+ {0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
+ {0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ /* Disable digital (SPDIF) pins */
+ {0x03, AC_VERB_SET_DIGI_CONVERT_1, 0},
+ {0x06, AC_VERB_SET_DIGI_CONVERT_1, 0},
+
+ /* Ensure Mic1 and Line1 pin widgets take input from the OUT1 sum
+ * bus when acting as outputs.
+ */
+ {0x0b, AC_VERB_SET_CONNECT_SEL, 0},
+ {0x0d, AC_VERB_SET_CONNECT_SEL, 0},
+
+ /* Start with output sum widgets muted and their output gains at min */
+ {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
+ {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
+ {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
+
+ /* Unmute Line-out pin widget amp left and right (no equiv mixer ctrl) */
+ {0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ /* Unmute Mic1 and Line1 pin widget input buffers since they start as
+ * inputs. If the pin mode is changed by the user the pin mode control
+ * will take care of enabling the pin's input/output buffers as needed.
+ * Therefore there's no need to enable the input buffer at this
+ * stage.
+ */
+ {0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
+ {0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
+
+ /* Mute capture amp left and right */
+ {0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ /* Set ADC connection select to match default mixer setting - mic
+ * (on mic1 pin)
+ */
+ {0x04, AC_VERB_SET_CONNECT_SEL, 0x00},
+
+ /* Do similar with the second ADC: mute capture input amp and
+ * set ADC connection to mic to match ALSA's default state.
+ */
+ {0x05, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x05, AC_VERB_SET_CONNECT_SEL, 0x00},
+
+ /* Mute all inputs to mixer widget (even unconnected ones) */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, /* mic1 pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, /* mic2 pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, /* line1 pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, /* line2 pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, /* CD pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)}, /* Beep-gen pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)}, /* Line-out pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)}, /* HP-pin pin */
+
+ { }
+};
+
+/* Test configuration for debugging, modelled after the ALC880 test
+ * configuration.
+ */
+#ifdef CONFIG_SND_DEBUG
+static hda_nid_t alc260_test_dac_nids[1] = {
+ 0x02,
+};
+static hda_nid_t alc260_test_adc_nids[2] = {
+ 0x04, 0x05,
+};
+/* For testing the ALC260, each input MUX needs its own definition since
+ * the signal assignments are different. This assumes that the first ADC
+ * is NID 0x04.
+ */
+static struct hda_input_mux alc260_test_capture_sources[2] = {
+ {
+ .num_items = 7,
+ .items = {
+ { "MIC1 pin", 0x0 },
+ { "MIC2 pin", 0x1 },
+ { "LINE1 pin", 0x2 },
+ { "LINE2 pin", 0x3 },
+ { "CD pin", 0x4 },
+ { "LINE-OUT pin", 0x5 },
+ { "HP-OUT pin", 0x6 },
+ },
+ },
+ {
+ .num_items = 8,
+ .items = {
+ { "MIC1 pin", 0x0 },
+ { "MIC2 pin", 0x1 },
+ { "LINE1 pin", 0x2 },
+ { "LINE2 pin", 0x3 },
+ { "CD pin", 0x4 },
+ { "Mixer", 0x5 },
+ { "LINE-OUT pin", 0x6 },
+ { "HP-OUT pin", 0x7 },
+ },
+ },
+};
+static struct snd_kcontrol_new alc260_test_mixer[] = {
+ /* Output driver widgets */
+ HDA_CODEC_VOLUME_MONO("Mono Playback Volume", 0x0a, 1, 0x0, HDA_OUTPUT),
+ HDA_BIND_MUTE_MONO("Mono Playback Switch", 0x0a, 1, 2, HDA_INPUT),
+ HDA_CODEC_VOLUME("LOUT2 Playback Volume", 0x09, 0x0, HDA_OUTPUT),
+ HDA_BIND_MUTE("LOUT2 Playback Switch", 0x09, 2, HDA_INPUT),
+ HDA_CODEC_VOLUME("LOUT1 Playback Volume", 0x08, 0x0, HDA_OUTPUT),
+ HDA_BIND_MUTE("LOUT1 Playback Switch", 0x08, 2, HDA_INPUT),
+
+ /* Modes for retasking pin widgets
+ * Note: the ALC260 doesn't seem to act on requests to enable mic
+ * bias from NIDs 0x0f and 0x10. The ALC260 datasheet doesn't
+ * mention this restriction. At this stage it's not clear whether
+ * this behaviour is intentional or is a hardware bug in chip
+ * revisions available at least up until early 2006. Therefore for
+ * now allow the "HP-OUT" and "LINE-OUT" Mode controls to span all
+ * choices, but if it turns out that the lack of mic bias for these
+ * NIDs is intentional we could change their modes from
+ * ALC_PIN_DIR_INOUT to ALC_PIN_DIR_INOUT_NOMICBIAS.
