hugetlb: fix pool resizing corner case

[linux-2.6] / Documentation / kernel-parameters.txt

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 83e21045114e3631dcbae20b56572f65ffe5f6c8..760ed57761749815419f59f47f1948ad5259d0d7 100644 (file)
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -35,6 +35,7 @@ parameter is applicable:
        APIC    APIC support is enabled.
        APM     Advanced Power Management support is enabled.
        AX25    Appropriate AX.25 support is enabled.
+       BLACKFIN Blackfin architecture is enabled.
        DRM     Direct Rendering Management support is enabled.
        EDD     BIOS Enhanced Disk Drive Services (EDD) is enabled
        EFI     EFI Partitioning (GPT) is enabled
@@ -67,6 +68,7 @@ parameter is applicable:
        PARIDE  The ParIDE (parallel port IDE) subsystem is enabled.
        PARISC  The PA-RISC architecture is enabled.
        PCI     PCI bus support is enabled.
+       PCIE    PCI Express support is enabled.
        PCMCIA  The PCMCIA subsystem is enabled.
        PNP     Plug & Play support is enabled.
        PPC     PowerPC architecture is enabled.
@@ -347,6 +349,11 @@ and is between 256 and 4096 characters. It is defined in the file
        blkmtd_bs=
        blkmtd_count=
 
+       boot_delay=     Milliseconds to delay each printk during boot.
+                       Values larger than 10 seconds (10000) are changed to
+                       no delay (0).
+                       Format: integer
+
        bttv.card=      [HW,V4L] bttv (bt848 + bt878 based grabber cards)
        bttv.radio=     Most important insmod options are available as
                        kernel args too.
@@ -550,7 +557,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
        dtc3181e=       [HW,SCSI]
 
-       earlyprintk=    [X86-32,X86-64,SH]
+       earlyprintk=    [X86-32,X86-64,SH,BLACKFIN]
                        earlyprintk=vga
                        earlyprintk=serial[,ttySn[,baudrate]]
 
@@ -863,6 +870,10 @@ and is between 256 and 4096 characters. It is defined in the file
        lasi=           [HW,SCSI] PARISC LASI driver for the 53c700 chip
                        Format: addr:<io>,irq:<irq>
 
+       libata.noacpi   [LIBATA] Disables use of ACPI in libata suspend/resume
+                       when set.
+                       Format: <int>
+
        load_ramdisk=   [RAM] List of ramdisks to load from floppy
                        See Documentation/ramdisk.txt.
 
@@ -1008,6 +1019,10 @@ and is between 256 and 4096 characters. It is defined in the file
        meye.*=         [HW] Set MotionEye Camera parameters
                        See Documentation/video4linux/meye.txt.
 
+       mfgpt_irq=      [IA-32] Specify the IRQ to use for the
+                       Multi-Function General Purpose Timers on AMD Geode
+                       platforms.
+
        mga=            [HW,DRM]
 
        mousedev.tap_time=
@@ -1086,10 +1101,6 @@ and is between 256 and 4096 characters. It is defined in the file
                        emulation library even if a 387 maths coprocessor
                        is present.
 
-       noacpi          [LIBATA] Disables use of ACPI in libata suspend/resume
-                       when set.
-                       Format: <int>
-
        noaliencache    [MM, NUMA, SLAB] Disables the allocation of alien
                        caches in the slab allocator.  Saves per-node memory,
                        but will impact performance.
@@ -1166,6 +1177,9 @@ and is between 256 and 4096 characters. It is defined in the file
 
        nomce           [X86-32] Machine Check Exception
 
+       nomfgpt         [X86-32] Disable Multi-Function General Purpose
+                       Timer usage (for AMD Geode machines).
+
        noreplace-paravirt      [X86-32,PV_OPS] Don't patch paravirt_ops
 
        noreplace-smp   [X86-32,SMP] Don't replace SMP instructions
@@ -1276,6 +1290,11 @@ and is between 256 and 4096 characters. It is defined in the file
                                Mechanism 1.
                conf2           [X86-32] Force use of PCI Configuration
                                Mechanism 2.
+               noaer           [PCIE] If the PCIEAER kernel config parameter is
+                               enabled, this kernel boot option can be used to
+                               disable the use of PCIE advanced error reporting.
+               nodomains       [PCI] Disable support for multiple PCI
+                               root domains (aka PCI segments, in ACPI-speak).
                nommconf        [X86-32,X86_64] Disable use of MMCONFIG for PCI
                                Configuration
                nomsi           [MSI] If the PCI_MSI kernel config parameter is
@@ -1320,6 +1339,8 @@ and is between 256 and 4096 characters. It is defined in the file
                                IRQ routing is enabled.
                noacpi          [X86-32] Do not use ACPI for IRQ routing
                                or for PCI scanning.
+               use_crs         [X86-32] Use _CRS for PCI resource
+                               allocation.
                routeirq        Do IRQ routing for all PCI devices.
                                This is normally done in pci_enable_device(),
                                so this option is a temporary workaround
@@ -1436,6 +1457,10 @@ and is between 256 and 4096 characters. It is defined in the file
        pt.             [PARIDE]
                        See Documentation/paride.txt.
 
+       pty.legacy_count=
+                       [KNL] Number of legacy pty's. Overwrites compiled-in
+                       default number.
+
        quiet           [KNL] Disable most log messages
 
        r128=           [HW,DRM]
@@ -1870,9 +1895,6 @@ and is between 256 and 4096 characters. It is defined in the file
                        Format:
                        <io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
 
-       tsdev.xres=     [TS] Horizontal screen resolution.
-       tsdev.yres=     [TS] Vertical screen resolution.
-
        turbografx.map[2|3]=    [HW,JOY]
                        TurboGraFX parallel port interface
                        Format: