-able zImage formats
+ normally set this to a suitable value in their defconfig file.
If ZBOOT_ROM is not enabled, this has no effect.
endmenu
-if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP)
+if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_IMX )
menu "CPU Frequency scaling"
If in doubt, say Y.
+config CPU_FREQ_IMX
+ tristate "CPUfreq driver for i.MX CPUs"
+ depends on ARCH_IMX && CPU_FREQ
+ default n
+ help
+ This enables the CPUfreq driver for i.MX CPUs.
+
+ If in doubt, say N.
+
endmenu
endif
source "drivers/connector/Kconfig"
-if ALIGNMENT_TRAP
+if ALIGNMENT_TRAP || !CPU_CP15_MMU
source "drivers/mtd/Kconfig"
endif
source "drivers/scsi/Kconfig"
+source "drivers/ata/Kconfig"
+
source "drivers/md/Kconfig"
source "drivers/message/fusion/Kconfig"
source "sound/Kconfig"
+source "drivers/hid/Kconfig"
+
source "drivers/usb/Kconfig"
source "drivers/mmc/Kconfig"