+ */
+ ALC_PIN_MODE("HP-OUT pin mode", 0x10, ALC_PIN_DIR_INOUT),
+ ALC_PIN_MODE("LINE-OUT pin mode", 0x0f, ALC_PIN_DIR_INOUT),
+ ALC_PIN_MODE("LINE2 pin mode", 0x15, ALC_PIN_DIR_INOUT),
+ ALC_PIN_MODE("LINE1 pin mode", 0x14, ALC_PIN_DIR_INOUT),
+ ALC_PIN_MODE("MIC2 pin mode", 0x13, ALC_PIN_DIR_INOUT),
+ ALC_PIN_MODE("MIC1 pin mode", 0x12, ALC_PIN_DIR_INOUT),
+
+ /* Loopback mixer controls */
+ HDA_CODEC_VOLUME("MIC1 Playback Volume", 0x07, 0x00, HDA_INPUT),
+ HDA_CODEC_MUTE("MIC1 Playback Switch", 0x07, 0x00, HDA_INPUT),
+ HDA_CODEC_VOLUME("MIC2 Playback Volume", 0x07, 0x01, HDA_INPUT),
+ HDA_CODEC_MUTE("MIC2 Playback Switch", 0x07, 0x01, HDA_INPUT),
+ HDA_CODEC_VOLUME("LINE1 Playback Volume", 0x07, 0x02, HDA_INPUT),
+ HDA_CODEC_MUTE("LINE1 Playback Switch", 0x07, 0x02, HDA_INPUT),
+ HDA_CODEC_VOLUME("LINE2 Playback Volume", 0x07, 0x03, HDA_INPUT),
+ HDA_CODEC_MUTE("LINE2 Playback Switch", 0x07, 0x03, HDA_INPUT),
+ HDA_CODEC_VOLUME("CD Playback Volume", 0x07, 0x04, HDA_INPUT),
+ HDA_CODEC_MUTE("CD Playback Switch", 0x07, 0x04, HDA_INPUT),
+ HDA_CODEC_VOLUME("Beep Playback Volume", 0x07, 0x05, HDA_INPUT),
+ HDA_CODEC_MUTE("Beep Playback Switch", 0x07, 0x05, HDA_INPUT),
+ HDA_CODEC_VOLUME("LINE-OUT loopback Playback Volume", 0x07, 0x06, HDA_INPUT),
+ HDA_CODEC_MUTE("LINE-OUT loopback Playback Switch", 0x07, 0x06, HDA_INPUT),
+ HDA_CODEC_VOLUME("HP-OUT loopback Playback Volume", 0x07, 0x7, HDA_INPUT),
+ HDA_CODEC_MUTE("HP-OUT loopback Playback Switch", 0x07, 0x7, HDA_INPUT),
+
+ /* Controls for GPIO pins, assuming they are configured as outputs */
+ ALC_GPIO_DATA_SWITCH("GPIO pin 0", 0x01, 0x01),
+ ALC_GPIO_DATA_SWITCH("GPIO pin 1", 0x01, 0x02),
+ ALC_GPIO_DATA_SWITCH("GPIO pin 2", 0x01, 0x04),
+ ALC_GPIO_DATA_SWITCH("GPIO pin 3", 0x01, 0x08),
+
+ /* Switches to allow the digital IO pins to be enabled. The datasheet
+ * is ambigious as to which NID is which; testing on laptops which
+ * make this output available should provide clarification.
+ */
+ ALC_SPDIF_CTRL_SWITCH("SPDIF Playback Switch", 0x03, 0x01),
+ ALC_SPDIF_CTRL_SWITCH("SPDIF Capture Switch", 0x06, 0x01),
+
+ { } /* end */
+};
+static struct hda_verb alc260_test_init_verbs[] = {
+ /* Enable all GPIOs as outputs with an initial value of 0 */
+ {0x01, AC_VERB_SET_GPIO_DIRECTION, 0x0f},
+ {0x01, AC_VERB_SET_GPIO_DATA, 0x00},
+ {0x01, AC_VERB_SET_GPIO_MASK, 0x0f},
+
+ /* Enable retasking pins as output, initially without power amp */
+ {0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
+ {0x0f, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
+ {0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
+ {0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
+ {0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
+ {0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
+
+ /* Disable digital (SPDIF) pins initially, but users can enable
+ * them via a mixer switch. In the case of SPDIF-out, this initverb
+ * payload also sets the generation to 0, output to be in "consumer"
+ * PCM format, copyright asserted, no pre-emphasis and no validity
+ * control.
+ */
+ {0x03, AC_VERB_SET_DIGI_CONVERT_1, 0},
+ {0x06, AC_VERB_SET_DIGI_CONVERT_1, 0},
+
+ /* Ensure mic1, mic2, line1 and line2 pin widgets take input from the
+ * OUT1 sum bus when acting as an output.
+ */
+ {0x0b, AC_VERB_SET_CONNECT_SEL, 0},
+ {0x0c, AC_VERB_SET_CONNECT_SEL, 0},
+ {0x0d, AC_VERB_SET_CONNECT_SEL, 0},
+ {0x0e, AC_VERB_SET_CONNECT_SEL, 0},
+
+ /* Start with output sum widgets muted and their output gains at min */
+ {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
+ {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
+ {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
+
+ /* Unmute retasking pin widget output buffers since the default
+ * state appears to be output. As the pin mode is changed by the
+ * user the pin mode control will take care of enabling the pin's
+ * input/output buffers as needed.
+ */
+ {0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ {0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ {0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ {0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ {0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ {0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ /* Also unmute the mono-out pin widget */
+ {0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+
+ /* Mute capture amp left and right */
+ {0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ /* Set ADC connection select to match default mixer setting (mic1
+ * pin)
+ */
+ {0x04, AC_VERB_SET_CONNECT_SEL, 0x00},
+
+ /* Do the same for the second ADC: mute capture input amp and
+ * set ADC connection to mic1 pin
+ */
+ {0x05, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x05, AC_VERB_SET_CONNECT_SEL, 0x00},
+
+ /* Mute all inputs to mixer widget (even unconnected ones) */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, /* mic1 pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, /* mic2 pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, /* line1 pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, /* line2 pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, /* CD pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)}, /* Beep-gen pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)}, /* Line-out pin */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)}, /* HP-pin pin */