APIC APIC support is enabled.
APM Advanced Power Management support is enabled.
AX25 Appropriate AX.25 support is enabled.
+ BLACKFIN Blackfin architecture is enabled.
DRM Direct Rendering Management support is enabled.
EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
EFI EFI Partitioning (GPT) is enabled
PARIDE The ParIDE (parallel port IDE) subsystem is enabled.
PARISC The PA-RISC architecture is enabled.
PCI PCI bus support is enabled.
+ PCIE PCI Express support is enabled.
PCMCIA The PCMCIA subsystem is enabled.
PNP Plug & Play support is enabled.
PPC PowerPC architecture is enabled.
blkmtd_bs=
blkmtd_count=
+ boot_delay= Milliseconds to delay each printk during boot.
+ Values larger than 10 seconds (10000) are changed to
+ no delay (0).
+ Format: integer
+
bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
bttv.radio= Most important insmod options are available as
kernel args too.
Format:
<first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
- cpia_pp= [HW,PPT]
- Format: { parport<nr> | auto | none }
-
crashkernel=nn[KMG]@ss[KMG]
[KNL] Reserve a chunk of physical memory to
hold a kernel to switch to with kexec on panic.
dtc3181e= [HW,SCSI]
- earlyprintk= [X86-32,X86-64,SH]
+ earlyprintk= [X86-32,X86-64,SH,BLACKFIN]
earlyprintk=vga
earlyprintk=serial[,ttySn[,baudrate]]
lasi= [HW,SCSI] PARISC LASI driver for the 53c700 chip
Format: addr:<io>,irq:<irq>
+ libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
+ when set.
+ Format: <int>
+
load_ramdisk= [RAM] List of ramdisks to load from floppy
See Documentation/ramdisk.txt.
Format: <1-256>
maxcpus= [SMP] Maximum number of processors that an SMP kernel
- should make use of.
- Using "nosmp" or "maxcpus=0" will disable SMP
- entirely (the MPS table probe still happens, though).
- A command-line option of "maxcpus=<NUM>", where <NUM>
- is an integer greater than 0, limits the maximum number
- of CPUs activated in SMP mode to <NUM>.
- Using "maxcpus=1" on an SMP kernel is the trivial
- case of an SMP kernel with only one CPU.
+ should make use of. maxcpus=n : n >= 0 limits the
+ kernel to using 'n' processors. n=0 is a special case,
+ it is equivalent to "nosmp", which also disables
+ the IO APIC.
max_addr=[KMG] [KNL,BOOT,ia64] All physical memory greater than or
equal to this physical address is ignored.
meye.*= [HW] Set MotionEye Camera parameters
See Documentation/video4linux/meye.txt.
+ mfgpt_irq= [IA-32] Specify the IRQ to use for the
+ Multi-Function General Purpose Timers on AMD Geode
+ platforms.
+
mga= [HW,DRM]
mousedev.tap_time=
[NFS] set the maximum lifetime for idmapper cache
entries.
+ nfs.enable_ino64=
+ [NFS] enable 64-bit inode numbers.
+ If zero, the NFS client will fake up a 32-bit inode
+ number for the readdir() and stat() syscalls instead
+ of returning the full 64-bit number.
+ The default is to return 64-bit inode numbers.
+
nmi_watchdog= [KNL,BUGS=X86-32] Debugging features for SMP kernels
no387 [BUGS=X86-32] Tells the kernel to use the 387 maths
emulation library even if a 387 maths coprocessor
is present.
- noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
- when set.
- Format: <int>
-
noaliencache [MM, NUMA, SLAB] Disables the allocation of alien
caches in the slab allocator. Saves per-node memory,
but will impact performance.
nomce [X86-32] Machine Check Exception
+ nomfgpt [X86-32] Disable Multi-Function General Purpose
+ Timer usage (for AMD Geode machines).
+
noreplace-paravirt [X86-32,PV_OPS] Don't patch paravirt_ops
noreplace-smp [X86-32,SMP] Don't replace SMP instructions
nosep [BUGS=X86-32] Disables x86 SYSENTER/SYSEXIT support.
- nosmp [SMP] Tells an SMP kernel to act as a UP kernel.
+ nosmp [SMP] Tells an SMP kernel to act as a UP kernel,
+ and disable the IO APIC. legacy for "maxcpus=0".
nosoftlockup [KNL] Disable the soft-lockup detector.
Mechanism 1.
conf2 [X86-32] Force use of PCI Configuration
Mechanism 2.
+ noaer [PCIE] If the PCIEAER kernel config parameter is
+ enabled, this kernel boot option can be used to
+ disable the use of PCIE advanced error reporting.
+ nodomains [PCI] Disable support for multiple PCI
+ root domains (aka PCI segments, in ACPI-speak).
nommconf [X86-32,X86_64] Disable use of MMCONFIG for PCI
Configuration
nomsi [MSI] If the PCI_MSI kernel config parameter is
IRQ routing is enabled.
noacpi [X86-32] Do not use ACPI for IRQ routing
or for PCI scanning.
+ use_crs [X86-32] Use _CRS for PCI resource
+ allocation.
routeirq Do IRQ routing for all PCI devices.
This is normally done in pci_enable_device(),
so this option is a temporary workaround
pt. [PARIDE]
See Documentation/paride.txt.
+ pty.legacy_count=
+ [KNL] Number of legacy pty's. Overwrites compiled-in
+ default number.
+
quiet [KNL] Disable most log messages
r128= [HW,DRM]
-1: disable all active trip points in all thermal zones
<degrees C>: override all lowest active trip points
+ thermal.crt= [HW,ACPI]
+ -1: disable all critical trip points in all thermal zones
+ <degrees C>: lower all critical trip points
+
thermal.nocrt= [HW,ACPI]
Set to disable actions on ACPI thermal zone
critical and hot trip points.
Format:
<io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
- tsdev.xres= [TS] Horizontal screen resolution.
- tsdev.yres= [TS] Vertical screen resolution.
-
turbografx.map[2|3]= [HW,JOY]
TurboGraFX parallel port interface
Format:
projects / linux-2.6 / blobdiff