-/* register offsets for gpio control */
-#define LED_GPIO_PIN 51
-#define STDBY_GPIO_PIN 48
-#define RST_GPIO_PIN 49
-#define RDY_GPIO_PIN 32
-#define ERR_GPIO_PIN 17
-#define PCBPWR_GPIO_PIN 16
-
-#define AF_SEL_GPIO_N 0x3
-#define GAFR0_U_OFFSET(pin) ((pin - 16) * 2)
-#define GAFR1_L_OFFSET(pin) ((pin - 32) * 2)
-#define GAFR1_U_OFFSET(pin) ((pin - 48) * 2)
-#define GPDR1_OFFSET(pin) (pin - 32)
-#define GPCR1_OFFSET(pin) (pin - 32)
-#define GPSR1_OFFSET(pin) (pin - 32)
-#define GPCR0_OFFSET(pin) (pin)
-#define GPSR0_OFFSET(pin) (pin)
-
-static void metronome_set_gpio_output(int pin, int val)
-{
- u8 index;
-
- index = pin >> 4;
-
- switch (index) {
- case 1:
- if (val)
- GPSR0 |= (1 << GPSR0_OFFSET(pin));
- else
- GPCR0 |= (1 << GPCR0_OFFSET(pin));
- break;
- case 2:
- break;
- case 3:
- if (val)
- GPSR1 |= (1 << GPSR1_OFFSET(pin));
- else
- GPCR1 |= (1 << GPCR1_OFFSET(pin));
- break;
- default:
- printk(KERN_ERR "unimplemented\n");
- }
-}
-
-static void __devinit metronome_init_gpio_pin(int pin, int dir)
-{
- u8 index;
- /* dir 0 is output, 1 is input
- - do 2 things here:
- - set gpio alternate function to standard gpio
- - set gpio direction to input or output */
-
- index = pin >> 4;
- switch (index) {
- case 1:
- GAFR0_U &= ~(AF_SEL_GPIO_N << GAFR0_U_OFFSET(pin));
-
- if (dir)
- GPDR0 &= ~(1 << pin);
- else
- GPDR0 |= (1 << pin);
- break;
- case 2:
- GAFR1_L &= ~(AF_SEL_GPIO_N << GAFR1_L_OFFSET(pin));
-
- if (dir)
- GPDR1 &= ~(1 << GPDR1_OFFSET(pin));
- else
- GPDR1 |= (1 << GPDR1_OFFSET(pin));
- break;
- case 3:
- GAFR1_U &= ~(AF_SEL_GPIO_N << GAFR1_U_OFFSET(pin));
-
- if (dir)
- GPDR1 &= ~(1 << GPDR1_OFFSET(pin));
- else
- GPDR1 |= (1 << GPDR1_OFFSET(pin));
- break;
- default:
- printk(KERN_ERR "unimplemented\n");
- }
-}
-
-static void __devinit metronome_init_gpio_regs(void)
-{
- metronome_init_gpio_pin(LED_GPIO_PIN, 0);
- metronome_set_gpio_output(LED_GPIO_PIN, 0);
-
- metronome_init_gpio_pin(STDBY_GPIO_PIN, 0);
- metronome_set_gpio_output(STDBY_GPIO_PIN, 0);
-
- metronome_init_gpio_pin(RST_GPIO_PIN, 0);
- metronome_set_gpio_output(RST_GPIO_PIN, 0);
-
- metronome_init_gpio_pin(RDY_GPIO_PIN, 1);
-
- metronome_init_gpio_pin(ERR_GPIO_PIN, 1);
-
- metronome_init_gpio_pin(PCBPWR_GPIO_PIN, 0);
- metronome_set_gpio_output(PCBPWR_GPIO_PIN, 0);
-}
-
-static void metronome_disable_lcd_controller(struct metronomefb_par *par)
-{
- LCSR = 0xffffffff; /* Clear LCD Status Register */
- LCCR0 |= LCCR0_DIS; /* Disable LCD Controller */
-
- /* we reset and just wait for things to settle */
- msleep(200);
-}
-
-static void metronome_enable_lcd_controller(struct metronomefb_par *par)
-{
- LCSR = 0xffffffff;
- FDADR0 = par->metromem_desc_dma;
- LCCR0 |= LCCR0_ENB;
-}
-
-static void __devinit metronome_init_lcdc_regs(struct metronomefb_par *par)
-{
- /* here we do:
- - disable the lcd controller
- - setup lcd control registers
- - setup dma descriptor
- - reenable lcd controller
- */
-
- /* disable the lcd controller */
- metronome_disable_lcd_controller(par);
-
- /* setup lcd control registers */
- LCCR0 = LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM | LCCR0_PAS
- | LCCR0_QDM | LCCR0_BM | LCCR0_OUM;
-
- LCCR1 = (epd_frame_table[0].fw/2 - 1) /* pixels per line */
- | (27 << 10) /* hsync pulse width - 1 */
- | (33 << 16) /* eol pixel count */
- | (33 << 24); /* bol pixel count */
-
- LCCR2 = (epd_frame_table[0].fh - 1) /* lines per panel */
- | (24 << 10) /* vsync pulse width - 1 */
- | (2 << 16) /* eof pixel count */
- | (0 << 24); /* bof pixel count */
-
- LCCR3 = 2 /* pixel clock divisor */
- | (24 << 8) /* AC Bias pin freq */
- | LCCR3_16BPP /* BPP */
- | LCCR3_PCP; /* PCP falling edge */
-
- /* setup dma descriptor */
- par->metromem_desc->mFDADR0 = par->metromem_desc_dma;
- par->metromem_desc->mFSADR0 = par->metromem_dma;
- par->metromem_desc->mFIDR0 = 0;
- par->metromem_desc->mLDCMD0 = epd_frame_table[0].fw
- * epd_frame_table[0].fh;
- /* reenable lcd controller */
- metronome_enable_lcd_controller(par);
-}
-